Remington R-843, Titanium MicroFlex 400 R-843, Titanium MicroFlex 400 R-842, Titanium MicroFlex 400 R-845 Use And Care Manual

®

®

MC

Use and
Care Guide

R-842
R-843
R-845

CS27830_R-845_series_IB 6/20/05 3:41 PM Page 1

3

When using an electrical appliance,
basic precautions should always be
observed, including the following.
Read all instructions before using
this appliance.

DANGER

To reduce the risk of electric shock:

■ Do not reach for an appliance that

has fallen into water. Unplug it
immediately.

■ Do not place or store this appliance

where it can fall or be pulled into a
tub or sink while it is plugged in.

■ Except when charging, always

unplug this appliance from the
electrical outlet immediately

after using.

■ Unplug this appliance before

cleaning it.

■ Do not use an extension cord
or a voltage converter with this
appliance.

■ Never drop or insert any object into
any of the appliance’s openings.

■ Do not use outdoors or operate
where aerosol (spray) products are
being used, or where oxygen is
being administered.

■ Always store this appliance and
cord in a moisture-free area.
Do not store it in temperatures
exceeding 140°F (60°C).

■ Do not plug or unplug this appli­ance when your hands are wet.

SAVE THESE INSTRUCTIONS

■ Do not wrap the cord around the
appliance.

■ Always attach the plug to the
appliance, then to the outlet. To
disconnect, turn all controls to
OFF, then remove plug from outlet.
Detach removable power cords
from appliances for storage.

■ Do not use this appliance with
a damaged or broken screen or
cutters, as injury may occur.

WARNING

To reduce the risk of burns, fire,
electric shock or injury to persons:

■ This appliance is for household
use only.

■ An appliance should never be left
unattended when it’s plugged in,
except when charging a recharge­able appliance.

■ Close supervision is necessary
when this appliance is used by,
on, or near children or invalids.

■ Use this appliance only for its
intended use as is described in
this manual. Do not use attach­ments not recommended by
manufacturer.

■ Keep the cord away from heated
surfaces.

■ Never operate this appliance if it
has a damaged cord or plug, if it
is not working properly, if it has
been dropped or damaged, or if it
has been dropped into water. If
any of these things happen, return
the appliance to an authorized
service center for examination
and repair.

IMPORTANT SAFETY

INSTRUCTIONS

2

Contents

English ..............................1

Spanish ...........................13

French .............................25

CS27830_R-845_series_IB 6/20/05 3:41 PM Page 2

Shaver Parts
(A) Head & cutter assembly
(B) ON/OFF button
(C) Locking bar
(D) Charging indicator
(E) Power port
(F) Trimmer button
(G) Head guard
(H) Cleaning brush
(I) Storage pouch (Model R-845)

4

Product Features

5

(B)

(D)

(F)

(I)

(G)

(A)

(H)

R-842 Rechargeable X X
R-843 Rechargeable X X
R-845 Rechargeable X X

Worldwide

voltage

Power system

Rinseable

Charging
Indicator

Light

Which model is yours?

Easy-View®Trimmer

Power System

■ Corded shavers can only be used while
they are plugged into an electrical outlet.

■ Rechargeable shavers can only be used
without the cord.

■ Cord/cordless rechargeable shavers can
be used with or without the cord. They
do not recharge during use, however,
and frequent corded use will result in
reduction of battery life.

Charging Indicator Lights

The charging indicator is a green light that
glows when the shaver is charging or fully
charged.

Worldwide Voltage

Your shaver can be used almost anywhere
in the world, because it has automatic dual
voltage conversion,

providing AC current

between 100-240

volts AC, 50-60 Hz. Just
plug it into the local outlet (you may need
an adapter plug) and use it as usual.

