Automatic Phone-Out Home Monitoring Systems
Power Outage and Freeze Alarm Model Number: THP202
Power Outage, Freeze and Flood Alarm Model Number: THP201
Product Description
These monitoring systems are intended to monitor homes, cabins, and ot her premises for power outage, low temperature
conditions and the presence of water. They are designed to automatically call up to three telephone numbers—such as
your cell phone, your cabin phone, your prim ary resid ence phone, or a neighbor’s phone-- when an alarm condition occurs.
Sensors for power outage and temperature, featured in Model Number THP202, are ho used in the main control panel. An
additional water sensor is housed in a separate plug-in a ccessory, which is included with Model Number THP201. The
water sensor can be placed up to 100 feet from the control panel using additional telephone line.
For each of the following three potentially damaging situations , this monitoring system will automatically dial up to three
user-programmed telephone numbers and advise the person answering that one or more of these conditions hav e been
detected:
• A power failure in the branch circuit that the control panel is plugged into
• A temperature drop to below 45
• The presence of water at the location of the optional water sensor probe (when plugged into the control
The person answering the call from the alarms can choose to either:
The monitoring system control panel must be located where is has access to an active Touch Tone™ or rotary/pulse
telephone line and a 120-Volt electrical outlet.
panel)
• Do nothing and allow the monitoring system to call every 15 minutes while alarm condition exists.
• “Acknowledge” the call and allow the monitoring system to continue to inform them of the alarm condition at
one hour intervals beginning with the first telephone c all and continuing until the alarm condition no longer
exists, or
• “Disable” the monitoring system and halt all monitoring and call ing feature s of this monitoring s ystem. WHEN
THE MONITORING SYSTEM HAS BEEN DISABLED, IT MUST BE RESET AT THE CONTROL PANEL
BEFORE THE MONITORING AND CALLING FUNTIONS WILL RESUME.
Parts List
Main Automatic Phone-Out Control Panel AC/DC Wall Voltage Adapter
3-Foot phone cord Plastic Wall Anchors (2)
Wall Anchor Screws (2) Velcro TM mounting pads (2)
9-Volt Battery Water Sensor (Model Number THP201)
Monitoring System Features
• Installs in minutes
• Clear voice message that specifies alarm type (temperature, power outage or flood) on the outgoing call
• Will call up to three programmed telephone numbers when an alarm condition occurs
•
Works on either rotary/pulse or tone telephone lines
• Monitors the outgoing telephone line to establish a dial tone before making an alarm call-out.
• Can select whether or not to monitor temperature.
• Can be set for either a 5 minute or 30 minute call out delay after an alarm condition is detected
• ON/OFF switch to disable the monitoring system when monitoring is not desired and to r e set the monitor ing s ystem
when “Disabled”.
• Visual indicator and audible signal when an alarm condition is detected
• Red LOW BATTERY indicator light on control panel
• Operates in an ambient temperature range of 32
• FCC Approved
• UL Listed wall outlet power adapter
• Water Sensor can be connected to up to 100 feet of phone cord to reach potential hazard area.
IMPORTANT - Read and thoroughly understand the instructions and warranty prior to
installation. The installation of these alarms requires that the monitoring system be
tested after installation to insure that the monitoring system is compatib le with both the
outgoing telephone line and the telephone(s) that will be called. This monitoring system
is an outgoing telephone device only and will not respond to any incoming telephone
calls.
o
F +/-3oF (7oC +/- 2oC) at the control panel
o
F to 175oF (0oC to 80oC)
Control Panel Components
Installation Instructions
Tools Required
#2 Phillips screwdriver for wall anchors, #1 Phillips screwdriver for cov er retaining screw and 3/16” drill if attaching the
mounting base using the included Phillips scre ws and wall anchors. Only scre wdriver for cover retaining screw is required
if you use the Velcro
Step-by Step Installation Procedure
1. Remove all packaging.
2. Remove the cover retaining screw on the front of the unit.
3. Remove the mounting base from the back of the monitoring system control panel by
pressing button on the control panel to release. (See diagram in STEP 3).
