READ ALL WARNINGS AND
INSTRUCTIONS IN THIS
MANUAL BEFORE USING THIS SHOT
AGE 2 ........THE TEN COMMANDMENTS OF FIREARM SAFETY
P
PAGE 7 ........IMPORTANT PARTS OF THE FIREARM
PAGE 10........ASSEMBLY INSTRUCTIONS
........LOADING AND UNLOADING
AGE 13
P
GUN
AGE 15
P
PAGE 18
FIRING
......
DISASSEMBLY INSTRUCTIONS
......
1
Safety is Critical to Performance.
A superbly crafted gun is only as good as the hands that hold it. You can never be too careful. Shooting
accidents are often caused by careless oversights such as failing to control the direction of the muzzle, failing to
fully engage the safety, leaving ammunition in the chamber or using improper loads. These oversights can result
in the destruction of life, limb or property. There’s no calling back a bullet once it’s been fired, so it’s
critical that you know the principles of safe gun handling and storage before you ever take your new Remington
firearm out of the box.
The proper use and performance of your firearm depends on correct assembly and maintenance, so it’s critical
that you familiarize yourself with the information in this instruction book. Even if you’re a veteran shooter with a
collection of Remington firearms, take the time to read this literature. Not all firearms are the same. That means
the first step in safe handling is to learn the features and requirements of your new Remington.
THE TEN COMMANDMENTS OF FIREARM SAFETY
With the privilege of owning a firearm comes the responsibility to use it safely. You must understand and follow
the Ten Commandments of Firearms Safety at all times. These time-honored safety rules apply to your ownership
and handling of any firearm. They must govern your actions whenever and wherever you are involved with
firearms . . . in the field, on the range, or in your home. Commit these Ten Commandments to your memory.
1st COMMANDMENT
Always Keep the Muzzle Pointed in a Safe Direction.
This is the most important gun safety rule. A safe direction is one in which an accidental discharge will not cause
injury to yourself or others. Never allow your gun to point at anything you don’t intend to shoot. Be especially
careful when you’re loading or unloading. Treat every gun as if it were loaded. And make it a habit to know where
the muzzle is pointed at all times, even when your firearm is unloaded. No one will be injured by an
accidental discharge if you keep your firearm pointed in a safe direction. It’s as simple as that.
2nd COMMANDMENT
Firearms Should be Unloaded When Not in Use and Secured from
Unauthorized Use.
Load your firearm only when you are in the field or on the range and ready to shoot. Unload your firearm as
soon as you are finished shooting. Never bring a loaded firearm into your camp, home or vehicle. Unloading
means unloading both
else, visually check the chamber, receiver, and magazine to make sure there is no ammunition anywhere in the
firearm. Never assume a firearm is unloaded, and never take someone’s word for it - look for yourself. When
you are finished shooting and have completely unloaded the firearm, leave its action open.
Whenever you are carrying a loaded firearm in the field, you must unload it before crossing a fence, climbing
into a tree stand or blind or in any other situation where you may not be able to fully control the firearm. Never
pull or push a loaded firearm toward yourself or another person.
Store your firearms unloaded in a secure place where unauthorized persons cannot gain access to them. Store
ms and ammunition separately
ear
fir
you must still keep the firearm unloaded when locked. Whether you utilize a locked gun safe or external locking device, it is your responsibility to make sure that children and other unauthorized persons cannot gain access
m and ammunition.
to your fir
ear
the chamber and the magazine. Before handling a firearm or passing it on to someone
. If you use an exter
nal security device such as a cable lock or trigger lock,
232
3rd COMMANDMENT
Never Rely on Your Firearm’s Safety Mechanism to Justify Careless Handling.
If your firearm is equipped with a manual safety mechanism, do not rely on the safety as an excuse for improper or careless handling of the firearm. The safety mechanism is merely a supplement to your proper handling of
the firearm. The safety mechanism may be broken or altered. Even if you think you have previously engaged
the safety in the “safe” position, it may have been inadvertently disengaged without your knowledge while being
carried. Never assume that the safety mechanism is engaged in the “safe” position. Your assumption may be
wrong or mistaken. Treat your firearms safety mechanism like you would treat any other mechanical device - as
something that could break or fail.
Not all safety mechanisms operate in the same manner. Before using any firearm, know and understand precisely how the safety mechanism on that particular firearm operates. Never pull the trigger when the safety
mechanism is in the “safe” position, and keep your fingers away from the trigger while loading, unloading, and
engaging or disengaging the safety mechanism.
4th COMMANDMENT
Know Your Target and What’s Beyond It.
Never fire a shot unless you know exactly where the shot is going and what it will strike. Bullets and shot can
travel great distances with deadly velocity. When hunting game, never fire at a sound, a movement or a patch of
color - an impulsive shot can have tragic consequences. A fellow hunter in camouflage may be mistaken for
game by an impulsive shooter.
In addition to being sure of your target, you must know what lies beyond the target. In other words, make sure
of your backstop. Also, beware of ricochets - never shoot at water or a hard surface.
5th COMMANDMENT
Use Proper Ammunition.
