®
It’s Under Control
It’s Under Control
U2
Weather Resistant Remote Control
®
Operation Guide
70-210036-19 V 1.1
1
U2
Weather Resistant Remote Control
Copyright © 2008
Remote Technologies Incorporated
All rights reserved.
2
It’s Under Control
FEDERAL COMMUNICATIONS COMMISSION NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including
interference that may cause undesired operation.
®
MMURTI1200
Canada IC = 3166A-RTI1200
117 612 914
DECLARATION OF CONFORMITY (DOC)
The Declaration of Conformity for this product can be found on the RTI
website at: www.rticorp.com/declaration
3
U2
Weather Resistant Remote Control
BATTERY DISPOSAL
Your U2 Weather Resistant Remote Control is shipped with nonrechargeable primary batteries. These batteries are generally
considered not to be environmentally hazardous. In most cases
they can be disposed of in normal household trash, but you
should always verify and follow your local regulations.
Do not burn or incinerate used batteries, as it may cause internal materials
to explode.
It is important not to dispose of large amounts of batteries in a group.
Used batteries are often not completely “dead.” Grouping used batteries
together can bring these “live” batteries into contact with one another,
creating safety risks.
SAFETY SUGGESTIONS
Read Instructions. Read all safety and operating instructions before
operating the unit.
Retain Instructions.
reference.
Heed Warnings. Adhere to all warnings on the unit and in the operating
instructions.
Follow Instructions.
Heat. Keep the unit away from heat sources such as radiators, heat
registers, stoves, etc., including ampliers that produce heat.
Object Entry.
openings.
Servicing.
operating instructions. Refer all other service needs to qualied service
personnel.
Damage Requiring Service.
service personnel when:
Objects have fallen into the unit.
The unit does not appear to operate normally or exhibits a marked
change in performance.
The unit has been dropped or the enclosure has been damaged.
Do not allow objects to fall into the enclosure through
Do not attempt any service beyond that described in the
Keep the safety and operating instructions for future
Follow operating instructions and instructions for use.
The unit should be serviced by qualied
4
It’s Under Control
LIMITED WARRANTY AND DISCLAIMER
Remote Technologies Incorporated warrants its products for a period of one
(1) year from the date of purchase from Remote Technologies Incorporated or
an authorized Remote Technologies Incorporated distributor.
This warranty may be enforced by the original purchaser and subsequent
owners during the warranty period, so long as the original dated sales receipt
or other proof of warranty coverage is presented when warranty service is
required.
Except as specied below, this warranty covers all defects in material and
workmanship in this product. The following are not covered by the warranty:
Damage resulting from:
1. Accident, misuse, abuse, or neglect.
2. Failure to follow instructions contained in this Guide.
3. Repair or attempted repair by anyone other than Remote Technologies
Incorporated.
4. Failure to perform recommended periodic maintenance.
5. Causes other than product defects, including lack of skill, competence or
experience of user.
6. Shipment of this product (claims must be made to the carrier).
7. Being altered or which the serial number has been defaced, modied or
removed.
Remote Technologies Incorporated is not liable for any damages caused by its
products or for its failure of its products to perform, including any lost prots,
lost savings, incidental damages, or consequential damages.
Remote Technologies Incorporated is not liable for damages based upon
inconvenience, loss of use of the product, loss of time, interrupted operation,
commercial loss, any claim made by a third party or made by you for a third
party.
Remote Technologies Incorporated’s liability for any defective product is
limited to repair or replacement of the product, at our option.
If your U2 Weather Resistant Remote Control needs service, please contact
Remote Technologies Incorporated by telephone, fax or E-mail for return
information. Please do not return products to Remote Technologies
Incorporated without return authorization.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated without the prior written notice of Remote
Technologies Incorporated.
The information contained in this document is subject to change without
notice. Remote Technologies Incorporated shall not be liable for errors or
omissions contained herein or for consequential damages in connection with
the furnishing, performance, or use of this guide.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other brands and their products are trademarks or registered trademarks of
their respective holders.
