Page 1
Warning
Installation Guide ( MIC-800 )
C
COPYRIGHTS 1998 REMACO TECHNOLOGIES PTE LTD
WEBSITE: WWW.REMACOTECH.COM
S: MIC
Important Notes:
All products are thoroughly inspected and fully tested operational in factory. We accept no liability whatsoever for any losses due to improper operation, or any unauthorized alternation.
All trademarks contained in this installation guide are the property of their respective owners.
V: 3.0
Concept
The MIC-800, Media Interface Controller, is an electronic controller that can be used to link a variety of
audio-visual equipments in classrooms, training rooms & conference rooms. By using the MIC-800, the
selection of equipment will be just within a touch of a button.
Fig. 1
PROJ
ON/OFF
MIC
ON/OFF
VIDEO
PC BLANK WIRE
LESS
VOLUPVOL
DOWN
MUTE
PC 3 IN
PC 2
AUDIO IN
PC 2 IN
MONITOR OUT
PC 1
AUDIO IN
PC 1 IN
PC 3
AUDIO IN
VIDEO
IN
RL IN
AUDIO
6.35 mm
MIC IN
Fig. 2
Front Panal
V+ GN
Inner Board
Application
The MIC-800 has 3 D-Sub 15pin input ports for connection to 3 different sources, as well as a video and
microphone input port. All these ports will provide the monitor, speaker and projector output ports with the
desired audio and visual signals that is essential for any classroom or office setups.
Application
Power
For connection to a 230V power source
230V AC-DC
Adapter
Projector
Monitor
Computer 3
Computer 2
Computer 1
Microphone
Player
Speakers
Item
1
2 3
4
5
6
7
Page 2
End
Fig. 4
Inner Board
AUDIO
Audio output for connection to audio equipment
OPTIONAL PART -
AVA-258
Audio Cable
AUDIO
GN LR
PROGRAMMING FOR PROJECTOR
Initialization:
1) Press the MIC ON/OFF and PC button at the same time to enter programming mode. MIC ON/OFF and
Projector ON/OFF indicator lights will turn on.
2) Enter password 2215, a long beep will sound indicate ready for programming mode. Key in projector assigned code as
listed below (Example: for Panasonic Projector 2215 , long beep , 3 4).
means programming is successful.Once done, 2 short beeps will sound that
Projector Assigned Code Listing
1 1 3M X series, Hitachi
1 2 3M DX series, Hitachi
1 3 Acer
1 4 BenQ, HP
1 5 BenQ 7 series
1 6 Canon SX6 series
1 7 Dell
For Projector Brand not listed above, please use spare “user programmable code.”
3 1 NEC
3 2 Optoma EP757
3 3 Optoma 759
3 4 Panasonic
3 5 PLUS
3 6 Proxima
3 7 Sanyo
2 1 Epson current models
2 2 Epson older models
2 3 Fujitsu
2 4 Geha Compact 218
2 5 Geha Compact 288
2 6 Infocus
2 7 Mitsubishi
4 1 Sharp
4 2 Sony Ex series
4 3 Sony CX/FX/PX series
4 4 Toshiba
4 5 Viewsonic 558 series
4 6 Viewsonic 559 series
4 7 Geha Compact 228
7 1 User Programmable
7 2 User Programmable
* If communication fail, it may due to
1. F RS-232 connector, it will work.eedback loop waiting for acknowledgment. Remove “RX” pin on the MIC-800
Fig. 3
Inner Board
Application
VIDEO
VGA
RS-232
Video outputs and controls for connection to visual/audio equipments
Item
VD GN R G B H V
GN GN GN
RX TX GN
VIDEO
VGA
RS-232
OPTIONAL PART -
AVA-255
3-in-1
Video, VGA
& RS-232 Cable
* Press 3737 to enter programming mode. A long beep will sound ready for programming mode. Connect MIC-800
* Programming software (T Series software) can be download from Remaco Website to program the MIC. You will need
your projector protocol to program the MIC.
2. Projector RX/TX pin may connect wrongly, swap the RX/TX pin and it will work.
Remarks
* The 2 empty memories (7 1 and 7 2) are for programming projectors not found in the list.
RS-232 to computer RS-232 port (If RS-232 port is not available in computer, “ USB to RS-232 Converter ” can be used).
Loading...