Every firearm is designed to use only a specified caliber, gauge or length of ammunition. Use of the wrong
ammunition can cause serious personal injury or death. It is your responsibility to make sure the ammunition
exactly matches the specifications for your firearm.
Use of improperly reloaded ammunition can also be dangerous. Firearms are designed, manufactured, and
proof-tested to specified industry standards. Hand-loaded or reloaded ammunition that deviates, either intentionally or accidentally, from specified loadings can be extremely hazardous. It is strongly recommended, therefore, that you use only factory ammunition from a reputable ammunition manufacturer. If you do reload, you
have assumed the risks and responsibilities of an ammunition manufacturer.
6th COMMANDMENT
If Your Firearm Fails to Fire When You Pull the Trigger, Handle With Care.
If a chambered round of ammunition does not fire when you pull the trigger, stop and keep the muzzle pointed
in a safe direction. Treat your firearm as if it could still discharge. Keep your face away from the breech. Slowly
and carefully open the action, return the safety mechanism to the “safe” position, and unload the cartridge from
the chamber. Dispose of the cartridge safely. If your firearm repeatedly fails to fire when you pull the trigger, take
your firearm and ammunition to a competent gunsmith or return the firearm to the manufacturer for inspection.
3
3
7th COMMANDMENT
Always Wear Eye and Ear Protection.
Wear protective shooting glasses and hearing protection when shooting. Be sure to wear eye protection when
disassembling or cleaning a firearm to protect your eyes from springs and other tensioned parts. Continued
exposure to shooting noise can permanently damage your hearing.
8th COMMANDMENT
Be Sure the Barrel is Clear of Obstructions Before Shooting.
With your firearm completely unloaded, open the action and make sure there are no obstructions or debris in the
barrel. Even a small obstruction such as snow or mud in the barrel can cause the barrel or receiver to burst when
the next round is fired. Use a cleaning rod to remove obstructions and residues from the barrel. If the firing
noise or recoil seems weak, stop and completely unload your firearm to check for obstructions before firing
another shot. NEVER try to shoot out an obstruction by loading and firing another round of ammunition.
9th COMMANDMENT
Never Alter or Modify Your Firearm and Have it Cleaned and Serviced Regularly.
Your firearm has been carefully designed and manufactured to operate according to certain factory specifications.
NEVER alter or modify your firearm, especially its trigger or safety mechanism, in any way. Such alterations or
modifications can adversely affect the safe operation of your firearm, endangering you and those around you.
As with any mechanical device, the parts of a firearm are subject to wear or breakage. To assure optimum safety and performance, your firearm must be maintained and serviced on a regular basis. Only a competent gunsmith or a Remington Authorized Service Center should service or repair your firearm.
Proper cleaning and lubrication are also important to maintain the safe and proper functioning of your firearm.
Follow the cleaning and lubrication instructions set forth in the owner’s manual for your firearm. NEVER attempt
to clean or lubricate a loaded firearm.
10th COMMANDMENT
Learn How Your Firearm Operates.
Not all firearms are alike. Before you use any firearm for the first time, you must become totally familiar with
how that firearm operates. When you receive a new firearm, read and understand the owner’s manual before
assembling the firearm for the first time. If you acquire a used firearm, request an owner’s manual and have the
rifle inspected by a competent gunsmith to determine whether it is in good working order. If you do not have an
owner’s manual, contact the manufacturer to obtain one. If you are selling or trading your firearm to someone
else, be sure to transfer the owner’s manual to the new owner.
LEAD EXPOSURE WARNING
Discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition may result in exposure to lead, a substance known to cause birth defects, reproductive harm, cancer and other serious physical
injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure.
SHOOT SOBER!
Guns and alcohol or drugs don’t mix. Never consume anything that would even mildly impair your judgement or
physical coordination while handling a firearm.
WARNING
e to follow any of these safety r
Failur
damage to property. Do not use a firearm until you fully understand and practice the Ten Commandments of
Firearm Safety. If you have any questions about the safe use of a Remington firearm, write to us at Remington
ms Company
Ar
, Inc., Consumer Ser
ules may cause personal injur
vice, P.O. Box 700, Madison, NC 27025-0700, or call us at 1-800-243-9700.
4
y or death to the shooter or bystander and
Use the Security Lock Provided with your Shotgun
This shotgun comes with a security lock to assist in protecting against unauthorized use. (See Picture 1).
The shotgun must be completely unloaded when the security lock is in place.
cannot substitute for securing your firearm and ammunition in separate, locked locations.
Picture 1
The security lock operates as follows:
1. 1. To open the Trigger Lock put the Key into the notches of the Trigger Lock Nut and unscrew it counterclockwise. (See
Picture 2). Remove the Trigger Lock Screw.
WARNING: Using the security lock
Picture 2
2. 2. To install the Trigger Lock, put the Trigger Lock over the trigger guard with the smaller end of
the Trigger Lock shroud pointing toward the muzzle. Then place the Trigger Lock Screw through the
cross-slotted hole on the side of the Trigger Lock Shroud. (See
Picture 3Picture 4
Pictures 3 and 4).
