Page 1
Owner’s
Owner’s
Manual
Manual
Instruction Book for:
Instruction Book for:
Models SP-10 magnum
Models SP-10 magnum
Autoloading Shotguns
Autoloading Shotguns
IMPORTANT!
READ ALL INSTRUCTIONS
AND WARNINGS IN THIS
BOOK BEFORE USING THE FIREARM.
page 2 ........the ten commandments of
page 7 ........important parts of the firearm
page 10 ......how to load and unload
page 12 ......lubrication and maintenance
page 16
firearm safety
......how to obtain parts and service
Page 2
A Tradition of Performance and Safety.
In 1816 Eliphalet Remington was confident he could make a flintlock that was as good or
better than any he could buy. His confidence was well founded. The barrel he handcrafted
set a new standard for firearm accuracy and spawned generations of products that have
made Remington
certainly hallmarks of Remingtonfirearms, one factor ultimately drives their performance.
Safety. Eliphalet Remington never lost sight of the fact that his rifles were potentially lethal
and could kill someone if handled improperly. And after more than 180 years the same
holds true for any firearm, including your new Remington. Eliphalet Remington’s first
flintlock launched a proud tradition of accuracy and responsibility.
Safety is Critical to Performance.
A superbly crafted gun is only as good as the hands that hold it. You can never be too careful. Shooting
accidents are often caused by careless oversights such as failing to control the direction of the muzzle, failing
to fully engage the safety, leaving ammunition in the chamber or using improper loads. These oversights can
result in the destruction of life, limb or property. There’s no calling back a bullet once it’s been fired, so it’s
critical that you know the principles of safe gun handling and storage before you ever take your new Remington
firearm out of the box.
The proper use and performance of your firearm depends on correct assembly and maintenance, so it’s critical
that you familiarize yourself with the information in this instruction book. Even if you’re a veteran shooter with
a collection of Remington firearms, take the time to read this literature. Not all firearms are the same. That means
the first step in safe handling is to learn the features and requirements of your new Remington.
The Ten Commandments of Firearm Safety should be etched in your memory forever. Let them govern your
action wherever and whenever you’re involved with firearms. In the field. On the range. Or in your home. Please
take the time to review and understand these rules.
®
Arms America’s leading gunmaker. While performance and style are
THE TEN COMMANDMENTS OF FIREARM SAFETY
Eliphalet Remington’s first
flintlock launched a proud tradition
of accuracy & responsibility.
1st COMMANDMENT
Always Keep the Muzzle Pointed in a Safe Direction.
This is the most important gun safety rule. A safe direction is one in which an accidental
discharge will not cause injury to yourself or others. Never allow your gun to point at
anything you don’t intend to shoot. Be especially careful when you’re loading or unloading. Treat every gun as if it were loaded. And make it a habit to know where the muzzle is
pointed at all times, even when your firearm is unloaded. No one will be injured by an
accidental discharge if you keep your firearm pointed in a safe direction. It’s as simple as
that.
2nd COMMANDMENT
Firearms Should be Unloaded When Not Actually in Use.
Load your firearm only when you’re in the field or on the target range and ready to fire. Never let a loaded gun
out of your sight or out of your hands. Unload it as soon as you’re finished shooting – before you bring it into
your car, camp or home. Remember, unloading your firearm means unloading it completely, so there is no
ammunition in the chamber or in the magazine. Before handling a firearm or passing it to someone else, visually check the chamber, receiver and magazine to be certain they do not contain ammunition. Always keep the
gun’s action open when not in use. Never assume a gun is unloaded even if you were the last person to use it.
Always check for yourself.
2
Page 3
Let common sense rule when you carry a loaded gun. If you’re in a situation that could risk accidental discharge – such as crossing a fence, wading through a stream or climbing a tree – always
unload your gun. Never pull or push a loaded firearm toward yourself or another person. And
never carry a loaded gun in a scabbard, detached holster or gun case.
Certain firearms (including some Remington®rifles and shotguns) are equipped with internal secu-
rity devices to prevent unauthorized use. In addition, some firearms owners use external devices,
such as cable locks and trigger blocks, for the same purpose. Even if you use such a device, you
should still keep your firearm unloaded when stored or not in use. And using internal or
external devices cannot substitute, however, for securing your firearms and ammunition in
a separate, locked location.
Safe storage of firearms is just as critical as safe handling. Never store guns loaded. Be
sure to keep your firearms in a secure place where unauthorized persons cannot get their hands on them without
your knowledge.
Take special care if there are children around. Children are fascinated by guns. It’s a natural curiosity that can have
tragic consequences when not properly supervised. Store your firearms in a locked gun safe or some other location that
physically bars a child from gaining access.
Ammunition should be stored and locked in a location separate from your firearm. Never leave an unsecured firearm
or ammunition in a closet, dresser drawer or under the bed. Remember, it is your responsibility to make sure that
children and others unfamiliar with firearms cannot get access to your firearm and ammunition.
3rd COMMANDMENT
Firearms should be stored in a
secure place where children cannot
access them. A gun safe is an ideal
way to secure your firearm.
Don’t Rely on Your Gun’s Safety.
Treat every gun as if it can fire at any time, whether or not there’s pressure on the trigger. Your firearm has been
carefully designed to maximize performance and safety. However, because a gun’s safety is a mechanical device, it
could fail.
Human error is a more likely reason for a gun safety to fail. By mistake, you may think the safety is on when it really isn’t. Or the safety may have been disengaged without your knowledge. Or you could think your gun is unloaded
when there’s actually a cartridge or shell in it. A mechanical safety is not a substitute for common sense. It’s merely a supplement to your proper handling of a firearm.
Never touch the trigger on a firearm until you are ready to shoot. Keep your fingers away from the trigger when
you’re loading or unloading. And don’t pull the trigger when the safety is engaged or positioned between safe and
fire.
Before using your gun, read this instruction book to understand the exact location and operation of your firearm’s
safety. Even when the safety is on, maintain control of your loaded firearm and control the direction of the
muzzle. In other words, don’t rely on your safety to justify careless handling. If your firearm’s internal
mechanisms are broken or have been altered, your firearm may fire even when the safety is on. Remember, you and
your safe gun handling practices are your gun’s best safety.
