in71TVI3N2D Series
Indoor Outdoor Bullet Camera
Quick Start Guide
Before operang this product, please read this quick-start guide to ensure proper use.
Please store these instrucons a safe place for future reference.
FEATURES
• IP68 Die Cast Aluminium Housing
• Varifocal lens
• High Resolution TVI (1080) Analog
(1000TVL)I
• 0 Lux IR on, 0.01 Lux
• Wide Dynamic Range
• Wire Management Mount
• Sun Shield
• HLM, BLC, DEFOG
• Sens Up
• On Screen Menu
• 3 Axis gimbal
• 12VDC/24VAC Powered
PRECAUTIONS
1. Before installing and operang the unit, please read this manual carefully.
2. Precision components are contained in this camera, please avoid violent vibraons during
installaon and maintenance. Do not connect the power unl you have completed the
installaon.
3. Please obey all local electrical wiring regulaons when using this unit.
4. Do not use abrasive or corrosive materials for cleaning. Use only a so cloth for cleaning.
5. To prevent damage to the lens or sensor, do not point the camera directly into the sun
or very strong light sources.
6. Do not use the camera outside it’s working temperature (-10°C~ 50°C / 14°F ~122°F) or
humidity (<90%) ranges.
7. Ensure that the power supply meets the current requirements of the camera and that
the supply voltage is inside the tolerances of the camera: 12vdc or 24VAC ±10%
8. Ensure that the xings used are adequate to support the load of camera.
9. In case of camera failure, do not aempt to dismantle or service the camera yourself.
Please refer to qualied service personnel for repair of the camera.
CONNECTIONS
1. Analog Video (Yellow) BNC Connector.
2. TVI Video (Black) BNC Connector
3. Power Input connector. This is a 2 pin non-removable terminal screw connector.
Observe polarity of 12VDC connecons. 24VAC power is not polarity sensive.
Refer to the diagrams below for claricaon.
4. Thumb screw to aached Sun Shield
5. Sun Shield
6. Service Port for Analog Video
7. Focus Screw (Far:Near) Zoom Screw (Wide:Telephoto)
8. Service Cable
+ (Pos)
- (Neg)
When the OSD menu is launched, you are
presented with the adjacent opening screen.
A menu opon followed by a indicates the
presence of a sub-menu. Options set to OFF will
not show a until set to ON
Use RETURN to return to the previous menu.
EXPOSURE menu:
• SENS-UP - Select Off to 8x to enhance low
light performance. Slows frame rate and
increases low light sensitivity. When on
shutter cannot be selected
• BRIGHTNESS - Sets the level of the overall
brightness
• SHUTTER - Auto, Manual selection,
1/30~1/60K. Set this on to reduce the
exposure time of each image. This can be used to reduce blur in images with fast
changing content.
• AGC- Level Control -Used to adjust overall gain
WHITE BALANCE - AUTO, AUTO-EXT ,
PRESET, MANUAL
• AWB -AUTO (default) The camera
automatically samples the image for
optimum white balance
• AUTO EXT - The camera automatically
samples the image for optimum white
balance in an exterior environment.
• PRESET - Allows the white balance to
be set automatically and locked.
This option is normally used when no
white reference is present in the image. To set the white balance, hold a white
object in front of the camera, with light from the source falling on it and press
the joystick to set and lock the white balance
MANUAL - This option allows a selection of color temperature, Red and
Blue gain to be manually set in the image. Note, using this option requires care
to ensure all cameras on one system have the same color response.
SHARPNESS - Level Control
DEFOG - Used to help improve the
captured image in poor weather
conditions such as smog, fog, or smoke.
It automatically controls contrast ratio
by spatially analysing the histogram
characteristics
D-ZOOM - 0~127 Steps
Rev 0.1
MAIN MENU
EXPOSURE
WHITE BALANCE
AUTO
IMAGE.