5
Use the Security Lock Provided with your Shotgun (cont’d)
3. To secure the Trigger Lock on the trigger guard insert the Trigger Lock Screw into cross hole of the Trigger
Lock choose the best position for preventing the Trigger Lock from moving (See
Picture 5
4. To remove the Trigger Lock, unscrew the Trigger Lock Nut with the key and detach the Trigger Lock Screw.
(See
Picture 6).
Picture 5).
Picture 6
WARNING
Always store the key to the security lock: (1) in a separate location away from the auto loading shotgun; (2) in a secure location unknown and
not accessible to others, especially children. Whether you secure your firearms by using the supplied security lock, a gun lock or safe or some
other mechanism, it is YOUR RESPONSIBILITY to store your firearms in such a manner that children and other unauthorized persons cannot
gain access to them.
Important Parts of the Firearm
Congratulations on your choice of a Remington®Model SPR 453 Auto Loading shotgun. With proper care and if
used in accordance with the Ten Commandments of Firearm’s Safety and this owner’s manual, your shotgun
should give you many years of dependable use and enjoyment. The following picture depicts the main parts of
your shotgun and will aid in understanding the instructions in this Owner’s Manual.
STOCK
SAFETY MECHANISM
This picture shows the main parts of a Remington Model SPR453 Auto Loading shotgun. The picture will aid in understanding the instructions in this book.
TRIGGER
RECEIVER
TRIGGER GUARD
BARREL
MUZZLE
External Control Parts
Trigger Block Safety: The trigger block safety of the Model SPR 453 shotgun provides protection against
accidental and unintentional discharge under normal usage when properly engaged and in good working order. The
safety mechanism is not a substitute for following the rules of safe gun handling. Do not disengage the safety unless
you are ready to fire.
OR USE THE SHOTGUN.
The safety mechanism is a cross-bolt-button-style safety located on the trigger housing behind the trigger. To place
the safety in the “on” or “safe” position, push the button all the way to the right. (See Picture 7). When in the “on”
or “safe” position, the safety blocks the rearward motion of the trigger. To place the safety in the “off” or “fire”
position, push the button all the way to the left. When in the “off” or “fire” position, a red ring is exposed on the
left side of the safety button. See Picture 8. You have now disengaged the safety and the shotgun is in the
ready-to-fire position.
SAFETY
MAKE SURE YOU UNDERSTAND HOW THE SAFETY WORKS BEFORE YOU LOAD
SAFETY
ON
Picture 7Picture 8
WARNING
Do not touch the trigger while moving the safety button. When operating the safety button, make sure you push it to the full extent of its travel in
the desired direction, either fully “on” or fully “off.” Half-safe or partially safe is UNSAFE.
OFF
7
External Control Parts (cont’d)
Carrier Latch/Bolt Release Button: The carrier latch/bolt release button is located on the right side of the shotgun and protrudes out of the forward right hand side of the receiver. (See
release the carrier latch as well as release the bolt if it is in the rearward position.
Picture 9
Carrier Latch: The carrier latch is located under the receiver in front of the trigger guard. (See Picture 10).
Depressing the carrier latch will release the lock on the latch so that it can be moved for loading the shotgun.
Picture 9). Pushing in on the button will
Picture 10
Trigger: The trigger is located in the trigger guard. (See Picture 11). If you pull the trigger with the safety in the
“OFF” or “FIRE” position, the shotgun will fire.
Picture 11
WARNING
eady to pull
Never pull the trigger until you ar
the trigger and fir
fingers are outside the trigger guard and away from the trigger.
e the shotgun. When opening and closing the action and when engaging or disengaging the safety mechanism, make sur
e actually r
e. Keep your fingers of
eady to fir
f the trigger and outside of the trigger guar
d until you ar
e r
e your
8
External Control Parts (cont’d)
Bolt Cocking Handle: The bolt cocking handle is located on
the right side of the shotgun and protrudes form the bolt and is
used for pulling the bolt rearward. (See
note that if the shotgun has been cocked and the bolt has been
eleased to the forward position, the bolt will not lock back in the
rearward position unless the carrier stop button has been moved
rearward.
Carrier Stop Button: The carrier stop button is located on the
right hand of the receiver at the forward end of the trigger housing.
Picture 13). The carrier stop button is a flat button that
(See
moves forward and rearward and resets the bolt catch and locks
the carrier latch in the down position. If the shotgun has been
cocked, the bolt will not lock back in the rearward position
unless this button has been pushed rearward.
The Forend Cap: The forend cap is located on the end of
the magazine tube at the front of the forend and under the barrel.
Picture 14). The forend cap screws onto the magazine
(See
tube using a right-hand thread.
Picture 12). Please
Picture 12
Picture 13
WARNING
The forend cap is under spring pressure. Use caution when screwing and unscrewing the forend cap from the end of the magazine tube.
Picture 14
The Serial Number: The shotgun’s serial number is located on the left bottom side of the receiver.
The Cocking Indicator: The cocking indicator is located in the front inside of the trigger guard. (See Picture
). When cocked the indicator is visible. When fired or uncocked, the indicator is not visible. (See Picture 16).