4th COMMANDMENT
Be Sure of Your Target and What’s Beyond It.
You can’t stop a shot in mid-air, so never fire unless you know exactly where your shot is going and what it will strike. Never fire at a
sound, a movement or a patch of color. A hunter in camouflage can
easily be mistaken for a target by an impulsive shooter. Before you
x
pull the trigger be absolutely sure of your target and what’
Make sure the shot has a
rial like sand. Remember, bullets can travel great distances with
tremendous velocity
target or the bullet ricochets.
backstop such as a hillside or dense mate-
. Know how far your shot will go if you miss your
3
s behind it.
Page 4
5th COMMANDMENT
Use Proper Ammunition.
Every firearm is designed to use a certain caliber or gauge of ammunition. Using the wrong ammunition, mixing
ammunition or using improperly reloaded ammunition can cause serious personal injury or death. And it only
takes one cartridge or shotshell of the incorrect caliber or gauge, or which has been improperly reloaded, to
destroy your firearm. It’s your responsibility to make sure the ammunition you use exactly matches the caliber or
gauge of your gun. Refer to this instruction book to find out the specific requirements of your firearm. Always
read and heed the instructions on ammunition boxes.
Confusing shells or cartridges can cause serious personal injury or death and destroy your firearm. Examine
your shells or cartridges closely and use only the precise caliber or gauge for your specific firearm. For
example, suppose you accidentally loaded a 20 ga. shell into a 12 ga. shotgun. Because the 20 ga. shell is too
small for the chamber, the 20 ga. shell could travel down the barrel and get lodged in the bore. If you then loaded
a standard 12 ga. shell behind it and fired, the 12 ga. shot will slam into the lodged 20 ga. shell and may cause
the barrel to explode right in your hand. This is commonly called a 12/20 burst, and it can kill you.
Check all ammunition before you load it to make sure it matches your gun’s requirements. Every Remington
cartridge and shell is head-stamped with its caliber or gauge for easy identification. Likewise, you’ll find the
caliber or gauge of your new Remington firearm imprinted on the barrel.
Reloading Requires Extra Diligence.
If you’re an ammunition reloader, you are responsible for personally assuring that the loads and components of
your reloaded ammunition meet your gun’s factory-tested standards. Never use ammunition which has been
reloaded by someone else!
Many shooters handload as a hobby or to save money on commercial, factory-made ammunition. However, it requires
a thorough knowledge of reloading procedures and a deep respect for the explosive potential of gunpowder.
Firearms are designed, manufactured and proof-tested to standards based on factory-loaded ammunition.
Handloaded or reloaded ammunition that deviates, either intentionally or accidentally, from load or component
recommendations can be very dangerous.
Reloaders must observe all possible safety precautions and practices related to the proper handling of explosives.
Whether you’re a seasoned reloader or just starting out, you should study the subject, watch reloading demonstrations
and talk to experienced reloaders.
The first rule of reloading is to always follow the manufacturer’s instructions for the components you’re using.
They’ll tell you to follow certain guidelines. Namely:
1. Don’t mix or substitute powders or primers.
2. Don’t use unknown or substandard components.
3. Use only suitable components that have been factory-tested
by reputable ammunition, powder and bullet manufacturers.
4. Always be sure to use the manufacturer’s recommended recipe when reloading.
Not following these guidelines could result in severe injury to yourself or severe damage to your firearm.
Dangerously high pressure and explosions can result from an overcharge of powder or other deviations from
established reloading guidelines. Be very careful. The process of reloading exposes you to environmentally
hazardous material. Lead, which is known to cause cancer and birth defects, is the most common substance
in bullets and shot. It is important to handle lead bullets and shot with extreme care. Work only in a wellventilated area and always wash your hands after exposure and before eating. Never smoke while reloading.
Primers and powders are also highly toxic and flammable. So after reloading be sure to clean up all materials
from your work area. Don’t leave primer or powder spills anywhere on the floor or bench top. Dispose of all waste
material in accordance with the manufacturer’s recommendations.
Finally, when reloading or handloading concentrate on what you’re doing at all times. Do not be distracted by
talking to others, listening to the radio or watching TV while reloading. Never reload after consuming alcoholic
beverages or drugs of any kind. You are working with extremely hazardous materials and you can’t risk even a
few seconds of distraction. Remember
for the performance and safety of your reloaded ammunition.
, if you reload, you are the ammunition manufacturer and you are responsible
®
4
Page 5
6th COMMANDMENT
If Your Gun Fails to Fire When the Trigger is Pulled, Handle With Care.
If for some reason the ammunition doesn’t fire when you pull the trigger, stop and remember the 1st
Commandment of Firearm Safety – always keep the muzzle pointed in a safe direction. Keep your face away from
the breech, then put the safety on, carefully open the action, unload the firearm and dispose of the cartridge safely.
Remember that anytime there’s a shell in the chamber, your gun is loaded and ready to use. Even if you tried to
shoot and your gun didn’t fire, treat your firearm as if it could still discharge.
7th COMMANDMENT
Always Wear Eye and Ear Protection When Shooting.
Your sight and hearing risk injury from shooting and should be protected at all times.
Wear protective shooting glasses to guard against falling shot, clay target chips, powder
residue, ruptured cartridge cases and even twigs and branches in the field. Also be sure
to wear eye protection when you’re disassembling or cleaning a gun so that tensioned
parts (like springs) and cleaning solvents don’t come in contact with your eyes. Continued
exposure to shooting noise can permanently damage your hearing. On the range, where
shooting volume is the loudest, be sure to use the maximum protection of a headset. And learn to use ear protection in
the field, especially in confined locations like duck blinds.
8th COMMANDMENT
Be Sure the Barrel is Clear of Obstructions Before Shooting.
Before loading your gun, open the action and make sure there’s no ammunition in the chamber or magazine. Check
the barrel for any obstructions or debris. Even a small amount of snow, mud, excess lubricant or grease in the bore
can dangerously increase pressure and cause the barrel to bulge or burst when firing. Use a
cleaning rod and patch to wipe away anti-rust compounds or any other residues or obstructions in the barrel.