BACKLIGHT
OFF
DAY&NIGHT
DNR MIDDLE
MOTION OFF
SERIAL
SPECIAL
SYSTEM
EXIT
EXPOSURE
SENS-UP OFF
BRIGHNESS
LENS MANUAL
AE MODE NORMAL
SHUTTER AUTO
AGC
DOUT SCALE COMP
RETURN
EXPOSURE MENU
IMAGE MENU
OSD MAIN MENU
LENS MENU
To set lens to correct eld of view and focus remove the access plug on the boom of the
camera. See image below. First plug your service cable into the service port ⑥ then into
your monitor. The eld of view may then be adjusted by turning the zoom lever, ⑦, and
moving until the required field of view is obtained. Next turn the focus lever ⑦ and adjust
to obtain optimum focus. When complete screw the access port onto camera to mainan
water seal.
MOUNTING
1. Mark and drill the three mounng holes for the base. Choose an appropriate drill bit for the
surface you are drilling in to and ensure that the diameter is correct for the xings being
used. Mark and cut/drill a central 20mm (¾”) diameter hole for the cable and connectors.
2. Use appropriate screws and wall plugs for the mounng surface in use.
3. Ensure that the xings can adequately bear the weight of the camera.
4. Make the video and power connecons and commission the camera.
LENS AND POSITIONING
The bullet camera has an integral varifocal lens, a OSD buon and Service port (adjusted from
the access port on boom of camera) along with a 3-axis mount which can be manipulated to
posion the camera.
To posion the camera to give the required image content, gently loosen the hex screws located
on the main mount to adjust fro pan, lt , azimuth , gently turn to reach desired posion then
reghten.
MAIN MENU
EXPOSURE
WHITE BALANCE
AUTO
IMAGE.
BACKLIGHT
OFF
DAY&NIGHT
DNR MIDDLE
MOTION OFF
SERIAL
SPECIAL
SYSTEM
EXIT
IMAGE MENU
SHARPNESS 6
DEFOG
OFF
D-ZOOM. 0
MIRROR
OFF
FLIP
OFF
FREEZE OFF
PRIVACY OFF
SHADING
OFF
COLOR GAIN
ACE OFF
RETURN
• MIRROR - Horizontal flip of image
• FLIP - Vertical flip of image
• FREEZE - Video can be stopped
• PRIVACY - Select up to 15 regions
• SHADING -Compensates for the dark
area created by the outline of the
lens. Compensation uses 2D gain
table. Users can control 0 ~ 100%
compensation rate according to
shading weight
• COLOR GAIN - Level control
• ACE - Adaptive contrast enhancer,
preserves fine details, reduces artifacts and loss of local contrast in the
image areas of bright/dark
BACKLIGHT, HLM, BLC, WDR
HLM -is the ability to reverse bright points
to black or gray, (areas such as headlights,
any high luminance areas) this function
will improve the overall picture.
BLC -Backlight compensation, when there
is strong backlight behind the object, clear
image of the background as well as the
object can still be obtained by using BLC
function
WDR -Wide dynamic range, improved
image by a fusion of high speed shutter of
image in light area and low speed image of
dark area
DAY/NIGHT - AUTO, COLOR, B/W, EXT
• AUTO - Allows the camera to switch
from color to B/W mode in low light.
The switching thresholds and hysteresis
time are adjustable.
• COLOR - Fixes the camera in color mode
• B/W - Fixes the camera in monochrome
mode.
