Renesas HD74CBT1G125 User Manual

HD74CBT1G125

Single FET Bus Switch

REJ03D0815-0100

(Previous: ADE-205-645)

Rev.1.00

Apr 07, 2006

Description

The HD74CBT1G125 features a single high-speed line switch. The switch is disabled when the output enable (OE)
input is high.

Features

• Minimal propagation delay through the switch.

• 5 Ω switch connection between two ports.

• TTL-compatible input levels.

• Ultra low quiescent power.
 Ideally suited for notebook applications.

• Ordering Information

Part Name Package Type

HD74CBT1G125CME CMPAK–5pin

Package Code

(Previous code)

PTSP0005ZC-A
(CMPAK–5V)

Package

Abbreviation

CM E (3,000pcs / Reel)

Taping Abbreviation

(Quantity)

Outline and Article Indication

• HD74CBT1G125

CMPAK–5

Function Table

Input OE Function

L A port = B port

H Disconnect
H: High level
L: Low level

Index band

Marking

B B

= Control code
( or blank)

Rev.1.00 Apr 07, 2006 page 1 of 6

HD74CBT1G125

Pin Arrangement

OE

A

GND

1

2

3

(Top view)

54V

CC

B

Absolute Maximum Ratings

Item Symbol Ratings Unit Conditions

Supply voltage range VCC −0.5 to 7.0 V
Input voltage range *1 V
Input clamp current IIK −50 mA VI < 0
Continuous output current IO 128 mA VO = 0 to VCC
Continuous current through VCC or GND ICC or I
Maximum power dissipation

at Ta = 25°C (in still air)

*2

Storage temperature Tstg −65 to 150 °C
Notes: The absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two

of which may be realized at the same time.

1. The input and output volta ge ratings may be exceeded even if the input and output clamp-current ratings are

observed.

2. The maximum package power dissipation was calculated using a junction temperature of 150°C.

−0.5 to 7.0 V

I

±100 mA

GND

200 mW

P

T

Recommended Operating Conditions

Item Symbol Min Max Unit Conditions

Supply voltage range VCC 4.0 5.5 V
Input voltage range VI 0 5.5 V
Output voltage range V
Input transition rise or fall rate ∆t / ∆v 0 5 ns / V VCC = 4.5 to 5.5 V
Operating free-air temperature Ta −40 85 °C
Note: Unused or floating inputs must be held high or low.

Rev.1.00 Apr 07, 2006 page 2 of 6

0 5.5 V

I/O

HD74CBT1G125

DC Electrical Characteristics

Item Symbol VCC (V) Min Typ

Clamp diode voltage VIK 4.5   −1.2 V IIN = −18 mA

VIH 4.0 to 5.5 2.0   Input voltage
VIL 4.0 to 5.5   0.8

On-state switch resistance *2 RON

4.0  14 20

4.5  5 7 VIN = 0 V, IIN = 64 mA

4.5  5 7 VIN = 0 V, IIN = 30 mA

4.5  10 15
Input current IIN 0 to 5.5   ±1.0 µA VIN = 5.5 V or GND
Off-state leakage current IOZ 5.5   ±1.0 µA 0 ≤ A, B ≤ VCC
Quiescent supply current ICC 5.5   1.0 µA VIN = VCC or GND, IO = 0 mA
Increase in ICC per input *3 ∆ICC 5.5   2.5 mA

Notes: For condition shown as Min or Max use the appropriate values under recommended operating conditions.

1. All typical values are at V

= 5 V (unless otherwise noted), Ta = 25°C.

CC

2. Measured by the voltage drop between the A and B terminals at the indicated current through the switch.

On-state resistance is determined by the lower voltage of the two (A or B) terminals.

3. This is the increase in suppl y current for eac h input that is at the specified TTL voltage level rather than V

or GND.

*1

Max Unit Test conditions

V

Ω

= 2.4 V, IIN = 15 mA

V

IN

Typ at V

V

= 2.4 V, IIN = 15 mA

IN

= 4.0 V

CC

One input at 3.4 V,
other inputs at V

or GND

CC

CC

(Ta = −40 to 85°C)

Capacitance

Item Symbol VCC (V) Min Typ Max Unit Test conditions

Control input capacitance CIN 5.0  3  pF VIN = 0 or 3 V
Input / output capacitance C
Note: This parameter is determined by device characterization is not production tested.

5.0  5  pF VO = 0 or 3 V, OE = VCC

I/O (OFF)

(Ta = 25°C)

Rev.1.00 Apr 07, 2006 page 3 of 6