U2, Integration Designer™, and the RTI logo are registered trademarks of
Remote Technologies Incorporated.
®
5
U2
Weather Resistant Remote Control
6
It’s Under Control
TABLE OF CONTENTS
Federal Communications Commission Notice .............. 3
Battery Disposal ......................................................... 4
Safety Suggestions ..................................................... 4
Limited Warranty and Disclaimer .............................. 5
Table of Contents ....................................................... 7
Chapter 1 - Welcome .................................................. 9
Compatibility ........................................................... 9
Software Requirements ............................................ 9
Unpacking and Inspection ........................................ 10
Product Contents .................................................... 10
Chapter 2 - Introduction .............................................11
Features ................................................................ 11
Important Notes ..................................................... 11
Waterproof Note ..................................................... 11
Getting Started ...................................................... 12
Cleaning ................................................................ 12
Remote Reference ................................................... 13
Chapter 3 - Operation .................................................15
LCD Display ........................................................... 15
Control Panel Page .................................................. 16
Adjust Contrast ................................................... 16
Time Out ............................................................ 17
Tilt Switch........................................................... 17
Change Passcode ................................................. 18
Clear All ............................................................. 19
Low Battery Indicator ........................................... 19
Programming ...................................................... 19
Chapter 4 - Specications ........................................... 21
Chapter 5 - Troubleshooting ....................................... 23
Chapter 6 - Service and Support ................................. 25
Index .........................................................................27
®
7
U2
Weather Resistant Remote Control
8
It’s Under Control
CHAPTER 1 | WELCOME
Thank you for purchasing the U2 Weather Resistant Remote
Control. The U2 Weather Resistant Remote Control is designed for reliable
wireless control of audio/video systems from environments which are
too harsh for normal remote controls. It is completely sealed, making it
waterproof*. The U2 combines the convenience of eight programmable
“soft” buttons with an LCD display and the ideal selection of commonly
used keypad buttons. The high contrast display can be customized with any
combination of text and graphics desired. This provides a simple and exible
interface for operating today’s sophisticated electronic systems, regardless
of the location. The U2 Weather Resistant Remote Control is a perfect
companion for hot tubs, pools, bathrooms, and decks.
Used with RTI automation devices, the U2 Weather Resistant Remote
Control is capable of power sensing for reliable operation and RS-232
communications for advanced control. Sleek and durable, the U2 expands
your control to wherever your lifestyle requires.
COMPATIBILITY
The U2 Weather Resistant Remote Control is capable of radio frequency
output only and must be installed along with an RTI control processor and
RF antenna - it cannot deliver IR directly to devices. RTI control processors
and Integration Designer™ software are compatible with infrared (IR)
commands with carrier frequencies between 15KhZ and 460KhZ, as well as
those commands that do not use a carrier. This covers virtually all of the
remotes that exist to date.
®
SOFTWARE REQUIREMENTS
The recommended minimum system requirements needed to run the
Integration Designer™ software are as follows:
Windows 2000®, Windows XP® or later version.
A free USB port.
At least 256 Megabytes of RAM.
At least 250 Megabytes of free disk storage.
Screen resolution of 800x600 with 16-bit color.
Optional printer for printing reports.
9
U2
Weather Resistant Remote Control
CHAPTER 1 | WELCOME
UNPACKING AND INSPECTION
After unpacking your new U2 Weather Resistant Remote Control, save all
of the packing materials in case you ever have to ship the unit.
Thoroughly inspect the U2 and packing materials for signs of damage.
Report any damage to the carrier immediately. Report any equipment
malfunctions to Remote Technologies Incorporated or an authorized
Remote Technologies Incorporated distributor.