• Ext - select this when color is controlled
by cds sensor
•
DNR - OFF, LOW, MIDDLE, HIGH
• This function is used to improve the picture quality by filtering the noise
which is generated under low light conditions
MOTION - Function of motion can designate the
range of the user to detect movement on the
screen and adjust the size of the area. So you
can monitor movement of an object on the given
region more efficiently
• MOTION ZOOM - Digital Zoom when
motion is detected 0~99
• SENSITIVITY- Level Control
• TARGET SIZE - Level Control 0~255
• AREA -Select area to apply motion
SERIAL
• CAMERA ID - 0~255
• CAMERA ID - On/Off
• Baud Rate - Selection
SPECIAL -
• Y GAIN- Level Control
• Cb GAIN - Level Control
• Cr GAIN- Level Control
• BURST GAIN-Level Control
SYSTEM -
• DEFECT DET -
Cover lens select on,adjust left and right press
Set to start mode
• GAMMA - Level selection
• DVR SELECT - Select DVR company
• OUTPUT MODE- Select 1080P, 720P, 720
crop
• CVBS- Select NTSC or PAL
• FRAME RATE- Set for 30 NTSC or 25 PAL
• LANGUAGE - Selection
• FOCUS ADJ - Green box means of focus, when gone in focus, left box low
contrast area, right box high contrast area
• FACTORY SET -Default to factory settings
• RETURN
System NTSC
Imaging Sensor Mega Pixel Sensor
Resoluon TVI (1080P) ANalog (1000TVL)
Sensivity 0.01Lux
Wide Dynamic Range Yes
S/N Rao 52dB
Day / Night Mechanical
Lens Focal Length 2.8~12mm
IR LED’s 6 Super LED’s
Eecve Range 100
Funcons OSD Multiple Languages
Shuer 1/50~1/60,000
Wide Dynamic Range Yes
DEFOG Yes
AGC Adjustable Level
SENS UP Adjustable Level
Electronic shuer Yes
Sync Internal
Camera ID Number O/On 0~255
White Balance Auto, Autoext, Preset, Manual
DNR Low, Medium, High
Gamma 0.45, 0.5, 0.55, 0.6, 0.65
Moon Detecon Yes
Digital Zoom Yes
Privacy masking O/On , Areas, Color, Posion
Image funcons Sharpness, Mirror, Defog, HLM, BLC,
D-Zoom, Shade Comp
Input/Output Video Output TVI BNC
CVBS 1.0Vp-p 75Ω - BNC
CVBS 1.0Vp-p 75Ω - Service port
Programming interface On board joysck
Power D Model 12VDC/24VAC ±10% 7W max
Physical Construcon Die Cast
Dimensions (mm) 255 x 125mm x 87
Weight 998g (2.2lbs)
Mounng Surface
Environmental Operang Temperature -10°C~+50°C
Humidity Less than 90%, non condensing
Order Codes Lens 2.8~12mm
in71TVI3N2D28V12
Remote Alert
519 Bennet Lane
Suite 101
Lewisville, Texas 75057
214-960-4564
Please visit our website for full informaon: www.remotealert.com
SPECIAL
Y GAIN
105
Cb GAIN
85
Cr GAIN 118
BURST GAIN 128
RETURN
SPECIFICATIONS
DAY/NIGHT
MODE AUTO
RETURN
DNR
SERIAL
BACKLIGHT
MOTION
SYSTEM
DEFECT DET OFF
GAMMA .55
DVR SELECT HKVISION
OUTPUT MODE 1080P
CVBS NTSC
FRAME RATE 30
LANGUAGE ENG
FOCUS ADJ OFF
FACTORY SET ON
RETURN
BACKLIGHT
SERIAL
CAM ID 0
ID DISPLAY OFF
BAUD RATE 9600
RETURN
IMAGE MENU
SHARPNESS 6
DEFOG
OFF
D-ZOOM. 0
MIRROR
OFF
FLIP
OFF
FREEZE OFF
PRIVACY OFF
SHADING
OFF
COLOR GAIN
ACE OFF
RETURN
MAIN MENU
EXPOSURE
WHITE BALANCE
AUTO
IMAGE.
BACKLIGHT
OFF
DAY&NIGHT
DNR MIDDLE
MOTION OFF
SERIAL
SPECIAL
SYSTEM
EXIT
BLC
BLS OSD OFF
H-POS 5
V-POS 6
H-SIZE 8
V-SIZE 5
RETURN
HLM
LEVEL
MODE NIGHT ONLY
RETURN
WDR
WEIGHT MIDDLE
RETURN RET
DAY&NIGHT
AUTO
AGC THRS
AGC MARGIN
DELAY AUTO
RETURN
EXTERN
ANTI-SAT
CDS D>N 100
CDS D<N 150
DELAY LOW
RETRUN
MOTION
MOTION ZOOM 0
SENSITIVITY
TARGET SIZE 20
AREA 9
RETURN
SYSTEM
SERIAL
Loading...