Never try to shoot out an obstruction by loading another shell and firing!
When firing, rely on your instincts. If the noise or recoil of your firearm seems weak, stop everything, unload your
firearm and be sure nothing is lodged in the barrel. Remember the 12/20 burst? That’s what can happen when the
barrel is obstructed. So always be sure you’re using the correct ammunition in your firearm and that it’s free of
obstructions.
9th COMMANDMENT
Don’t Alter or Modify Your Gun and Have it Serviced Regularly.
Your firearm has been designed to operate according to certain factory specifications. You’ll jeopardize your safety
and that of others around you by attempting to alter its trigger, mechanical safety or other mechanisms. So never
alter or modify your firearm in any way.
Like any mechanical device, a firearm is subject to wear. It must be maintained and
periodically serviced to assure optimum safety and performance. Only a qualified
service facility should service, repair or modify your Remington
your instruction book for instructions on how to send your firearm to the factory or
for the location of the nearest Remington Authorized Service Center.
Proper cleaning and lubrication are also important to firearm maintenance and are
necessary to assure accuracy, safety and reliability. Before cleaning, always make
sure that your gun is completely unloaded. And always clean the barrel from the
chamber end to the muzzle when possible.
5
®
firearm. Consult
Page 6
Make it a practice to clean your bore every time you’re going to shoot. Be sure to clean your entire gun before
and after long-term storage and no less than once a year. It’s also important to clean your gun whenever it’s been
exposed to adverse conditions such as rain, dirt, mud, snow, sleet or saltwater.
For safe and dependable operation of your firearm, all parts of your gun must be properly cleaned and lubricated. Periodically inspect the internal workings of your firearm to be sure they’re clean and free of rust, unwanted
dirt and debris.
Use recommended lubricants on your gun and do not over-lubricate. Excessive use of a non-recommended
lubricant could adversely affect the function and safe operation of your firearm. Remember, you are responsible
for the proper care and maintenance of your firearm. Failure to properly maintain your firearm can not only
damage or ruin your firearm, it can expose you and others to unnecessary risks of personal injury or death.
Remington®has a wide range of firearm care products and resources for best results when cleaning your gun.
Everything from solvents and lubricants to rods and patches. They’re all available from your Remington dealer.
10th COMMANDMENT
Learn the Mechanics and Handling Characteristics of Your Firearm.
Not all guns are alike. They have different mechanical characteristics that dictate how you should carry and handle
them. Anyone who plans to use a firearm should first become totally familiar with the type of firearm it is and
the safe handling procedures for loading, unloading, carrying, shooting and storing it.
Before you even unpack your new Remington firearm, read this instruction
book from cover to cover and familiarize yourself with the different component parts of the gun. Then read, understand and follow the Ten
Commandments of Firearm Safety in this book.
ARNING!
W
firearms or handling ammunition may result in exposure to lead, a
substance known to cause birth defects, reproductive harm, cancer and
other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure.
Discharging firearms in poorly ventilated areas, cleaning
SHOOT SOBER!!
There’s one other rule that must be followed when handling firearms. In fact, respect for this rule is necessary in
order to effectively practice the Ten Commandments of Firearm Safety. The rule is: SHOOT SOBER! Guns and
alcohol or drugs make a deadly combination. Never consume anything that would mildly impair your judgment
or physical coordination when you’re using a firearm. A staggering percentage of the shooting accidents that
occur every year involve alcohol or drugs. Be smart. Always shoot sober and stay alive.
WARNING!
bystander and damage to property. Do not use a firearm until you fully understand and practice the Ten
Commandments of Firearm Safety. If you have any questions about the safe use of a Remington firearm, write
to us at Remington Arms Company, Inc., Consumer Service, P.O. Box 700, Madison, NC 27025-0700, or call
us at 1-800-243-9700.
DON’T KEEP THIS TO YOURSELF.
Now that you’re a gun owner you have the obligation to help ensure that shooting sports are safe for everyone
– participants and bystanders alike. You can do that by practicing these principles of firearm safety and passing
them on to others – especially new shooters. Set an example for beginners. Be a guide to their safe entry into
the exciting world of shooting sports. Invest your time and patience for the love of the sport and for its future.
After all, it’s your love of the sport that led you to buy a new Remington.
Firearm ownership is a right and privilege. It’s a right guaranteed in this nation’s Constitution. It’s a privilege
which carries with it a personal responsibility to use your firearm in a way which will ensure your safety and the
safety of others. The preser
your fellow shooters to the safe and responsible use of firearms. Let the Ten Commandments of Firearm Safety
outlined in the book guide you at all times. Teach and promote these rules whenever you can. Remember, firearm
safety depends on you! That’s the only way to really enjoy your new Remington firearm and to preserve sport
shooting as we know it today.
Failure to follow any of these safety rules may cause personal injury or death to the shooter or
vation of this right and privilege depends on the personal commitment of you and
Page 7
Remington®Model SP-10™Magnum Autoloading Shotgun
Congratulations on your choice of a Remington.®With proper care, it should give you many years of dependable
use and enjoyment. For best results, we recommend that you use Remington Ammunition – the ammunition used
in factory testing your firearm against our exacting function and performance standards.
PICTURE 1
PICTURE 2 This picture shows the parts of the ammunition.
This picture shows the main parts of the REMINGTON SP-10™MAGNUM SHOTGUN.
The picture will aid in understanding the instructions in this book. See page 10 for instructions on changing choke tubes.
Stock
Receiver
Safety Mechanism
Breech Bolt
Ejection Port
Trigger
Carrier Release Button
Operating Handle
Fore-end
Barrel
Magazine Cap
SHOTGUN SHELL
Head
Gauge
Marking
10
GA
Primer
Front Sight
Important Parts of the Firearm
The Safety Mechanism
The safety mechanism on the Model SP-10 Magnum Shotgun is a button located behind the trigger. See
Pictures 3 and 4.