PRODUCT CONTENTS
Contents within the box include the following items:
One (1) U2 Weather Resistant Remote Control
One (1) mounting holster
Four (4) AAA batteries
One (1) operation guide
Two (2) wood screws
10
It’s Under Control
CHAPTER 2 | INTRODUCTION
FEATURES
The U2 Weather Resistant Remote Control provides superior quality and
reliability as well as these features:
Ergonomic design permits effortless, one-handed operation.
Durable design is waterproof.*
Mounting holster included for storage when not in use.
Thirty-three assignable/programmable keypad buttons.
Combines easy-to-read LCD display for custom buttons, text, and
graphics with eight programmable keypad buttons.
Tactile feedback on all buttons.
Transmits commands using RF for operation through walls, cabinets,
etc.
Optional ‘Voltage’ and ‘Video’ sensing modules to monitor power status
of equipment.
Optional interface for RS-232 controlled equipment.
Non-volatile Flash memory stores your system conguration even when
power is not present.
Field upgradable rmware.
System includes four AAA batteries.
USB Programming.
®
IMPORTANT NOTES
Please read these important notes about the U2 Weather Resistant Remote
Control:
The U2 performs optimally in temperatures between 40° F to 105° F. If
the temperature is too hot, the display appears dim. If the temperature
is too cold, the display appears dark and may respond slowly.
Do not subject the U2 to vibrations. The display may be damaged from
excessive shock or vibration.
Do not disassemble the unit - Do not remove the screws holding the
back cover of the U2. Service of the U2 Weather Resistant Remote
Control should be performed by authorized personnel only.
If the U2 is subjected to harsh chemicals such as chlorine or salt water,
rinse the remote in fresh water with mild detergent to prevent cosmetic
or other damage.
*WATERPROOF NOTE
The U2 Weather Resistant Remote Control is designed to withstand
temporary exposure to water only. Although it is safe to use in showers,
hot tubs, and pools, DO NOT ALLOW THE U2 WEATHER RESISTANT
REMOTE CONTROL TO REMAIN FLOATING OR SUBMERGED IN WATER FOR
AN EXTENDED PERIOD OF TIME. A mounting holster is provided for storage
when the U2 is not in use.
11
U2
Weather Resistant Remote Control
CHAPTER 2 | INTRODUCTION
GETTING STARTED
The following steps for initial installation including removing/
NOTE:
installing the battery door should be performed by an authorized service
center or trained installer only.
BATTERIES
Start by inserting four AAA batteries (included) into the battery
compartment. Make sure they are oriented properly. A polarity diagram is
molded into the bottom of the battery compartment.
IMPORTANT NOTE:
Lithium batteries be used as they provide a greater lifespan.
PROGRAMMING
Pull up the USB Programming Port Cover inside the battery compartment
to allow access to the USB programming port. Insert the USB cable into
the programming port and download the conguration le using the
Integration Designer™ software.
BATTERY COMPARTMENT DOOR INSTALLATION
If you are replacing old batteries, you will need to rst remove the seven
screws that hold the battery compartment door in place.
IMPORTANT NOTE:
THE TOP AND BOTTOM OF THE U2 TOGETHER.
ADDITIONAL NOTE:
DOOR, VERIFY THAT THE RUBBER BATTERY COMPARTMENT GASKET
AND USB PROGRAMMING PORT COVER ARE ALIGNED AND INSTALLED
PROPERLY.
In order to simplify the initial programming process, the U2 is shipped
without the seven battery compartment screws tightened. When tightening
these screws, make sure the pressure is evenly distributed around the
entire outer gasket. You should gradually tighten each screw, rotating
among them around the unit (similar to tightening the bolts on a spare
tire). Each screw should eventually be tightened rmly, but not over-
tightened.
The U2 is turned on by touching any keypad button. If the tilt sensor is
enabled, picking up the unit will also turn it on.