4. Install supplied 9 V alkaline battery in battery compartment of control panel.
IMPORTANT - When first installing or changing the battery, disconnect all phone
lines from the alarm control panel. Battery must be alkaline.
5. Choose to maintain or disable the factory pre-set low-temperature (TEMP) alarm function
located inside the main control panel. The alarm is pre-set to ON.
With the control panel removed from the mounting base, locate the dipswitch on the
circuit board. (See photo in STEP 5)
• To de-activate the low-temperature alarm, slide the TEMP switch away from the ON
The alarm can be re-activated at any time by sliding the switch to the ON position.
6. Set Pulse/Tone switch on top of monitoring system control panel housing to match your
phone system. (See diagram for STEPS 6 & 7).
7. Set “Call Delay Time” switch on top of control p anel housing for the desired delay time the
monitoring system is to wait before making the first outgoing telephone call to indicate an
alarm condition. Choose either 5 or 30 minutes. (See diagram for STEPS 6 & 7).
8. Locate a suitable location for the mounting base of the monitoring system control panel,
preferably within three feet of both an accessible telephone jack and a 120-Volt electrical
outlet. If installing beyond three feet from the telephone ja ck, you will need to purchase a
longer telephone cord. Install mounting base with screws (included) or Velcro strips
(included). Use anchors if installing into drywall or plaster. For appearance, adjust as level
as possible. (See diagram for STEP 8.)
9. Repl ace the monitoring system control panel on its mounting base by fitting then snapping
into place. Insert the cover screw in the hole to the right of the on/off switch and tighten,
securing the control panel to the base.
10. Connect telephone cord to the "To Wall Phone Jack" on the bottom of the control panel
housing (3 foot telephone cord is included)
11. Connect answering machine, telephone, or fax
machine to the "To Phone" jack on the bottom of
the control panel housing using an existing
telephone cord.
12. Plug AC adapter into a 120-Volt electrical outlet.
Insert the plug on the AC adapter into the
“Power Jack” on the bottom of the control panel
housing.
13. If using the remote water sensor, plug the
telephone line from the water sensor into the
"Water Sensor Jack". Additional telephone line
up to 100 feet (purchased separately) can be
patched between the control panel and the
Water Sensor. Do not exceed 100 feet.
TM
position.
strips provided.
STEP 5
Programming the Outgoing “Call-To” Telephone Numbers
Now that you have installed your monitoring system, you are ready to
program the outgoing telephone numbers to be called during an
alarm condition—such as your cell phone, your cabin phone, your
primary residence phone or a neighbor’s phone. Before you begin
the simple step-by-step programming procedure below, check and
confirm that:
• The ON / OFF switch on the control panel is in the ON position.
• The monitoring system control panel is properly connected to the
wall adapter and phone lines, and that the Water Sensor is
properly connected for Model THP201 only.
• If the monitoring system has been idle for a long period, install a
fresh 9V alkaline battery. The installed battery will discharge
when the monitoring system has no AC power even when the
monitoring system is turned off.
To program the first outgoing telephone number:
1. Press and hold the “1” key on the keypad for 10 seconds until
the “system armed” green light blinks two times and then stays
off.
2. Release the “1” key. Using the keypad, enter the first outgoing telephone number (maximum of 12 digits).
3. Press and hold the “#” key for 10 seconds until the green light blinks twice and then stays lit.
4. The green light should stay lit to indicate the number was properly programmed and retained in memory. If not,
repeat steps 1 through 3.
Note: Programming over a number already in memory will replace the number in memory.
To program the second and third outgoing telephone numbers:
Repeat steps 1 through 4 above except press the “2” key to designate the second outgoing number, and the “3” key to
designate the third outgoing number.