(C)

(E)

CS27830_R-845_series_IB 6/20/05 3:41 PM Page 4

To Tr im

To use the Easy-View

®

pop-up trimmer, simply
push the trimmer button
up. The trimmer will pop­up for use. Hold the
shaver as shown in the illustration. To
conserve battery energy (on rechargeable
shavers only), it is recommended to use the
trimmer only when needed for trimming.
When through using, push the trimmer
button downward to lock into the off
position.

Trim Sideburns

Simply touch the comb­edge of the trimmer to
the desired line for neat,
clean sideburns.

Trim Mustache

Hold shaver at desired
trim line for a quick, easy,
professional trim. The
trimmer can also be used
to trim the upper edge of
your mustache.

■ Always keep the protective head guard

on the cutter head and keep the trimmer
in the “off”position when the shaver is
not in use. The head guard must be put
on with the rear tab to the back of the
shaver.

For a Better Shave…

To help maximize your shaver’s perform­ance, consider using the Remington

®

Pre-Shave Powder Stick (SP-5). Just
rub over your beard. It absorbs moisture
and facial oils, helping set up the hairs so
they enter the cutting chamber more easily.
It makes shaving quicker and more
comfortable.

Getting a Close, Comfortable Shave

Congratulations on your purchase of
a premium Remington®shaver.The
MicroFlex®400 has Revolutionary
Titanium Shaving Technology.

Removing the Headguard

Before operating your shaver, remove the
headguard, which protects the screen and
cutter assembly. It is important to remove
the headguard correctly to avoid damaging
the clips that hold it to the shaver.

1. Press lightly on the top of the headguard.

2. Lift the lower rear edge.

3. Pull the headguard away from the

shaver.

! Always keep the protective head guard on

the shaver head and keep the trimmer in the
OFF position when the shaver is not in use.

ON/OFF Switch

To activate the shaver, press in the locking
bar while pushing the power button up.

Charging the R-842, R-843,
and R-845

Before using your shaver for the first time,
put it on charge for 24 hours.

To charge your shaver:

■ Slide the power button downward to the
OFF position.

■ Connect the supplied AC power cord to
the shaver’s power port and then to an
electrical outlet.

■ Your shaver cannot be overcharged, so
you can leave it plugged in and charging
between shaves.

Always use a clean, dry
shaver. Make sure that
the cutter head assembly
is in the locked position.

Wait at least 15 minutes
after getting up before
shaving, to ensure the
face is free of puffiness
that may be present from
sleeping.

Make sure your face is
clean and dry before
starting.

To Shave

Push the on/off button to
activate the shaver for
shaving.

The MicroFlex

®

needs no
adjustments to the heads
or cutters before you
shave. The floating heads
will automatically adjust
to the contours of your
face. It is not necessary
to apply pressure while shaving let the
shaver glide lightly on your skin. This gentle
touch makes shaving easier and helps
avoid possible skin irritation.

Use short, circular strokes.
Use your free hand to
stretch your skin. This
encourages your whiskers
to stand out, making it
easier for them to enter
the cutting chamber.

7

6

How To Use

■ To preserve the life of the batteries,
allow them to fully discharge every six
months, then recharge them for 24
hours.

! Rechargeable shavers like the R-842,

R-843, and R-845 are designed for cord­less operation only. Plugging them in will
not provide the power to shave.

Operating the Easy-View

®

Trimmer

The Easy-View®pop-up trimmer extends to
trim mustache, sideburns, etc.

■ Trimmer is turned off until it is extended
for use.

■ Push the trimmer button up to pop up
the trimmer.

■ Hold the shaver with the trimmer toward
you when trimming.

■ After trimming, pull the trimmer button
downward into the OFF position. Leave it
in the down position when not in use.

Adjusting to your new shaver

As with every shaver, your shave will
improve over time. So allow about three
weeks to develop an effective shaving style
and for your beard to adjust to the new
shaver.The adaptation period may take a
little longer if your skin is sensitive, or if
you alternate between shaving methods.