When replacing batteries it is recommended that
DO NOT REMOVE THE ELEVEN SCREWS HOLDING
PRIOR TO INSTALLING THE BATTERY COMPARTMENT
CLEANING
Occasional cleaning may be required, depending on use. To clean your U2,
lightly dampen a lint-free cloth with fresh water and mild detergent, and
wipe the display, keypad and outer surfaces. Rinse with fresh water.
12
CHAPTER 2 | INTRODUCTION
BACK
It’s Under Control
Battery
Compartment
Door Screws (7)
Battery
Compartment
Door
Battery
Compartment
Gasket
®
Battery
Compartment
USB Programming
Port Cover
Assembly Screws (11)
DO NOT REMOVE
USB Programming Port
(Cover Removed)
13
U2
Weather Resistant Remote Control
CHAPTER 2 | INTRODUCTION
FRONT
LCD
Display
Display “Soft”
Buttons
Page Navigation
Buttons
Backlight
Button
Home Page
Button
Keypad
Buttons
14
It’s Under Control
CHAPTER 3 | OPERATION
THE LCD DISPLAY
The U2 Weather Resistant Remote Control display is organized as a series
of pages and frames. A page consists of one to nine frames, and only one
frame is displayed on the screen at a time.
Normally each frame on a page contains objects (text, graphics, etc.) that
are related in some way. For instance, they may all display information
necessary for controlling a particular DVD player.
By default, the U2 has one Home page—all other pages are normally
accessed from links on the Home page. In addition, any button on any
page can contain a link to any other page when selected.
Normally the Home page is used to display the names of the equipment
being controlled. The U2 Weather Resistant Remote Control will support
200 pages including the Home page; each page can consist of up to 9
frames.
®
By default, pressing the HOME button at any time will return you to this
page. It is possible, however, to program the Home button to behave
differently if desired.
15
U2
Weather Resistant Remote Control
CHAPTER 3 | OPERATION
THE CONTROL PANEL PAGE
The Control Panel page can be displayed by holding down the backlight
button for three seconds.
You can also access the Control Panel page by assigning a “Control Panel”
page link to a button using the Integration Designer™ software.
The Control Panel consists of the following two frames:
To change frames, press the next page button below the display.
To return to the user program, press the Home button.
ADJUST CONTRAST
This selection displays a window that allows you to adjust the LCD
contrast. Press the Left Arrow or Right Arrow soft buttons to adjust.
Press either of the OK soft buttons to close.
16
It’s Under Control
CHAPTER 3 | OPERATION
TIME OUT
This selection displays a window that allows you to adjust the amount of
time the unit stays awake after the last button press. The time is variable
from 1 second to 60 seconds. Press the Left Arrow or Right Arrow soft
buttons to adjust the time.
Note: The default time out is 10 seconds, changing this time may shorten
the battery life of the U2.
Press either of the OK soft buttons to close.
TILT SWITCH
This selection displays a window that allows you to adjust the settings for
the built-in tilt switch. The tilt switch is a motion detector that turns the
remote on when activated.
On means the tilt switch is active and will wake up the U2 Weather
Resistant Remote Control when it is moved.
Off means the tilt switch is inactive.
Press either of the OK soft buttons to close.
®
17
U2
Weather Resistant Remote Control
CHAPTER 3 | OPERATION
CHANGE PASSCODE
This selection displays a window that allows you to set the passcode that is
used to limit access to the Clear All function in the Control Panel, as well as
the Secured property that can be assigned to any button.
When you select the CHANGE PASSCODE function, the screen will prompt
you to enter the old passcode using the numeric keypad buttons. Press the
ENTER keypad button after entering the numbers.
(The default code is 0000).
Now enter a new four-digit passcode.
You will be prompted to enter the new four-digit passcode again for
conrmation.
When new code is entered successfully, the “Code Changed” window will
pop up to let you know you have changed the passcode.
Do not forget the passcode!
18
It’s Under Control
CHAPTER 3 | OPERATION
CLEAR ALL
This selection displays a window that will allow you to erase the current
user program in the U2 Weather Resistant Remote Control. You will be
prompted to enter the current passcode. If the proper code is entered, the
entire user program in the U2 will be erased.