Outgoing Number Calling Sequence
When an alarm condition is first detected, the monitor ing system will call the first programmed outgoing telephone n umber
that it locates. It will always scan in sequence “call-to” location 1, location 2, and location 3. If a telephone number is not in
location 1, but does exist in location 2, then the location 2 programmed telephone number will be the first telephone
number the monitoring system will call with the alarm message. It is not necessary to program all three telephone n umbers
for the monitoring system to work properly.
Reprogramming or Clearing All Programmed Telephone Numbers
Programming over the number in memory will replace that number. If you find that you need to clear the telephone
numbers that are stored in memory, unplug the monitoring system control panel from the wall adapter and remove the 9V
battery for 30 seconds or more. The memory will now be erased and the reprogramming sequence can be restarted.
Programming Sequence Summary
Program 1st phone number 1. Press the “1” key for 10 seconds until green light blinks twice and then stays off.
2. Enter a maximum of 12 digits for a telephone number
3. Press the # key for 10 seconds until the green light blinks twice and then stays lit.
4. If the green light does not stay lit, repeat the programming sequence for this number
Program 2nd phone number 1. Press the “2” key for 10 seconds until green light blinks twice and then stays off.
2. Enter a maximum of 12 digits for a telephone number
3. Press the # key for 10 seconds until the green light blinks twice and then stays lit.
4. If the green light does not stay lit, repeat the programming sequence for this number
Program 3rd phone number 1. Press the “3” key for 10 seconds until green light blinks twice and then stays off.
2. Enter a maximum of 12 digits for a telephone number
3. Press the # key for 10 seconds until the green light blinks twice and then stays lit.
4. If the green light does not stay lit, repeat the programming sequence for this number
Important! Do not program emergency response phone numbers (local police or fire
departments, “911”, etc.) into the monitoring system. Do not program phone numbers to
a location where there is no one to answer the phone, or where the person answering has
not been instructed on how to respond to the alarm call.
Important! This monitoring system will not accept 9-pause outgoing numbers.
Important! This monitoring system cannot call out on an Internet phone line during a
power outage because the Internet phone system needs power to operate.
NOTE: An abbreviated Programming Sequence Summary is also located on the pullout instruction tab on the side
of the control panel housing.
Testing the Programmed Outgoing Telephone Numbers
Once you are finished programming the outgoing phone numbers, you must test the monitoring system to confirm that you
have entered the telephone numbers correctly and that the monitoring system is compatible with both your telep hone line
and the telephone(s) being called.
Testing of the first programmed outgoing telephone number:
1. Press and hold the keys “*” and “1” on the keypad until the green “system armed” light blinks 3-4 times.
2. Release the “*” and “1” keys.
3. The green light will then blink to indicate a simulated alarm condition
4. The monitoring system will make the outgoing call to the first programmed phone number.
5. You then have two verification options, with Option 1 strongly recommended.
Option 1—Answer the call yourself (such as with a cell phone) or have someone else answer the call
When the call is answered, listen to the message an d then press a nd hol d do wn the “#” k e y on t he rec ei ving te lepho ne
keypad before the message ends. Keep holding do wn the “#” key until the monitoring system sounds a 3 seco nd
continuous tone. The monitoring system will then hang up and the green “system armed” l ight on the cont rol panel will
be continuously lit indicating the monitoring system is armed.
Option 2 –Listen to the outgoing call on an extension phone
After the light blinks 3-4 times in testing step 1 above, you can pick up a phone on the same lin e not connected to the
monitoring system and listen for the successful completion of the call. Note, this will not work using the phone
connected to the monitoring system. Before the message ends, press and hold the " #" key on the phone until the
monitoring system sounds a 3 second continuous tone. The monitoring system will then hang up and the green
“system armed” light on the control panel will be continuously lit indicating the monitoring system is armed.
NOTE: If the green LED does not remain continuously lit after perfo rming the test, then press the "#" key on the
control panel until it does.