15
WARNING
The cocking indicator is merely an aid to help you confirm when hunting or shooting that your shotgun is cocked and ready-to-fire. NEVER rely
on the status of the cocking indicator to justify careless handling of your shotgun. The ####### indicator may be broken or obscured. Always
handle your shotgun as if it were loaded, cocked and ready-to-fire.
Picture 15Picture 16
9
Instructions For Assembly Of Shotgun
WARNING
efore you begin to assemble the shotgun, you MUST (1) look down the barrel from the beech end toward the muzzle end to make sure there is
B
o ammunition in the chamber or obstruction in the barrel (See Picture 17), and (2) make sure the safety is in the “ON” or “safe” position.
n
Picture 17
Your shotgun was shipped with the barrel detached from the receiver assembly. To assemble the shotgun, follow
these instructions:
1. When you open the box of your next Model SPR 453 shotgun, the barrel is separated from the stock and
receiver of the shotgun. To attach the barrel, first remove the stock and receiver from the plastic bag. Then
unscrew the forend cap. (See
Pictures 18 and 19).
Picture 18Picture 19
WARNING
The magazine cap is under spring pressure. Note: After assembly of the shotgun the spring in the magazine tube may become twisted. This will
cause a decrease in magazine tube capacity. If you load and unload the magazine tube the spring will untwist and the capacity should be as
defined in the manual.
2. If the plastic spring cap is not installed in the magazine tube, use a small pin in the hole in the end of the
magazine tube to hold the spring during removal of the cap. Unscrew the cap until you see the hole in the
tube. Then insert the pin through the hold and hold the spring. (See
Picture 20
Picture 20).
10
Instructions For Assembly Of Shotgun (cont’d)
3. Remove the forend from the magazine tube. (See Picture 21).
Picture 21
4. Remove the barrel from the box and remove the plastic bag from the barrel. Insert the barrel extension
into the receiver (between the bolt and the receiver) while making sure the barrel lug is aligned with the
magazine tube. Continue sliding the barrel extension into the receiver and allow the barrel lug to slide
over the magazine tube. With the barrel extension partially inserted into the receiver between the bolt and
the receiver, pull the bolt cocking handle to the rear so that the bolt is locked back. Now completely insert
the barrel extension into the receiver. (See
5. Slide the forend over the magazine tube. Do NOT force the forend. Make sure that the forend is completely
seated around the magazine tube, barrel, and the receiver. The forend MUST be flush with the receiver.
Picture 23).
(See
Picture 22).
Picture 22Picture 23
6. Screw on the forend cap so that the forend is held firmly in place and flush against the receiver.
(See Picture 24).
Picture 24
11
Instructions For Assembly Of Shotgun (cont’d)
7. With the forend and the barrel in place and the forend cap securely in place, depress the carrier latch
button and the bolt will slide into the barrel extension (Note: If you see any portion of the barrel extension
protruding from the receiver after you released the bolt or if there is a gap between the forend and the
receiver you have not properly assembled the shotgun). If the bolt does not slide forward or you have gaps
or the barrel extension protrudes from the receiver, reverse the assembly procedures and start over again
making sure that the barrel is fully inserted into the receiver and that the forend is fully in place. If you still
cannot assemble the shotgun correctly, take the shotgun to the dealer where you bought the shotgun or
to a qualified gunsmith for assistance.
8. Once the shotgun is assembled (or if you cannot fully assemble the shotgun and plan to carry it
somewhere for assistance) engage the trigger block safety and keep it engaged in the “ON’ or “safe”
position until you are ready to fire the shotgun. Keep the safety “on” no matter if the gun is loaded
or unloaded.
Note!
Locking Block Placement:
tured. See Picture 25. Make sure that the firing pin spring and the firing pin washer are held rearward by the
locking lug. (See
Picture 26
During assembly or reassembly make sure the locking lug is in placed as pic-
Picture 25Picture 26
WARNING:
Never load or fire the shotgun unless the barrel is properly attached to the receiver, and the forend is properly locked into the receiver.
WARNING
Make sure the shotgun is pointed in a safe direction and the trigger block safety is engaged at all times while loading and unloading. NEVER
allow fingers or other objects to contact the trigger while loading or unloading.
WARNING
Do not disengage the trigger block safety until you are ready to fire and have the shotgun pointed safely downrange
ARNING
W
: Do not load the shotgun until you ar
eady to fir
e r
e.
12
Loading and Unloading Your Shotgun
TO LOAD:
1. Make sure the ammunition that you are using is the correct size and gauge. The barrel is marked with the
gauge and chamber size. A barrel marked 3
(89mm) shotshells of the correct gauge as marked on the barrel.
2. Visually inspect the chamber and barrel for obstructions by pulling back the bolt until it locks back. Note
that if the bolt will not lock back then push the Carrier Stop Button (see
locking the bolt rearward. The chamber and barrel should be free of oil or grease or obstructions.
Picture 27).
(See
Picture 13Picture 27
1
/2” (89mm) will use 2 3/4” (70mm), 3” (76mm) or 3 1/2”
Picture 13) rearward and retry
3. After inspection, release the bolt by depressing the carrier latch button (See
e 9
Pictur
Picture 9).