The safety mechanism provides protection against accidental or unintentional
discharge under normal usage when properly engaged and in good working
order.
To engage the safety mechanism, push the button so that the
MARKING CANNOT BE SEEN.
Always engage the safety mechanism when the firearm is loaded and you
do not intend to shoot.
Never pull the trigger when the safety mechanism is engaged.
When you are ready to fire the firearm, press the safety mechanism so that
RED BAND MARKING IS SHOWING.
the
Do not touch the trigger while
moving the safety mechanism. Your fingers and all other objects should be
kept outside the trigger guard and away from the trigger until you are actually ready to fire by pulling the trigger.
WARNING:
The firearm will fire when the trigger is pulled and the
BAND IS SHOWING.
Even when the safety mechanism is engaged, careless handling can cause the firearm to fire. See the Te n
Commandments of Firearm Safety
on page 2.
RED BAND
RED
SAFETY MECHANISM
PICTURE 4
TRIGGER
Muzzle
PICTURE 3
7
Page 8
The Security System
An external lock has been supplied with your firearm. The gun lock is a security device to help you prevent
unauthorized use of your firearm. The instructions for the safe and proper use of the gun lock are provided in
the packaging for your lock. READ AND FOLLOW THE INSTRUCTIONS for the gun lock. You may also obtain
the instructions and warnings for the gun lock on the Remington website at WWW.REMINGTON.COM. or by
calling Remington’s toll-free number at 1-800-243-9700.
THE USE OF THE LOCKING DEVICE IS NOT A SUBSTITUTE FOR SAFE GUN HANDLING AND STORAGE,
INCLUDING KEEPING THIS AND EVERY GUN UNLOADED AND LOCKED IN A SECURE PLACE WHEN NOT
IN USE. READ AND FOLLOW THESE AND OTHER SAFETY RULES IN THIS INSTRUCTION BOOK. FAILURE TO READ, UNDERSTAND AND OBEY THESE RULES CAN RESULT IN SERIOUS PERSONAL INJURY
OR DEATH TO YOU OR OTHERS. SEE THE TEN COMMANDMENTS OF FIREARM SAFETY ON PAGE 2.
The Operating Handle
The operating handle is used to pull the bolt rearward to a locked open position. See Picture 5.
WARNING:
6, the bolt is closed and the firearm can be fired.
When the operating handle is forward as shown in Picture
The Carrier Release Button
1. Point the firearm in a safe direction.
2. Engage the safety mechanism.
3.
CAUTION:
operating handle.
4. Push the carrier release button IN to close the bolt. See Picture 6.
Keep your fingers away from the ejection port and
RED BAND WILL NOT SHOW.
The Trigger
Pulling the trigger fires the firearm.
The weight of the trigger pull is preset at the factory.
All adjustments to the trigger and trigger plate assembly must be made by the factory or a REMINGTON
AUTHORIZED SERVICE CENTER.
ARNING: NEVER
W
put your finger on the trigger unless you are going to fire the firearm.
PICTURE 5
OPERATING HANDLE
PICTURE 6
CARRIER
RELEASE BUTTON
CARRIER
®
The Barrel
The inside of the barrel must be clean and free of obstructions.
I. TO CHECK THE INSIDE OF THE BARREL:
WARNING:
MAGAZINE TO MAKE SURE THERE ARE NO SHELLS IN THE FIREARM.
1. Point the firearm in a safe direction.
2. Engage the safety mechanism. Make sure the
3. Pull the operating handle fully rearward until the bolt is locked open.
4. Insert a cleaning rod into the muzzle. Push the rod completely through the barrel until rod can be seen in
II. TO REMOVE OBJECT FROM INSIDE THE BARREL:
W
the barrel to burst or a cartridge case to rupture and cause serious personal injury.
1. Remove the barrel following instructions shown on pages 12 and 13.
2. Use the correct cleaning rod.
3. Insert cleaning rod into the muzzle and lightly tap rod to free object(s).
MAKE SURE THE FIREARM IS UNLOADED. LOOK INTO THE EJECTION PORT. CHECK THE CHAMBER AND
RED BAND IS NOT SHOWING.
the ejection port.
ARNING: NEVER
try to remove an object from the barrel by loading another shell and firing. This may cause
Page 9
4. If an object cannot be easily pushed out of the barrel with a cleaning rod, return the firearm to the factory or a
REMINGTON AUTHORIZED SERVICE CENTER.
III. TO CLEAN THE BARREL AND CHOKE TUBE FOLLOW THE INSTRUCTIONS SHOWN ON PAGES 12 AND 13.
BEFORE LOADING THE FIREARM
1.
Make sure the inside of the barrel is free of dirt or other objects.
2.
Check the condition of the gas system parts. See Picture 7. The gas cylinder must slide freely on the gas piston. If not, see page 13 for cleaning instructions.
To Change the Choke Tube
WARNING: UNLOAD
zine
EMPTY.
1. Point the firearm in a safe direction.
2. Engage the safety mechanism. Make sure the
3. Place the choke tube wrench into the choke tube.
4. Turn the wrench counterclockwise and remove the choke tube.
5. Select the desired choke tube and insert the tube into the barrel.
6. Tighten the choke tube snugly but
7. With the bolt open and the chamber and magazine empty, check the choke tube occasionally to make sure it
has not loosened.
NOTE:
NEVER fire the firearm without the choke tube installed.
the firearm before changing choke tubes. Leave the action
RED BAND IS NOT SHOWING.
DO NOT OVER-TIGHTEN.
OPEN
and the chamber and maga-
SLING STRAP ASSEMBLY
OPERATING HANDLE
CARDBOARD PACKING
RING
GAUGE MARKING
BARREL ASSEMBLY
CHOKE TUBES
GAS PISTON
GAS CYLINDER
To Assemble
The SP-10™ MAGNUM is shipped with the barrel and operating handle
CHOKE TUBE WRENCH
RAISE BOLT TO INSTALL
OPERATING HANDLE
PICTURE 7
removed. See Picture 7 for location of parts.
NOTE:
The barrel and chamber should be cleaned before assembling the
firearm. Clean the barrel following the instructions on page 16.