The Best Technique

It’s simple to get a great shave from your
new shaver. Here are a few tips for getting
the closest shave possible:

6

12

9

3

CS27830_R-845_series_IB 6/20/05 3:41 PM Page 6

To assure smooth, efficient performance, it
is important to clean your shaver.

Daily

Brush inside the head
assembly after each use:

1. Turn the shaver off.

2. Grip the head assem-

bly by the

three ridges

and pull it off the shaver.

3. Use the cleaning brush

to sweep out the internal
part of the head
assembly and the hair
pocket area, where 3
shaver

spindles are

located.

4. Replace head assem-

bly.

Weekly

Clean under the cutter
assembly at least once a
week:

1. Turn the shaver off.

2. Open the head

assembly as above.

3. Unscrew the center screw knob to

remove the cutter retainer assembly.

4. Use the cleaning brush to sweep the dust

and hairs from under the cutters.

5. Replace head assembly.

8

9

Cleaning & Maintenance

Lubricate

Remington®Shaver Saver®Lubricant (SP-4)
lubricates and cleans your shaver's cutters
and head assembly.The lubricant helps
remove hair clippings while reducing wear.
A quick spray after each shave keeps

your

shaver operating at peak performance.

Cleaning Cautions

■ The construction of this shaver is for
dry operation only. It is not water­proof. Never put the shaver in part or
completely into water.

■ Never clean the shaver or replace the
cutters while it is plugged into an
electrical outlet.

■ Do not use an aggressive cleansing
agent as this may destroy the shaver
coatings.

■ Do not clean or remove the head assem­bly while the shaver is running or plugged
in, as it may cause damage to the unit's
heads or cutters.

■ Replace worn or damaged parts with
Remington

®

replacement parts only.

Head/frame
assembly

Floating
cutter
heads

Locating pins

Cutter retainer
assembly

Center
screw
knob

Locating holes

! Important: Make sure to align the two

locating holes in the Cutter Retainer
assembly with the pins in the Head Frame
Assembly. (See illustration below).Then
tighten center screw knob to lock the
cutters into place.

Replace head assembly on the shaver
simply by pushing it onto the shaver.

Cover shaver head with plastic headguard
between uses. When removing the head­guard or placing it back onto the shaver,
do not apply pressure to floating cutter
surfaces, as you may damage them.

When is it Time to Replace
Your Heads and Cutters?

It is very important to replace your
heads and cutters when necessary to
ensure a close, comfortable shave with­out irritation. We recommend they be
replaced every 12 months. Here are
some signs of head and cutter wear,
indicating that replacement is needed.

Irritation

As the heads get excessively worn you may
experience some skin irritation. This would
be especially noticeable when you apply
after-shave lotion.

Pulling

When the cutters wear you may feel a
sense of pulling and a loss of closeness
when you shave. This is an indication that it
is time to replace your heads and cutters.

The replacement parts for your shaver is
model SP-19.

U.S. residents: To order, contact
us at 800-736-4648, visit us at
www.remington-products.com or visit
your local retailer.

Canadian residents:
To order shaver accessories, please
call 800-268-0425 or visit us at
www.remington-products.com

CS27830_R-845_series_IB 6/20/05 3:41 PM Page 8

MERCHANTABILITY, ARE LIMITED IN
DURATION TO TWO YEARS FROM DATE
OF ORIGINAL PURCHASE.

This warranty gives you specific legal rights
and you may also have other rights which
vary from state to state or province to
province. Some states do not allow the
exclusion or limitation of incidental, special
or consequential damages.

Performace Guarantee

Spectum Brands, Inc.

Money-back Offer

If within 30 days after you have purchased
your Remington

®

branded product, you are
not satisfied and would like a refund, return
it with the sales slip indicating purchase
price and date of purchase to the retailer
from whom it was purchased. Spectum
Brands, Inc. will reimburse all retailers who
accept the product within 30 days from the
date of purchase. If you have any questions
concerning the money-back guarantee,
please call

800-736-4648.