4. Turn the shotgun upside down so that the barrel is pointing toward the ground and you are looking at the
3
carrier latch. Now depress the carrier latch and insert up to five (5) – 2
1
cartridges or (4) – 3
/2” cartridges into the magazine tube. Note that if the plastic spring cap is in the
magazine tube, then the magazine capacity is decreased by one round. (See
/4” cartridges or five (5) – 3”
Picture 28).
13
Picture 28
Loading and Unloading Your Shotgun (cont’d)
TO UNLOAD:
1. Make sure the trigger block safety is engaged and your fingers are away from the trigger. Keep the
muzzle pointed in a safe direction. Draw back the bolt until a cartridge is ejected or the bolt has traveled
to the rear fully. (See
the bolt back forward until it is fully closed. Repeat the drawing back of the bolt while depressing the
carrier stop button until no more rounds are ejected from the shotgun.
2. When you have ejected the last round from the shotgun, pull the bolt fully to the rear. The bolt should lock
in the rearward position. With the bolt locked back, visually inspect the chamber to insure that it is empty.
You should also look down into the receiver through the ejection port and verify that the magazine tube
is empty. (See
Picture 29). If there was no cartridge in the chamber, nothing will be ejected. Slide
e 29
Pictur
Picture 30).
Picture 30
If for some reason a cartridge in the magazine tube will not rise up into the chamber to be ejected, after repeated
attempts to manually cycle the shotgun, perform the following steps:
A) Manually close the bolt by depressing the bolt release button.
B) Turn over the shotgun so that the trigger guard is facing
you (upward). Depress the carrier latch button and then
depress the carrier latch. (See
Picture 31).
C) With the same finger that you are depressing the carrier
latch, depress the Shell Latch. The Shell Latch is located
on your left hand side with the shotgun in the upside down
position. It is the piece of metal that should be holding the
e 31
round in the magazine tube. The cartridge should slide up
Pictur
and out of the magazine with your guidance. Note: the cartridge
is under spring tension. Repeat this process until the magazine tube is empty. Turn the shotgun over
and lock the bolt back and verify that the gun is empty. If you had to follow the procedure for a cartridge
that was not being released from the magazine tube, make sure the shotgun is empty and let a qualified
gunsmith inspect the shotgun before you load or use the shotgun again
Firing Your Shotgun
WARNING: Never load or fire the shotgun unless the barrel is properly attached to the receiver, and the forend is
properly locked into the receiver.
WARNING
o not disengage the trigger block safety until the shotgun is pointed in a safe direction and you are ready to fire.
D
WARNING
f a cartridge does not fire and the trigger has been pulled and the trigger block safety is disengaged…Stop! and do the following: a) Make sure
I
he gun is pointed in a safe direction b) Engage the trigger block safety c) Wait 60 seconds d) Follow the instructions above for unloading the
t
hotgun.
s
WARNING
If during firing the sound of any cartridge is noticeably softer or louder than the previous cartridge fired…Stop! Do not load another cartridge
or fire another cartridge and do the following: a) Make sure the gun is pointed in a safe direction b) Engage the trigger block safety c) Follow the
instructions above for unloading the shotgun and d) With the shotgun unloaded, visually inspect the barrel for blockage or damage. Then inspect
the receiver of the shotgun for damage before continuing.
READ, UNDERSTAND AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE FIRING THE
SHOTGUN.
TO FIRE THE SHOTGUN:
1. 1) Make sure the shotgun is pointed in a safe direction wit the trigger block safety engaged.
(See
Picture 32).
2. Make sure you are wearing eye and ear protection.
3. Keeping your fingers away from the trigger, push the trigger block safety to the “off” or “fire” position with
the red ring showing. (See
Picture 33).
Picture 32Picture 33
ith the butt stock held fir
W
4.
mly against your shoulder and the bar
rel pointed towards your intended target,
place your trigger finger on the trigger. The shotgun will fire when you pull or squeeze the trigger with
the requisite force. See Picture 34. Auto loading shotguns automatically eject the fired cartridge from the
chamber and feed the next live round from the magazine tube into the chamber each time the
shotgun fires. No mechanical force is required for the shotgun to complete the ejection and
chambering operations.
15
Firing Your Shotgun (cont’d)
(See Picture 34). Auto loading shotguns automatically eject the fired cartridge from the chamber and feed
the next live round from the magazine tube into the chamber each time the
shotgun fires. No mechanical force is required for the shotgun to complete the ejection and
chambering operations.
Picture 34
WARNING
You must be aware that the firearm will be ready to fire another round immediately after the previous round has been ejected and the new round
has been chambered. IF you finish shooting before the last round in the shotgun is fired, you msut immediately put the safety in the “ON” or
“SAFE” position and control the direction of the muzzle. Remember that a live round is in the chamber.
WARNING
During firing, the bolt cocking handle travels rearward with considerable force and velocity. Do not allow any object to enter or obstruct its path.
5. Once you fire all the rounds from the shotgun, the bolt should lock open upon firing of the last cartridge.
Never rely on the locked back bolt as a signal that the gun is empty. ALWAYS visually check the chamber to insure that the gun is empty. It is also possible that the bolt will not lock back after the firing of the
last cartridge. If this occurs, open the bolt manually and lock it to the rear. Note: If the bolt will still not
lock back then push the Carrier Stop Button rearward and retry locking the bolt rearward. Use you eyes
to verify that the gun is completely empty.