PICTURE 8
1. Point the firearm in a safe direction.
2. Engage the safety mechanism.
RED BAND WILL NOT SHOW
.
3. With the receiver assembly position as shown in picture 8, raise the bolt and insert the operating handle fully
into the slot in the slide.
Pull the operating handle fully rear
4.
ward to open the action.
5. Unscrew and remove the fore-end cap.
Slide the fore-end for
6.
ward and remove it from the slide extension assembly
.
7. Remove the cardboard packing ring from the end of the magazine tube extension.
8. Make sure that the slide extension assembly prongs are inside the holes in the front of the receiver.
9
9
Page 10
9. Hold the barrel in front of the gas piston. See Picture 9.
10. Slide the gas piston over the end of the magazine tube extension
and, at the same time, guide the barrel into the receiver..
BARREL LOCA
BARREL SLOT
RECEIVER COLLAR
TOR
PICTURE 9
GAS PISTON
11. Align the barrel slot with the barrel locator and seat the barrel
firmly into the receiver.
12. Slide the fore-end over the barrel lug and the slide extension
assembly.
SLIDE EXTENSION ASSEMBLY
MAGAZINE TUBE EXTENSION
13. Locate the rear of the fore-end into the receiver collar.
14. Replace and tighten the fore-end cap.
FULLY ASSEMBLED SP-10 MAGNUM
To Load and Unload
WARNING:
I. TO LOAD ONE SHELL ONLY:
1. Point the firearm in a safe direction.
2. Engage the safety mechanism.
3. Pull the operating handle fully rearward until the bolt is locked
4. Put one 10 gauge 3 1/2” Magnum shell through the ejection
5.
6. Push in on the carrier release button to close the bolt. See Picture 6 on page 8.
THE FIREARM IS NOW LOADED.
7. To fire the firearm, point in the direction of the intended target and then disengage the safety mechanism.
THE FIREARM IS NOW READY TO FIRE BY PULLING THE TRIGGER.
8. Pull the trigger to fire the firearm. The bolt will remain open after the firearm is fired.
9. Engage the safety mechanism when you are finished firing.
II. TO LOAD THE CHAMBER AND MAGAZINE:
W
ARNING:
1. Point the firearm in a safe direction.
2. Engage the safety mechanism.
3. Pull the operating handle fully rearward until the bolt is locked open.
4.
5.
6.
THE FIREARM IS NOW LOADED.
7. Push in on the carrier release button and press another shell
Before loading, always make sure the ammunition you intend to use is the correct gauge and length.
RED BAND WILL NOT SHOW.
open.
port. See Picture 10.
CAUTION: Keep your fingers away from the ejection port and
operating handle.
RED BAND WILL SHOW.
Before loading, always make sure the ammunition you intend to use is the correct gauge and length.
RED BAND WILL NOT SHOW.
Put one 10 gauge 3 1/2” Magnum shell through the ejection port. See Picture 10.
CAUTION:
Keep your fingers away from the ejection port and
PRESS IN MOMENTARILY
operating handle.
Push in on the carrier release button to close the bolt. See
Picture 6 on page 8.
against the carrier until the carrier starts to move. See Picture
11.
DROP SHELL
ONTO CARRIER
PICTURE 10
PICTURE 11
10
Page 11
8. Release the pressure on the carrier release button and continue pushing the shell fully forward into the
magazine tube.
9. Repeat steps 7 and 8 and push one more shell of the correct gauge fully forward into the magazine tube.
10. Make sure that after loading the last shell, the carrier returns to its latched position.
WARNING:
back over the carrier.
If the shell slides back over the carrier:
• Keep the firearm pointed in a safe direction.
• Forcefully
•
• When the chamber is loaded, firing the gun will CLEAR the jammed shell.
THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED.
11. To fire the firearm, point in the direction of the intended target and then disengage the safety mechanism.
THE FIREARM IS NOW READY TO FIRE BY PULLING THE TRIGGER.
12. Pull the trigger to fire the firearm. The firearm will fire each time the trigger is pulled until the magazine
13. Engage the safety mechanism when you are finished firing.
12. Look into the ejection port to make sure there are no shells inside the receiver, chamber or magazine.
Be sure the rim of each shell snaps past the end of the shell stop to prevent the shell from sliding
OPEN
the action, or
REMOVE
RED BAND WILL SHOW.
and chamber are empty. The bolt will remain
the trigger plate assembly following the instructions on pages 14 and 15 and remove the shell, or
OPEN
when the last shell is fired.
To Unload the Firearm
1. Point the firearm in a safe direction.
2. Engage the safety mechanism.
3. Pull the operating handle fully rearward to remove the shell from the chamber.
4. Close and open the bolt until all shells are removed.
WARNING:
Check the chamber and the magazine to make sure there are no shells remaining in the firearm.
RED BAND WILL NOT SHOW.
To Disassemble
WARNING:
firearm.
1. Point the firearm in a safe direction.
2. Engage the safety mechanism.
3. Pull the operating handle fully rearward until the bolt is locked open.
4. Unscrew and remove the fore-end cap.
5. Slide the fore-end forward and remove it from the firearm.
6. Hold the barrel in front of the gas piston and pull the barrel
7. Slide the slide extension assembly forward and remove it from
8. Allow the bolt to move forward GENTLY by holding the operating
9. Lift the bolt up and pull the operating handle out of the slide.
10. Tap out the front and rear trigger plate pins.
11. Press in and hold the carrier release button and at the same time lift rear of the trigger plate assembly and
WARNING: DO NOT
best be assured by keeping the safety mechanism engaged at all times.
Unload the firearm. Check the chamber and the magazine to make sure there are no shells in the
RED BAND WILL NOT SHOW.
assembly from the receiver.
the magazine tube.
handle while pressing the carrier release
slide it rearward out of the receiver. See Picture 12.
allow the hammer to snap forward when the trigger plate assembly is removed. This can
button.
PRESS IN AND HOLD
RED BAND WILL NOT SHOW.