Warning! This will erase the entire user program in the U2. Once this is
done there is no way to restore it, except by reloading the program from
the Integration Designer™ software!
If you inadvertently select the CLEAR ALL function, simply press the ENTER
keypad button without entering the passcode and you will be returned to
the Control Panel page.
LOW BATTERY INDICATOR
If the U2 Weather Resistant Remote Control battery capacity is reduced to
approximately 25 percent, a low battery icon will appear in the lower left
side of the display:
At this point the U2 batteries should be replaced to maintain optimum
performance.
®
Low Battery Icon
PROGRAMMING THE U2 WEATHER RESISTANT REMOTE CONTROL
The U2 Weather Resistant Remote Control is programmed using RTI’s
Integration Designer™ software. RTI dealers can download the software
from:
www.rticorp.com/dealers
A PC running Windows® 2000 or higher with a USB port is required. The
required USB cable is included with the RTI IR-PRO dealer kit.
The U2 will not operate normally while connected to a PC’s USB
Note:
port. Make sure you disconnect it from the PC to navigate pages or
transmit commands. In addition, the U2 will not be able to sync with a PC’s
USB port while it is transmitting a command or running a macro.
19
U2
Weather Resistant Remote Control
20
It’s Under Control
CHAPTER 4 | SPECIFICATIONS
Power 4 - AAA batteries
Power Management Automatic On/Off (tilt switch)
Radio Frequency
Control Range
Radio Frequency
Carrier
Operating
Temperature
Display High-contrast STN Monochrome LCD
Display Size (H x W) 2.1 in x .94 in (53mm x 24mm)
Backlights White EL (Display and Keypad)
Total System
Memory
Device Capability Total number of devices is limited only by memory
Macro Capability Unlimited steps in a single macro
Communications USB programming port
Dimensions
(L x W x D)
Enclosure High-impact molded ABS plastic
Weight 7 oz. (200g)
Warranty One Year (Parts & Labor)
Up to 100 feet (30.5 meters)
with System Interfaces/Processors
433 MHz
+32° F to +122° F (0° C to +50° C)
128h x 64w pixels
256K Bytes Flash (non-volatile) memory
Total number of macros is limited only by memory
Macro capability on every button
9.1” (231mm) x 2.4” (61mm) x 1.0” (25mm)
®
All specications subject to change without notice.
21
U2
Weather Resistant Remote Control
22
It’s Under Control
CHAPTER 5 | TROUBLESHOOTING
If you are having problems with your U2 Weather Resistant Remote
Control, please read the information below before contacting technical
support.
If you continue to have problems, see Chapter 6 for more information on
contacting RTI technical support.
DISPLAY IS DIM, BLANK OR UNREADABLE
Make sure the batteries are inserted properly and are new. Try
adjusting the contrast level from the Control Panel page (Refer to
Chapter 3 for more details). By nature, the contrast of an LCD screen
changes with temperature, so if the remote is cold the display will be
dark and will return to normal as it warms.
USB COMMUNICATIONS PROBLEMS
Verify that your PC is running Windows® 2000 or higher.
Verify that the U2 Remote Control is present in the Human Interface
Devices section of the Device Manager within the Windows® Control
Panel.
Make sure you are using the programming cable that was supplied by
RTI and that both ends are connected securely.
Make sure the PC detects the presence of the U2 Remote Control. If it
doesn’t, unplug the USB cable, wait for about ten seconds, and plug it
in again.
If the download fails after some data has been transferred, try re-
sending the program.
®
CONTROL PROBLEMS
If you are using an RTI RF control system, look at the data light on the
RTI RF antenna - a green light denotes an RTI signal is being received,
while a red light means there is some interference blocking the signal.
Verify the USB programming cable is disconnected.
