Remcor DF250 Installation Manual
Ice Maker Adapter Kit (P/N 629084901) Installation Instructions
!
WARNING:
!
WARNING:
!
WARNING:
INSTALLATION INSTRUCTIONS
ICE MAKER ADAPTER KIT (P/N 629084901)
For Dispensers and the following ice maker model series:
Table 1. Applicable Models
Models
Remcor Model Series DF/ED200/250
Hoshizaki KML 200, 400, 600
Table 2. Loose Shipped Parts
Item No. Part No. Name Qty.
1 620032901 Ice Maker Adapter Lid 1
2 620032904 Manual Ice Fill Cover 1
3 15303 Ice Maker Mounting Bracket 2
4 50904 RTV, 3-oz. Tube 1
5 70226 No. 10 Sheet Metal Screw 6
6 70188 No. 8-32 Thumb Screw 1
7 91957 Label, “DISCONNECT POWER BEFORE CLEANING” 1
8 620913601 Installation Instructions 1
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the
user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer’s instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Remove the plastic dispenser lid and discard it.
2. Install the ice maker adapter lid as shown in Figure 1. Using the slotted holes in the lid as a template, drill four (4)
0.136” diameter holes at the bottom of the slots (refer to Detail A in Figure 2) into the dispenser cabinet. Secure
the lid to the cabinet with four (4) No. 10 sheet metal screws provided in the kit.
3. Seal the ice maker to the dispenser adapter lid as follows (refer to Figure 1).
A. Run a bead of RTV on the lid around the outline of the ice maker.
B. Set the Ice maker on to the lid and position as shown. Note: If the ice maker is being installed from
the front of the dispenser, use a piece of 3/4-inch diameter or larger PVC pipe as a “roller” to
slide the ice maker over the front “drip” flange of the dispenser lid.
C. Wipe away any excess RTV.
4. Secure the ice maker to the dispenser with two (2) brackets provided in the kit. Mount the brackets to the dispenser lid using the two rear screws, as shown in Figure 1. Using the brackets as templates, drill 0.136” diameter
Release Date: November 9, 2010 www.cornelius.com Revision: B
© 1998-2010, IMI Cornelius Inc. - 1 - Publication Number: 620913601
Ice Maker Adapter Kit (P/N 629084901) Installation Instructions
CAUTION:
!
holes into the Ice maker cabinet. Use caution not to drill into any Ice maker components (condenser, tubing etc.).
Secure the brackets to the ice maker cabinet using the No. 10 sheet metal screws provided in the kit.
5. Follow the manufacturer’s instructions to complete the installation of the ice maker, including the bin thermostat, if
so equipped or required.
The bin thermostat location must not interfere with the agitator rotation.
6. Install the caution label on the manual fill cover as shown in Figure 1. Secure the cover in position over the front
bin access opening by placing it over the drip flange lid on the lid (refer to Detail B of Figure 3). Note that with the
cover installed properly, it is held in position by the lid drip flange and cannot be removed without first lifting it over
the drip flange. Secure the manual fill cover to the adapter lid with the No. 8-32 thumb screws provided in the kit.
Publication Number: 620913601 - 2 - © 1998-2010, IMI Cornelius Inc.
Loading...