11
SLIDE OUT
LIFT
PICTURE 12
Page 12
12. Use a phillips head screwdriver to loosen the top recoil pad screw,
then unscrew the lower recoil pad screw and rotate the recoil pad
to expose the stock bolt.
13. Use a 1/2” hex, socket to unscrew the stock bolt and remove the
stock from the action spring tube.
14. Place a rod through the hole in the action spring tube and unscrew
and remove the action spring tube and action spring from the
receiver. See Picture 13.
CAUTION: The action spring tube is under spring tension.
15. Grasp the action spring plunger and pull the slide assembly and
bolt to the rear of the receiver.
16. Reach into the receiver and hold the front of the slide and while
pushing forward on the link, pivot the slide up and out of engagement with the bolt cam pin. See Picture 14.
17. Remove the slide assembly from the receiver, by pulling it forward through the action spring tube hole.
18. Push the bolt forward out of the receiver.
19. Place a small screwdriver at an angle against the corner of the
shell stop pivot pin and tap lightly with a hammer to loosen. See
Picture 15. Be careful not to damage the receiver.
20. Reach inside the receiver and push the shell stop IN against
spring pressure and remove the pivot pin. Then remove the shell
stop and spring.
NOTE: There is normally no need to remove the magazine follower
assembly when cleaning the firearm. However, if this is desired, the
brass magazine follower plunger must be depressed and the assembly
rotated so that the plunger is held depressed by the magazine tube
wall. The magazine follower assembly and the magazine spring can
then be pushed rearward out of the magazine tube.
ROD WITH TAPERED END
PIVOT UP OUT OF BOLT
SLIDE
LINK
PICTURE 13
PICTURE 14
ACTION SPRING
PLUNGER
PICTURE 15
TAP LIGHTLY
NOTE: The magazine tube is permanently bonded to the receiver and no attempt should be made to remove it.
Lubrication and Maintenance
WARNING:
always look into the ejection port and check the chamber and the magazine to make sure the shotgun
is completely unloaded.
CLEANING
The amount of shooting between cleaning will vary greatly depending on
climate, weather conditions, ammunition used and the amount of lubrication. The gas system parts and the front face of the bolt should be
cleaned more frequently than the rest of the firearm.
TO CLEAN THE BARREL:
1. Use the instructions and equipment provided in a good cleaning kit.
2. Select the correct gauge cleaning brush and attach the brush to
3. Put the cleaning brush into gun-cleaning solvent.
4.
5. Remove the brush from the rod, attach tip with cleaning patch
6.
7.
Never attempt to clean or perform maintenance on a loaded firearm. Before cleaning,
®
For recommendations, see your Remington
Authorized Service
Center.
the cleaning rod.
Push the cleaning rod through the barrel several times.
and push through the bore.
Repeat several times, using a new
, clean patch each time until the
patch is not dirty.
Remove all of the shooting residue from the locking notch in the
barrel. See Picture 16.
REMOVE SHOOTING RESIDUE
GAS CYLINDER RETAINER
GAS PISTON
GAS CYLINDER
PICTURE 16
PICTURE 17
GAS PISTON
LOCKWASHER
GAS PISTON
NUT
Page 13
8. Clamp the barrel lug in a suitable holding device or, with the barrel
upside down carefully clamp the vent rib in a smooth jawed vice.
See Picture 17.
9. Using a 15/16” open end wrench, unscrew and remove the gas
piston nut and lockwasher. Pull the gas system assembly out of
the barrel lug.
10. Check the gas hole in the barrel. Use a 3/32" diameter wire to
clean the gas hole. See Picture 18.
BARREL LUG
3/32” DIA.
WIRE
PICTURE 18
GAS HOLE
WARNING:
After cleaning, make sure the barrel is free of obstructions.
THE GAS PISTON AND GAS CYLINDER
1. Pry off the gas cylinder retainer and remove the gas cylinder from the gas piston. See Picture 17.
2. Scrub both parts using steel wool and cleaning solvent until all powder residue has been removed. Wipe
clean and dry.
TO CLEAN THE CHOKE TUBE:
1. Remove the choke tube from the barrel.
2. Clean the choke tube, including the threads, with gun-cleaning solvent and wipe dry.
3. Apply Rem™ Oil on threads and reassemble choke tube to the barrel following instructions on page 9.
WARNING:
After cleaning but before using or storing, make sure the barrel is free of obstructions.
THE BOLT ASSEMBLY:
Brush the bolt assembly with cleaning solvent and wipe clean and dry. Pay particular attention to the front face
of the bolt which must be keep clean and smooth at all times in order to prevent feeding malfunctions. This surface should be cleaned frequently, which can also be accomplished without disassembling the firearm. While
holding the bolt handle rearward, reach through the ejection port and wipe the bolt face clean.
THE SLIDE ASSEMBLY:
Brush the slide, link and action spring plunger with cleaning solvent and wipe clean and dry. Apply a small
amount of gun grease to the bolt cam pin track in the slide.
THE SHELL STOP:
SLIDE EXTENSION BUFFER
PICTURE 19
Brush the shell with solvent and wipe clean and dry.
THE SLIDE EXTENSION ASSEMBLY:
Brush the slide extension assembly with solvent and wipe clean and dry.
SLIDE EXTENSION ASSEMBLY
NOTE: Check the condition of the slide extension buffer and replace if worn or damaged. See Picture 19
.
THE TRIGGER PLATE ASSEMBLY:
SPRAY WITH Rem™ Oil
AS SHOWN
PICTURE 20
NOTE: Clean as a unit with Rem™ Oil as shown. See note on page 15.
Spray the trigger plate assembly with Rem™ Oil as shown. See Picture
20. Let stand for 15 minutes. Spray again to wash off components.
Shake off excess lubricant.
ARNING:
W
Excessive use of a non-recommended lubricant could cause serious function problems possibly lead
DISCONNECTOR
(BELOW CONNECTOR)
CONNECTOR
ing to accidental firing.
13
-
Page 14
THE RECEIVER ASSEMBL
Y:
1. Brush the inside of the receiver with cleaning solvent and wipe dry.
2. Clean the outside surface of the magazine tube with cleaning solvent, then wipe dry with a clean cloth.
How To Reassemble
1. With the receiver positioned on its side, hold the shell stop horizontally and install the shell stop spring in
the hole in the shell stop. See Picture 21.