23
U2
Weather Resistant Remote Control
24
It’s Under Control
CHAPTER 6 | SERVICE AND SUPPORT
For news about the latest updates, new product information, and new
accessories, please visit our web site at:
www.rticorp.com
CONTACTING RTI
For general info, you can contact RTI at:
Tel. (952) 253-3100
Fax (952) 253-3131
info@rticorp.com
RTI TECHNICAL SUPPORT
At RTI, customer service and satisfaction is an utmost priority. If you are
encountering any problems or have a question about your RTI product,
please contact RTI Technical Support for assistance.
RTI provides technical support by telephone, fax or e-mail. For the highest
quality service, please have the following information ready, or provide it in
your fax or e-mail.
Your Name
Company Name
Telephone Number
E-mail Address
Product model and serial number (if applicable)
If you are having a problem with hardware, please note the equipment in
your system, a description of the problem, and any troubleshooting you
have already tried.
If you are having a problem with software, please note what version you
have installed, the operating system on your PC, a description of the
problem, and any troubleshooting you have already tried.
If you are calling about a software or programming question or problem,
please be at you computer when you place your call. This will considerably
speed up the troubleshooting process.
For technical support or assistance with your U2 Weather Resistant Remote
Control, software, or accessories, contact RTI at:
(952) 253-3137
support@rticorp.com
www.rticorp.com
For questions regarding service or repair of your U2 Weather Resistant
Remote Control, contact RTI at:
(952) 253-3136
service@rticorp.com
www.rticorp.com
Please do not return products to RTI without return authorization.
®
25
U2
Weather Resistant Remote Control
CHAPTER 6 | SERVICE AND SUPPORT
Shipment of U2 Weather Resistant Remote Control for Service
RTI will pay all labor and material expenses for all repairs covered by this
product’s warranty. If necessary repairs are not covered by warranty, or if
a unit is examined which is not in need of repair, you may be charged for
the repairs or examination.
If it is necessary to ship the U2 Remote Control for service:
Please pack it securely (we suggest that it be insured).
Do not include accessories such as power cords or manuals unless
instructed to do so.
You must pay any shipping charges incurred in getting your U2 Weather
Resistant Remote Control to RTI. RTI will pay reasonable return shipping
charges via a carrier of our choice to any destination within the United
States if the repairs are covered under warranty.
A copy of the original dated sales receipt must be provided whenever
warranty service is required. You will need this receipt to establish the date
of purchase.
26
It’s Under Control
INDEX
Battery Disposal ................................................................. 4
Table of Contents ................................................................ 7
Features .......................................................................... 11
Federal Communications Commission Notice ..........................3
Introduction ..................................................................... 11
Important Notes ............................................................
Waterproof Note ............................................................
Cleaning ...................................................................... 12
Getting Started ............................................................. 12
Remote Reference ......................................................... 13
Limited Warranty/Disclaimer ................................................ 5
Operation ........................................................................ 15
Adjust Contrast ............................................................. 16
Change Passcode .......................................................... 18
Clear All ....................................................................... 19
Control Panel Page ........................................................ 16
LCD Display .................................................................. 15
Low Battery Indicator .................................................... 19
Programming ................................................................ 19
Tilt Switch .................................................................... 17
Time Out ...................................................................... 17
®
11
11
Product Contents .............................................................. 10
Safety Suggestions ............................................................. 4
Service and Support ......................................................... 25
Contact RTI ..................................................................
Shipment for Service .....................................................
Technical Support ..........................................................
Specications ................................................................... 21
Troubleshooting ................................................................ 23
25
26
25
27
U2
Weather Resistant Remote Control
It’s Under Control
Remote Technologies Incorporated
5775 12th Avenue East, Suite 180
Shakopee, MN 55379
Tel: 952-253-3100
Fax: 952-523-3131
www.rticorp.com
®
28
© 2008 Remote Technologies Inc. All rights reserved. Printed in Taiwan.
Loading...