WARNING
Once you have stopped firing the auto loading shotgun, immediately push the cross trigger block safety back to the “on” or “safe” position. Then
follow the unloading instructions above while keeping the muzzle pointed in a safe direction.
GAS SYSTEM ADJUSTMENT: The Model SPR 453 shotgun has a unique self-regulating gas system. It is
preset at the factory to function reliably with a wide range of 12 gauge ammunition ranging from 12 Ga./2
1
/4oz.) shells to 12 Ga./3.1/2” shells. This system also allows you to fine tune the function of the shotgun
(1
3
/4”
with the gas system nut. By adjusting the gas system nut, you can make your shotgun function over the
complete range of 12 Ga. ammunition and set the shotgun for optimum function for the user. The gas system
ements without additional parts or kits
nut allows you to customize the function of the shotgun to your r
equir
GAS CYLINDER NUT: The gas cylinder nut is located under the barrel on the front end of the gas cylinder.
Picture 35). The gas cylinder nut retains the valve spring with the valve, which provide the action of the
(See
shotgun with light loads as well as with heavy loads.
16
Firing Your Shotgun (cont’d)
Picture 35
Note: For the first 100 rounds. use 1 1/4oz. loads or greater for break-in. Your shotgun was set at the factory to
1
use 12 Ga./3
shot 12 Ga./3
to use loads lower than 12 Ga./2
/2” steel shot to 12 Ga./ 2 3/4” (1 1/4 oz.). After break-in, if you wish to use lead or tungsten based
1
/2” rounds, then you must adjust the gas cylinder nut two turns counter-clockwise. If you wqish
3
/4” (1 1/4oz.) you must adjust the gas cylinder nut as required by turning it
clockwise.
Never adjust the gas cylinder nut more than two complete turns in any direction. For reference use the notch on
front of the gas cylinder. The nut should be visible through the notch and at the most should fit flush the front
end of the gas cylinder. To set the shotgun back to factory setting, see the mark on the gas cylinder and adjust as
required. (See
Picture 35).
Note: Screw the gas cylinder nut but do not detach the barrel from the receiver. (See Picture 36).
Picture 36
MAGAZINE PLUG PLACEMENT: The wooden or plastic rod enclosed with your shotgun is a magazine plug
and can be placed inside the magazine tube spring from the cap end. The rod prevents the magazine follower
from moving the full length of travel.
It is present for one round in the magazine without the plastic spring cap. You will see a mark on the rod which
is where you would cut the rod if you want two rounds in the magazine without the plastic spring cap. If you
want to use the plastic spring cap and the magazine plug you will have to cut the rod at the mark.
17
Instructions For Disassembly Of The Auto Loading Shotgun
1. Make sure the combination rifle/shotgun is unloaded (FOLLOW UNLOADING INSTRUCTIONS)
and pointed in a safe direction.
2. Make sure the cross trigger block safety is engaged in the “ON” or “SAFE” position. (Red band will not
show). (See
3. With the bolt in the forward position, unscrew the forend
cap and remove the forend. Push the Carrier Stop Button
rearward and move the to the rear slightly and hold it out
of battery. Then grasp the barrel and remove the barrel by
pulling the barrel and barrel extension out of the receiver.
(See
Picture 37).
Picture 38).
Pictur
e 37
Picture 38
4. Use the back end of an empty cartridge or a flathead
screwdriver or yor fingers to remove the Bolt Cocking
Handle. Insert the screwdriver or back of empty cartridge
into the notch and pry up handle and remove from the
bolt or grasp the handle firmly and pull out and away
from the receiver. (See
Picture 39).
5. With the cocking handle removed from the bolt you now
can grasp the gas piston and slide the bolt and action bar
forward and remove the assembly from the magazine tube
and receiver. Be careful because once the bolt is removed
from the receiver all the pieces from the assembly are free
to seperate. We suggest you keep the gun with the bolt up
when you remove the assembly does not seperate. See
locking block placement section. (See
Picture 40).
6. The trigger assembly can be removed with the barrel and
bolt removed or without the barrel and bolt removed. To
remove the trigger assembly, remove the two pins that hold
the trigger assembly in place and pull the trigger assembly
from the receiver. The pins can be removed with a hammer
and a punch. (See
Picture 41).
18
Picture 39
Picture 40
Picture 41
Manufacturer’s Warning
This firearm was manufactured to properly perform with the original parts as designed. It is your duty to make
sure any parts you buy are correctly installed and that neither replacements nor originals are altered or changed.
Your shotgun has many parts that must relate correctly to other parts for safe and accurate operation. Putting a
gun together wrong or with modified parts can result in a damaged gun, or personal injury or death to you or
others. Always let a qualified gunsmith work on your gun or at least, check any work not performed
by a gunsmith. Firearms safety is your primary concern.
RESPONSIBILITY FOR THE CORRECT REASSEMBLY AND FUNCTIONING OF THE FIREARM AFTER
ANY DISASSEMBLY OR REPLACEMENT OF PARTS.