2. Being careful not to dislodge the spring, install the shell stop
inside the receiver with the carrier release button area protruding
through the receiver slot.
3. Line up the shell stop slot with the shell stop pivot hole in the
receiver and install the shell stop pivot pin so that the angled surface blends with the receiver radius. Tap the end of the pin lightly
to seat it.
4. Install the bolt assembly through the front of the receiver and slide it to the rear of the receiver.
5. Install the slide assembly by passing the action spring plunger and link through the action spring tube
hole in the receiver. Then while holding the link, rotate the cam track of the slide over the bolt cam pin and
seat the slide inside the receiver.
6. Push the slide assembly and the bolt to the front of the receiver. Spray a small amount of Rem™ Oil into
the receiver.
7. Spray a small amount of Rem™ Oil into the action spring tube and install the action spring into the tube.
8. Place a rod through the hole in the action spring tube as shown in picture 13 on page 11, then position the
action spring plunger inside the action spring and screw the action spring tube into the receiver. Tighten
snugly and remove the rod.
9. Replace the stock over the action spring tube, then install stock bolt washer, lockwasher and stock bolt and
tighten securely.
10. Rotate the recoil pad to center it on the stock and tighten the two recoil pad screws.
11. Check the trigger plate assembly to make sure that the end of the disconnector is below the connector. See
Picture 20 on page 13.
12. Push IN and hold the carrier release button, and at the same time carefully insert the trigger plate assembly at an angle (carrier first) into the receiver. Then rotate it until the rear of the disconnector stops against
the receiver. See Picture 22.
13. While still holding the carrier release button IN, push the end of
the disconnector IN and complete rotation of trigger plate assembly until its bushing holes align with the holes in the receiver.
14. Tap in the front and rear trigger plate pins.
15. Lift upward on the bolt and install the operating handle fully into
the slot in the slide.
16. Pull the operating handle fully rearward to lock the bolt open.
17. Install the slide extension assembly over the magazine tube and position its two prongs in the mating holes
in the front of the receiver.
18. Install the gas cylinder parts on the barrel. See Picture 17 on page 12.
NOTE: Do not over
-tighten nut and compress the lock washer flat.
19. Hold the barrel in front of the gas piston as shown in picture 9 on page 9, and slide the gas piston over the
end of the magazine tube extension, and at the same time guide the barrel into the receiver.
20. Align the barrel slot with the barrel locator and seat the barrel firmly into the receiver.
Slide the fore-end over the barrel lug and slide extension, and locate its rear end in the receiver collar
21.
22. Replace and tighten the fore-end cap.
SHELL STOP SPRING
SLOT
PUSH IN
PICTURE 21
SHELL STOP
PICTURE 22
REAR OF
DISCONNECTOR
.
WARNING: This firearm should be checked periodically by the Remington Arms Company, Inc. or a REMINGTON AUTHORIZED SERVICE CENTER. This will insure proper inspection and any necessar
y replacement of worn
or damaged parts.
14
Page 15
Lubrication:
Over-lubrication should be avoided at all times. A thin coat of Rem™ Oil is all that
is needed to prevent the possibility of rusting. See
When the firearm is to be stored, it should be carefully cleaned and thoroughly oiled.
Outside surfaces should be wiped with a light coat of Rem™ Oil occasionally. See
NOTE below.
When firearm is to be reused, all excess lubrication must be removed. The chamber and bore must be
thoroughly wiped dry.
NOTE:
Remington Rem™ Oil is available from your local dealer. If your dealer is out of stock, ask him
to order Rem™ Oil from his Remington distributor.
NOTE below.
15
Page 16
How to Obtain Parts and Service From Remington®Arms Co.
TO ORDER PARTS:
Many Remington Dealers and Authorized Service Centers carry a full line of parts. Please check with them first
before ordering parts.
To expedite your PARTS order or request REPAIR SERVICE visit our web site at www.remington.com. Detailed
instructions are provided along with parts and/or service order forms. You may also reach Remington by calling
our toll free customer service number, 1-800-243-9700, Mon.-Fri., 9:00 AM-5:00 PM Eastern time.
1. Fax completed order form (from the web site) to 1-336-548-7801.
2. To order by phone without the order form call 1-800-243-9700.
Please have the following information ready before you call.
• Firearm model and serial number.
• Part description and quantity. Part descriptions can be found on the parts listing page in this manual.
• Your complete mailing address (P.O. Box and Street Address) including zip code, telephone
number and e-mail address.
• Method of payment: Mastercard, Visa, Amex or Discover card number and expiration date. Prepayment
may be made by check or money order. A quote may be made to you over the phone. (Sorry, no C.O.D.s.)
WARNING!
NOTE:
requested via our web site at: www.remington.com or by calling 1-800-243-9700.
1. To locate the Remington Authorized Service Center nearest you visit our web site at www.remington.com and
USE ONLY REMINGTON PARTS IN REMINGTON FIREARMS.
SOME PARTS MAY BE RESTRICTED. See parts list for details. Owner’s manuals/instruction books may be
REPAIR SERVICES
use our Repair Service Locator. If you need additional on-line assistance, e-mail us at info@remington.com
to obtain a listing of Remington Authorized Service Centers. Contact the Remington Authorized Service
Center of your choice for evaluation of your firearm and/or additional shipping instructions.
2. If your Remington Authorized Service Center cannot provide the service or repair you require and you need
further assistance, please call our toll free number 1-800-243-9700, Mon.-Fri., 9:00 AM-5:00 PM Eastern
time and select the option for repairs. Then, if shipment of your firearm is required, please:
• Record the serial number of your firearm before sending it to us.
• Pack your firearm for safety and to prevent further damage in shipping and handling. Preferably, ship in a
firearm box.
• Remove all accessories from the firearm to prevent loss or damage.
• Enclose a letter with the firearm detailing the model name or number of your firearm and serial number
along with a full description of the problem. Be sure to include your full name and address (P.O. Box and
Street Address), including zip code, daytime telephone number and e-mail address.