KEEP ORIGINAL SALES RECEIPT AS PROOF
OF PURCHASE FOR WARRANTY PURPOSES.

100-240 VAC 50/60 Hz

Questions or comments:

Call 800-736-4648 in U.S. or
800-268-0425 in Canada.
Or visit www.remington-products.com

REMINGTON & MICROFLEX are trademarks
of ROVCAL, INC.
© 2005 ROVCAL, INC.
06/05 Job #CS27830
U.S. Patents: D486,942:5,390,416; 5,408,749
Canadian Patents: D100892: 2,091,039;
2,114,923; 2,111,626
Spectum Brands, Inc.
800-736-4648
Rayovac Canada
800-268-0425

MADE IN CHINA

11

10

Battery Disposal

Battery Removal

When your rechargeable shaver reaches
the end of its useful life, the batteries must
be removed from the shaver and be recy­cled or disposed of properly in accordance
with your local and state requirements.

The following procedures should be
followed for battery removal:

■ Make sure your shaver is unplugged
from any outlets, so you
don’t risk an electrical
shock.

■ Remove the Head

Assembly by gently lifting
the assembly away from
the shaver.

■ Using a small Phillips

head screwdriver, remove

the screws from the
upper and lower back of
the shaver.

■ Pull or gently pry the
shaver halves apart,
exposing the battery.

■ Hold each battery in place
and very carefully slide
the clips from the termi­nals on each battery.

■ Lift or pry the battery out of the shaver.

CAUTION: DO NOT PUT IN FIRE OR MUTI­LATE YOUR BATTERIES WHEN DISPOSING
AS THEY MAY BURST OR RELEASE TOXIC
MATERIALS. DO NOT SHORT CIRCUIT AS IT
MAY CAUSE BURNS. DISPOSE PROPERLY IN
ACCORDANCE WITH YOUR LOCAL AND
STATE REQUIREMENTS.

The EPA-certified RBRC

®

Battery Recycling Seal on
the nickel-cadmium
(Ni-Cd) battery indicates
Rayovac Corporation is vol­untarily participating in an industry program
to collect and recycle these batteries at the
end of their useful life, when taken out of
service in the United States or Canada. The
RBRC

®

program provides a convenient
alternative to placing used Ni-Cd batteries
into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 800-8-BATTERY

SM

for informa­tion on Ni-Cd battery recycling and disposal
bans/restriction in your area. Rayovac
Corporation’s involvement in this program is
part of our commitment to preserving our
environment and conserving our natural
resources.

Performance Guarantee

Full Two-Year Warranty

Spectum Brands, Inc. warrants this product
against any defects that are due to faulty
material or workmanship for a two-year
period from the original date of consumer
purchase. This warranty does not include
damage to the product resulting from
accident or misuse.
If the product should become defective
within the warranty period, we will repair it
or elect to replace it free of charge. Return
your product and sales receipt with your
name, address and day time phone number
to: Spectum Brands, Inc. ,Attention:
Consumer Services, 601 Rayovac Drive,
Madison, WI 53711. For more information
call 800-736-4648.

Warranty excludes:

■ Screens and cutters

KEEP ORIGINAL SALES RECEIPT AS
PROOF OF PURCHASE FOR WARRANTY
PURPOSES.

This warranty does not cover products
damaged by the following:

■ Accident, misuse, abuse or alteration

of the product

■ Servicing by unauthorized persons

■ Use with unauthorized accessories

■ Connecting it to incorrect current

and voltage

■ Wrapping cord around appliance

causing premature wear & breakage

■ Any other conditions beyond our control

SPECTUM BRANDS, INC. SHALL NOT BE
RESPONSIBLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS
PRODUCT.ALL IMPLIED WARRANTIES
INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF FITNESS AND

T22-17222

®

CS27830_R-845_series_IB 6/20/05 3:41 PM Page 10

®

®

MC

CS27830_R-845_series_IB 6/20/05 3:41 PM Page 36