THE GUN OWNER MUST ACCEPT FULL
To Clean and Maintain Your Shotgun
A. Follow procedures for unloading shotgun as described previously.
B. Follow procedures for disassembly of shotgun as described previously.
C. Materials needed to clean this shotgun are: a cleaning rod, cotton bore patches, brass bore brush,
powder solvent (such as Remington BriteBore
(such as Rem
WARNING
Lead or lead compounds are known to the State of California to cause cancer, birth defects, reproductive toxicity, and other serious physical
injury. Those who clean firearms should take protective measures to avoid contact or exposure to such chemicals.
®
Oil).
™), a small soft brush and good quality gun oil
D. Using the bore brush with powder solvent, scrub the interior of the barrel and chamber to remove any
powder and lead residue in the bore. Always and lastly, swab the interior of the barrel with a cotton patch
with gun oil to coat and protect the bore and chambers from rust and corrosion.
E. Any powder fouling on the firing wall, barrel, etc. can be easily cleaned with a brush and powder solvent.
F. All external surfaces should be wiped down with a light coat of rust preventative. Avoid using too much
oil as powder, dust or other foreign material may get trapped in the oil. This could lead to congealed
deposits which may interfere with the safe and reliable operation of this shotgun.
USE CAUTION while using solvents in gun bore cleaning. Prolonged or excess contact with
G.
solvents can damage the gun’s bluing and finish. Be sure to wipe away all excess solvent and then
lubricate with oil.
ts should be wiped with an oiled cloth
A gun should be cleaned after firing. In addition, exter
H.
after handling. A light oil is or
very little. If a gun is used frequently, it must be cleaned after each firing and regularly serviced by a
professional gunsmith. If the gun has been stored, remove all excess oil and/or grease before firing.
Always check to be sure that no cleaning patch or other obstruction remains in the bore or chambers
before firing.
dinarily all that is necessary in cleaning if the gun has not been fired or fired
nal par
19
To Clean and Maintain Your Shotgun (cont’d)
GAS PORTS: The two holes in the barrel gas porting ring are the gas ports which regulate the auto-loading
function of the shotgun. (See
properly. Make sure these holes are cleaned after each use. Also clean the barrel gas porting ring.
GAS PISTON ASSEMBLY: The gas piston assembly is on the magazine tube. (See Picture 43). The gas
piston assembly must be cleaned and lightly oiled after each use.
Picture 42). These holes must remain open and clear for the shotgun to function
Pictur
e 42
Pictur
e 43
DANGER – Ammunition Warning
Firearms may be damaged and serious personal injury or death to the shooter or bystanders may result from any
condition which contributes to the generation of excessive pressure or uncontrolled release of gas within the
firearm. Such adverse conditions can be caused by bore or chamber obstructions, propellant powder overloads or
by defective, incorrect or improperly loaded and assembled cartridge components. Even the strongest firearm can
be blown up as a result of excessive pressure. It is extremely dangerous to use a cartridge whose pressure is
greater than that developed by cartridges loaded to industry standards.
Ammunition (Cartridges) Notice
We specifically disclaim responsibility for any damage, injury or death occurring in connection with or as the
result of the use of the shotgun with faulty, non-standard, remanufactured, hand loaded or reloaded ammunition
or with cartridges other than factory cartridges for which the shotgun was originally chambered.
Lubrication Warning
Firing a shotgun with oil, grease or any other material even partially obstructing the bore may result in damage to
the shotgun and personal injur
ammunition. If the powder charge of a cartridge is affected by the lubricant, they may not fully ignite yet the energy from the primer and/or powder may still be sufficient to push the projectile or wad into the bore where it may
become lodged. Firing a subsequent cartridge into the obstructed bore will damage the shotgun and may cause
personal injury to the shooter and those nearby. Use lubricants properly. You are responsible for the proper care
and maintenance of your firearm and ammunition.
y to the shooter and those nearby
. Do not spray or apply lubricants dir
ectly on
20
PARTS AND SERVICE
To Order Parts
ALL PARTS ARE SUBJECT TO A $10.00 CHARGE FOR SHIPPING AND HANDLING. Some parts are restricted and
may only be installed by returning the shotgun to us. When ordering parts, please state the Model, Gauge, Serial
Number, and Finish Color. For parts information, call (321) 639-1432.
Service
To obtain information about returning your shotgun for service or repairs, call (321) 639-1432.
One Year Limited Warranty
This shotgun is warranted to the original retail customer for one year from the date of retail purchase against
defects in material and workmanship. All parts and labor or replacement at our option are covered. The wood stock
is not covered by the one year warranty. The warranty on the wood stock is 60 days and is limited to the original
retail customer and extends 60 days from the date of retail purchase and covers only manufactured and material
defects. Transportation to and from our repair facilities, government fees, damage caused by failure to perform
normal maintenance, sales outside the United States, damage caused by use of high velocity, high pressure,
reloaded or other nonstandard ammunition, or by any unauthorized repair, modification, misuse, abuse or alteration of the shotgun is not covered by this Limited Warranty.
Implied Warranty
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL
RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law, which cannot be preempted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state.