• Ship your firearm by either United Parcel Service (UPS) or Parcel Post (US Post Office). Remington is not
responsible for damage or loss during shipment, so you may elect to purchase insurance from your carrier.
Ship to:
Remington Arms Company, Inc.
Attn: Arms Service Division/Repairs
14 Hoefler Ave.
Ilion, NY 13357
WARNING!
THE SAME BOX WITH THE FIREARM. THIS IS A VIOLATION OF FEDERAL LAW.
IF YOU FEEL YOU MUST SEND SPENT SHELLS, PLEASE SEND THEM IN A
SEP
TELEPHONE NUMBER, MODEL AND SERIAL NUMBER OF YOUR FIREARM.
DO NOT SEND LIVE OR SPENT SHELLS IN YOUR FIREARM OR IN
ACKAGE AND INCLUDE NAME, ADDRESS (WITH ZIP CODE),
TE P
ARA
16
Page 17
MODEL SP-10™MAGNUM
Autoloading Shotgun
29
14
72
71
74
75
77
73
76
51
50
51
3
4
1
17
31
84
18
78
84
79
84
13
55
56
80
57
54
33
30
49
12
58
60
59
81
53
47
5
6
35
34
32
22
70
2
16
15
63
83
19
83
39
38
11
37
52
82
40
64
61
62
36
10
9
82
7
24
23
65
69
41
44
43
42
68
25
20
21
8
66
48
70
45
46
67
28
26
27
17
Page 18
MODEL SP-10™Magnum
Autoloading Shotgun
PARTS LIST
PART NAME VIEW #PART NAME
VIEW
#
NOTE:
Parts subject to change without notice
FOB Ilion, New York.
1 Action Spring
2 Action Spring Plunger
3 Action Spring Tube Assembly
4 Barrel Assembly
5 Bolt
6 Bolt Assembly
7 Bolt Buffer
8 Bolt Cam Pin
9 Carrier
10 Carrier Assembly
11 Carrier Dog
12 Carrier Dog Pin
13 Carrier Dog Spring
14 Choke Tube
15 Collar
16 Collar Screw (2)
17 Disconnector
18 Disconnector Spring
19 Ejector
20 Extractor
21 Extractor Plunger
42 Extractor Spring
22 Firing Pin
23 Firing Pin Retaining Pin
24 Firing Pin Spring
25 Fore-End
26 Fore-End Assembly
27 Fore-End Cap Assembly
28 Fore-End Washer
29 Front Sight
30 Gas Cylinder
31 Gas Cylinder Retainer
32 Gas Lug Pin
33 Gas Piston
34 Gas Piston Lockwasher
35 Gas Piston Nut
36 Hammer
37 Hammer Pivot Pin
38 Hammer Plunger
39 Hammer Spring
Magazine Follower
40
41 Magazine Follower Assembly
Magazine Follower Plunger
42
43 Magazine Follower Plunger Spring
Magazine Follower Plunger Retaining Pin
44
45 Magazine Tube Sub-Assembly
Magazine Spring
46
47 Middle Sight
48 Operating Handle
49 Receiver Sub-Assembly (Restricted)
(Includes # 19 & # 63)
50 Recoil Pad
51 Recoil Pad Screw (2)
52 Release Lever
53 Release Lever Spring
54 Safety Mechanism
55 Safety Mechanism Detent Ball
56 Safety Mechanism Spring
57 Safety Mechanism Spring Retaining Pin
58 Sear
59 Sear Pivot Pin
60 Sear Spring
61 Shell Stop
62 Shell Stop Pivot
63 Shell Stop Pivot Retainer
64 Shell Stop Spring
65 Slide
66 Slide Assembly
67 Slide Extension Assembly
68 Slide Extension Buffer
69 Slide Link
70 Slide Link Pivot (2)
71 Stock
72 Stock Assembly
73 Stock Bolt
74 Stock Bolt Lockwasher
75 Stock Bolt Washer
76 Stock Swivel Screw
77 Stock Swivel Screw Washer
78 Trigger Assembly (Restricted)
79 Trigger Pivot Pin
80 Trigger Plate Sub Assembly (Restricted)
81 Trigger Plate Assembly
82 Trigger Plate Pin Bushing (2)
83 Trigger Plate Pin (2)
84 Trigger Plate Detent Spring (2)
Page 19
Firearm Owner’s Record
Model _________________ Serial # ________________ Date Purchased ______________
Purchased From ___________________________ Price Paid _________________________
Remember to complete and return the Firearm Warranty Registration Card in order to
obtain full benefit of your Limited Two Year Firearm Warranty.
A WORD ON THE MAINTENANCE AND CARE OF YOUR REMINGTON FIREARM
Don’t Alter or Modify Your Gun and Have it Serviced Regularly.
Your firearm has been designed to operate according to certain factory specifications. You’ll jeopardize your
safety and that of others around you by attempting to alter its trigger, mechanical safety or other mecha-
nisms. So never alter or modify your firearm in any way.
Like any mechanical device, a firearm is subject to wear. It must be maintained and periodically serviced
to assure optimum safety and performance. Only a qualified service facility should service, repair or mod-
®
ify your Remington
to the factory or for the location of the nearest Remington Authorized Service Center. Remington recom-
mends that you have your firearm professionally serviced annually. You should also have your firearm
professionally serviced after prolonged storage, or if there is ever any question pertaining to the proper
functioning characteristics of your firearm.
firearm. Consult your instruction book for instructions on how to send your firearm
Proper cleaning and lubrication are also important to firearm maintenance and are necessary to assure
accuracy, safety and reliability. Before cleaning, always make sure that your gun is completely unloaded.
And always clean the barrel from the chamber end to the muzzle when possible.
Firearm Maintenance Record
DATE SERVICE PERFORMED PERFORMED BY
19
Page 20
Remington is a trademark registered in the United States Patent
and Trademark Office by Remington Arms Company
, Inc.
Printed in U.S.A.
Form RD 7073 Rev. 1004
Loading...