Remington DA-57, DA-757, DA-325, DA-107, DA-407 User Manual

...
0 (0)

®

How to get a great shave from your Remington® MicroScreen® 2 Shaver

Thank you for buying this premium shaver from Remington®.

Inside you'll find tips on using and caring for your shaver to get the best shave possible.

Model DA-757

(LCD Display)

Model Only

Model DA-57

(no LED)

Model DA-107

(no LED)

Model DA-307

Model DA-325

Model DA-407

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical shaver, basic precautions should always be observed, including the following. Read all instructions before using this shaver.

DANGER

To reduce the risk of electric shock:

Do not reach for a shaver that has fallen into water. Unplug immediately.

Do not use while bathing or in a shower.

Do not place or store shaver where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.

Except when charging, always unplug this shaver from the electrical outlet immediately after using.

Unplug this shaver before cleaning.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

A shaver should never be left unattended when plugged in, except when charging your rechargeable shaver.

Close supervision is necessary when this shaver is used by, on, or near children or invalids.

Use this shaver only for its intended use as described in this manual. Do not use attachments not recommended by Remington.

Keep the cord away from heated surfaces.

Never operate this shaver if it has a damaged cord or if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the shaver to a service center for examination and repair.

Never drop or insert any object into any opening.

Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

Do not use this shaver with a damaged or broken cutter or head, as facial injury may occur.

Always attach plug to shaver, then to outlet. To disconnect, turn all controls to “Off,” then remove plug from outlet, then detach power cord from the shaver for storage.

Always store your shaver and cord in a mois- ture-free area. Make sure your cord is disconnected from the shaver.

To prevent possible damage to the cord, do not wrap cord around the shaver.

Never put the shaver in direct sunlight or store in pouch at a temperature above 140° F.

“Household Use Only”.

SAVE THESE

INSTRUCTIONS

Remington DA-57, DA-757, DA-325, DA-107, DA-407 User Manual

Getting Used To Your Shaver

Congratulations on your purchase of a premium Remington® MicroScreen® 2 Shaver. It will give you years and years of close, comfortable shaves.

As with every shaver, your shave will improve over time. So allow about three weeks to develop an effective shaving style and for your skin to adjust to the new shaver.The adaptation period may take a little longer if your skin is sensitive, if you are switching from a different way of shaving, or if you alternate between shaving methods.

When you first removed your MicroScreen® 2 Shaver from its box, you may have noticed what appear to be small particles of white or gray powder on the MicroScreen or in or around the cutter assembly. The particles are from a coating of a special lubricant applied to the new foil and cutters to smooth breaking in your new shaver. They will disappear with use.

The Best Technique

It’s simple to get a great shave out of your new shaver. Here are a few tips for getting the closest shave possible:

Always use a clean, dry shaver.

Wait at least 15 minutes after rising

12

to allow the puffiness that most men

9 3

experience upon waking to disap-

6

pear.

Make sure your face is clean and dry before starting.

Hold the shaver so all foils touch your face together. This allows the shaver to provide for the closest shave and minimum foil wear. Avoid holding the shaver at an angle so only one foil touches the skin. This will distort the foil and may cause some skin irritation.

Use short, circular strokes

and use your free hand to stretch your skin. This encourages your whiskers to stand out, making it easier for them to enter the cutting mechanism.

Never press hard. Pressing only flattens your whiskers, which makes it harder for them to enter the cutting mechanism. It will also wear out the foils more quickly.

Shaving Longer Hairs

Your MicroScreen® 2 Shaver is equipped with a special push-up trimmer that allows you to shave stubborn long hairs on facial and neck areas or trim a beard or mustache quickly and

easily. Just push the trimmer button upward until the trimmer locks into position. Stroke the hairs being trimmed lightly. To extend battery life, turn off the trimmer while you are shaving.

For a Better Shave...

To help maximize your shaver’s performance, consider using the Remington® Pre-Shave Powder Stick (SP-5). Just rub it over your beard. It absorbs moisture and facial oils, helping set up the hairs so they enter the cutting chamber more easily. It makes shaving quicker and more comfortable.

Cleaning Your Shaver

TO ASSURE SMOOTH, EFFICIENT PERFOR - MANCE, IT IS IMPORTANT TO CLEAN YOUR SHAVER. Cleaning your Remington® MicroScreen®

2 Shaver is easy.

Remove the Head Assembly by holding onto the sides of the Head Assembly at the arrows and gently lifting the assembly away from the shaver.

Tap the base of the Head Assembly lightly on a flat surface. This should dislodge most of the hairs trapped within it. To guard against inadvertent damage, do not remove the Foil Assembly, except to replace it.

Next, clean the Cutter Assembly while it is still on the shaver. Hold the shaver and Cutter Assembly as shown, and, using the brush supplied, lightly brush and blow the hair clippings from between the blades.

Tip: To help reduce wear and tear, spray the foils and Head Assembly with Remington® Spray Shaver-Saver® Lubricant after every shave. This helps remove hairs while keeping your shaver operating smoothly.

Trimmer Care

The trimmer on your Remington® MicroScreen® 2 Shaver is easy to maintain.

■ When you clean your shaver, just brush off any clippings that may accumulate around the trimmer Assembly.

Using the longer bristles on the brush supplied will enable you to get into the area between the trimmer and the shaver.

Loading...
+ 2 hidden pages