Remote Technologies BDSV3 - N, BDSV3 User Manual

BDS

The Remote Audio BDS (Battery Distribution System)
has been the standard power management system in
ENG audio bags for over a decade. Once considered a
luxury, the ability to power multiple pieces of audio
equipment with a single rechargeable battery is now a
necessity as equipment demands become more
complex. The BDS system accommodates this need with
a reliable, convenient, and robust design.

Description

Remote Audio's BDS system consists of a reverse­polarity protected and overload protected distribution box
with on/off switch, six outlets, power source (typically a
rechargeable battery such as the NP-1), an input cable,
and output cables for the devices being powered. The
primary purpose of the BDS system is to simultaneously
turn on and off multiple pieces of equipment being
powered by a single source. For this basic function, the
BDSv3/BDSv3-N may be used exactly like the older
BDSv2 that it replaces. The input and output connections
are the same, so all former BDS input and output cables
made by Remote Audio are compatible with the
BDSv3/BDSv3-N. The capacity of the box is limited to 5
Amps.

v3

/ BDS

v3 - N

REMOTE AUDIO

220 Great Circle Road, Suite 114, Nashville, TN 37228-1737

The BDSv3* design takes the system to a new level of
refinement and functionality with the addition of an
optional 6-pin connector for the RM (remote meter)
accessory. The RM can turn on and off the BDSv3
remotely, and can display the voltage of the power source
and the amperage draw of the equipment. The BDSv3
can be used without the RM remote meter. In this case,
the toggle switch turns the unit on and off.
When turned on, the switch illuminates.

*The BDSv3-N does not include an RM port, but is upgradable
via Remote Audio.

Using the BDSv3 with the optional RM remote meter

When connected to the RM remote meter, and the BDSv3
toggle switch is in the OFF position, the RM controls the
on/off circuit of the BDSv3. This allows the BDSv3 box to
be placed deep in the bag, out of the way. To turn the
BDSv3 on or off with the RM, press and hold both buttons
of the RM for three seconds. When on, the RM will
display the voltage of the power source. Pressing the
lower button (labeled "AMPS") will display the current
draw of the devices being powered for as long as the
AMPS button is pressed. If the BDSv3 toggle switch is in
the on position, the RM will not turn off the BDSv3. In this
case, the on-off function of the RM will only turn on and
off the meter display.

Connectors and cables

The outlet connectors on the BDS box are a special
switching type that requires a long shaft mating plug with
a 2.5mm hole. This connector set was chosen for its
strength and so that unused (exposed) outlets on the box
are not active until a cable with the proper mating
connector is plugged into it, helping prevent accidental
short circuits. Output cables by Remote Audio are
manufactured specifically for use with the BDS, and come
with unique low-profile right angle locking connectors.
Therefore, it is recommended that only Remote Audio
brand output cables be used with the BDS system. The
polarity of the outlets is "center positive". "Y" cables are
available for connecting more than six devices. Input
cables, battery adapters and AC-DC adapters by
Remote Audio are also available.

Phone: [phone] | Fax: [phone]

www.remoteaudio.com

The input connector on the BDS box is a common TA4M
(miniature 4-pin male XLR) with the standard scheme of
"pin-1 NEG, pin-4 POS". To improve reliability and reduce
voltage drop, the contacts are doubled 1-2 and 3-4 at the
circuit board. Therefore, if the user wires their own input
cables, it is recommended to connect pins 1-2 and 3-4.
The power indicator built into the BDS box switch can be
used to confirm proper polarity of the input cable
(if it illuminates, the polarity is correct).

Rev. 11/10

BDS

The orange ring… Switch vs Unswitched.

Outlet #1 can be either "switched" or "unswitched".
"Switched" means that the outlet turns off and on.
"Unswitched" means that the outlet is always on when
power is present. The factory default for outlet #1 is
"unswitched", as indicated by an orange ring. This
feature is often desired for the audio mixer. For example,
in this configuration, when only the mixer and boom mic
are needed, turning off the BDS box will turn everything
off (receivers, etc.) except for the mixer.