To obtain warranty service, send your shotgun with proof of retail purchase, freight prepaid to:
REMINGTON I.S.P.
c/o USSG
402 Richard Road
Rockledge, FL 32955
NOTICE: It is illegal to ship a firearm with ammunition in the firearm or in the same packaging. Firearms and
ammunition must be shipped separately. For information about shipping ammunition, call (321) 639-1432.
Your Owner’s Manual
Always keep this manual with your firearm. Make sure you understand all the warnings, operation instructions and
safety procedures. When you lend, give or sell the firearm, be sure this manual goes with it. You can get a copy
of this manual fr
om Remington upon r
equest.
21
PARTS LIST
Model SPR453 Auto Loading Shotgun Exploded View
1.choke tube30.bolt58.carrier latch dog
2.barrel31.left extractor59.carrier latch dog pivot
ever install or remove choke tubes while the firearm is loaded. Only install or remove choke tubes with the firearm unloaded, the action open
N
nd the trigger block safely engaged.
a
Screw in Chokes Symbols/Markings
(This is an option – not all Model 100 shotguns have this feature)
The end of the choke tubes are marked with slashes to identify the choke construction:
/- Full
//- Improved Modified
/// - Modified
//// - Improved Cylinder
CI - Cylinder
WARNING
MAKE SURE YOU FULLY TIGHTEN THE CHOKE TUBE.
Shooting with a loose choke tube can cause damage to your shotgun.
Additional Information On Screw Choke Tubes:
A. Only tighten or loosen choke tubes with flat key wrench supplied with shotgun. Note: wrench (and extra
choke tube or tubes if supplied) are under the cardboard in front of the shotgun receiver in the box.
B. Never shoot the shotgun with a partially installed choke tube.
C. Model SPR 453 auto loading shotguns are available with fixed choke or screw choke barrels. There are
two types of screw chokes available: lead shot choke tubes and steel shot choke tubes. When installed,
steel shot choke tubes protrude approximately
3
/4” from the muzzle end of the barrel and the mating lip
will be flush with the end of the barrel. When installed, lead shot choke tubes fit flush with or slightly
below the muzzle end of the barrel. If you have lead shot choke tubes and intend to shoot steel shot
cartridges or slugs, then you must use only the IC or Cylinder tubes. DO NOT fire steel shot or slugs in
Modified, Improved Modified or Full lead shot choke tubes. If you have steel shot choke tubes, you may
fire steel shot cartridges through any of those choke tubes. DO NOT fire slugs in Modified, Improved
Modified or Full lead shot choke tubes or steel shot choke tubes.
D. Correctly installed choke tubes: Lead shot choke tubes should fit flush or slightly below the muzzle end
of the barrel. Steel shot choke tubes will protrude out from the barrel about
3
/4” and the mating lip will be
flush with barrel end.
E. Before using the shotgun make sure that the choke tubes are installed correctly.
F. Keep choke tubes lubricated and installed. Never fire the gun without a choke tube installed. Handle choke
tubes carefully since the leading edge is very thin.
23
Additional Information On Screw Choke Tubes: (cont’d)
Notes on Shot Material and Chokes:
1. Shells using Bismuth® or Tungsten-Matrix® shot are subject to the same barrel and choke tube limitations
as lead shot. Shells using Tungsten-Iron shot or Hevi-Shot® are subject to the same barrel and choke tube
limitations as steel shot.
2. On fixed choke guns, shells loaded with steel, Tungsten-Iron or Hevi-Shot® should be fired only in
IC or Cylinder barrels. DO NOT fire steel, Tungsten-Iron or Hevi-Shot® shells in fixed barrels with
Modified, Improved Modified or Full choke barrels. Lead, Bismuth® and Tungsten-Matrix® may be fired
in all fixed choke barrels.
3. On fixed choke guns, slugs may be fired in only IC and Cylinder barrels. DO NOT fire slugs in fixed choke
barrels with Modified, Improved Modified or Full chokes.
If you would like to buy extra choke tubes (skeet, trap, extra full, etc.) call (321)-639-1432.
WARNING
Children are attracted to and can operate
firearms that can cause severe injuries or
death. Prevent child access by always keeping guns locked
away and unloaded when not in use. If you keep a loaded
firearm where a child obtains and improperly uses it, you
may be fined or sent to prison.
ADVERTENCIA
A los ninos los atroen las armaside de fuego y
los pueden hacer funcionar. Ellos pueden
causarses lesiones graves y la muerte. Evite que los ninos
tengon acceso a los armas de fuego guardandolas siempre
con llave y descargadas cuando no las este utilizando. Si
usted tiene un arma de fuego cargado en un lugar en que
un nono tiene acceso a ella y la usa indebidamente.
Le pueden dar una multa a enviarlo a la carcel.
REMINGTON I.S.P.
c/o USSG
402 Richard Road
Rockledge, FL 32955
Manufacturer:
Izhevsky Mekhanichesky Zavod
omyshlennaya str.,
8, Pr
426063 Izhevsk, Russia
25
Remington is a trademark registered in the United States Patent and Trademark Office by Remington Arms Company, Inc.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.