This can be a convenient way to turn off everything that
is not needed, extending the life of the battery. The status
of outlet #1 can be easily reversed to "switched" by
opening the BDS box and moving a jumper from the
unswitched position to the switched position as labeled
on the circuit board. No soldering is required to make this
change. Care must be taken to not over-tighten the
outlet connector nut when replacing the orange ring.

Short circuit and overload protection

The BDS box has auto­resetting protection against
output short circuits and loads
in excess of 5 amps, with each
outlet capable of handling up
to 3 amps each. If the BDS
fails to pass power, it could be
due to an overload or a short
circuit. In the case of a short
circuit of an individual output
cable or piece of gear, only
that outlet's breaker will trip,
protecting the other connected
gear from damage. If a piece
of gear fails to power up, that
output cable should be
checked for continuity with a

multimeter (shorted or open conductors), or replaced
entirely. The BDS box will also protect itself when
connected to loads of over 5 amps, and the on/off toggle
switch will no longer be illuminated. However, it is very
rare for field audio bags (the primary intended use for the
BDS) to have current draws in excess of 5 amps. Using
the optional RM (Remote Meter) with the BDSv3 will take
the guesswork out of calculating the amperage draw of
your system.

v3

/ BDS

v3 - N

5A global maximum

3A

3A

3A

3A

3A

3A

Reverse polarity protection

As a protective feature for devices being powered, in the
event that an input cable or battery adapter is miswired,
the BDSv3 will not pass reverse polarity voltage to its
outputs. Unlike some reverse polarity protection circuits,
the BDS circuit does not cause a voltage drop during
normal operation.

Noise and shared power systems.

Thousands of satisfied field audio professionals are using
the BDS system to power their equipment. However, it is
possible to have unwanted audible noise induced into
audio systems by a common (shared) power source. To
optimize your system, it is recommended to use line level
signals instead of mic level signals whenever practical.
Also, turn phantom voltage off of all preamp inputs that
are connected to non-microphone devices. If noise is still
heard, to determine the cause, unplug one device at a
time from the BDS box, noticing any change in noise
associated with the removal of each device. If the noise
goes away after unplugging a particular device, try
powering that device with a separate battery. If using a
separate battery causes the noise to go away, then the
problem is a ground loop associated with the combination
of a common power source and audio grounding
schemes. Be aware that this noise will not be removed
with "L/C" filters found in some distribution boxes. To
remove the noise, here are four options for interrupting
the ground loop: 1) Use a separate battery for the
offending device. 2) Try different grounding/floating
schemes with the audio cables. 3) In devices that use a
single 9V battery, use an isolating 9V battery eliminator
such as made by Lectrosonics (isolating AA eliminators
should soon be available). 4) Use a power isolator cable
such as the Remote Audio Juicer cable
(30 watts max, but a bit large for bag use).

Mounting clip

The BDSv3 box comes with a stainless steel clip to aid in
securing the box to a bag or strap. Additional holes on the
box are available for positioning the clip in the opposite
direction. NOTE: Keep the original clip screws. Attaching
the clip with screws longer than those originally supplied
can damage the BDS box and void the warranty.

Repairs

Items needing repair may be sent directly to:
Remote Audio Products
220 Great Circle Road, Suite 114
Nashville, TN 37228.
Prior to returning any items, contact Remote Audio for an RA# (return
authorization number) at 615-256-3513, or [e-mail]

REMOTE AUDIO

220 Great Circle Road, Suite 114, Nashville, TN 37228-1737

Phone: [phone] | Fax: [phone]

www.remoteaudio.com

Limited Warranty

For a period of 1 year (for the BDSv3 box), or 6 months (for BDS cables) from the time of sale, defects in parts and workmanship will be either

repaired or replaced at the determination of Remote Audio. Dated proof of purchase required.

Rev. 11/10