IMPORTANT - It is strongly recommended that you arrange to have someone answer the
phone being called! This is to insure that the monitoring system is compatible with your
telephone system, and to confirm correct entry of the outgoing telephone number(s).
Testing of the second and third programmed outgoing telephone numbers.
Repeat steps 1 through 5 above, substituting the “2” key on the keyp ad for the second outgoing number, and the “3” key
for the third outgoing number.
Responding to a Monitoring System Call
How the monitoring system works when it detects an alarm condition
A single or multiple alarm condition will initiat e the phone-out sequence features of this monitoring system. After a 5- or 30minute delay (depending on the switch setting selected for the “Call Dela y Time”) the monitoring system will call the first
programmed telephone number and wait up to 10 rings for the called tel ep hone to a ns wer. If the called telepho ne d oes no t
answer, or answers and no response code keys are pressed, the monitoring system will call a second a nd third telephone
number (if programmed), each time allowing 10 rings. T he monitoring system will continue the calling sequence at 15minute intervals until a called phone is answered and a r esponse code is entered, or until an alarm condition no longer
exists.
IMPORTANT - The phone connected to the monitoring system will be disco nnected when
the monitoring system is making a call in order to gain access to a dial tone and establish
a priority connection for its own use. To gain access to the phone line from this phone at
anytime the monitoring system is using it, press and hold the "#" ke y on the monitoring
system keypad until the alarm sounds a 3-second beep. If using the phone when the
alarm calls out, the phone call will be disconnected by the monitoring system. In this
case and after pressing the "#" key as described above, press the hook switch on the
telephone to receive a dial tone and redial to restore the connection.
IMPORTANT - Phones not connected to the monitoring system can gain access to the
phone line during a call made by the alarm by canceling the alarm call. To cancel an
alarm call from another extension phone and to make a call, pick up the handset, press
and hold the "#" key on the extension phone until the monitoring system sounds a beep,
and then press the hook switch on the telephone to receive a dial tone.
What to do when the monitoring system calls someone at a programmed telephone number
A voice message will advise the type of alarm condition and instruct the person answering to enter a response code by
pressing and holding the “#” key to “Acknowled ge” the alarm, or pressing the “*” key follo wed by the “0” key to “Disable”
the monitoring system. The sequence of the message is as follows:
1. A series of electronic beeps to signal a recorded message is forthcoming.
2. A recorded message is played as follows:
"Warning - Alarm condition. One beep is for temperature, two power, three accessory. A long beep is for
multiple alarms. Press # to acknowledge or press * and then 0 to disable."
3. The alarm sounds the appropriate number of distinctive beeps that define the alarm condit ion.
What happens when the call is “Acknowledged” by pressing and holding the “#” key?
4. The recorded message in 2 above repeats to make sure the alarm condition code is completely understood.
The monitoring system will sound a 3-second continuous tone at which time the "#" key can be releas ed. The monitoring
system will then disconnect and return to a monitoring mode. It will wait one hour and, if the alarm condition is still present,
will repeat the outgoing call sequence. Th is routine of calling at 1-hour intervals will continue until the alarm condition n o
longer exists OR the monitoring system is “Disabled” by pressing th e “*” key followed by the “0” key in sequence to turn the
monitoring system off (see following paragraph). Once the alarm condition no longer exists, the monitoring system will
return to the monitoring mode and will make no further calls until a new alarm condition occurs.
If a different alarm condition is detected during any of the one hour increments that the monitoring system is waiting to
make the next call, the monitoring system will then wait only 5 minutes before be ginning a new outgoing call s equence to
indicate that there are multiple alarm conditions.
What happens when the monitoring system is “Disabled” by pressing the “*” key followed by the “0” key in response to a call?
The monitoring system will sound a 3-second continuous tone at the ca lled pho ne an d the n discon nect and “D isab le” itself.
NO FURTHER MONITORING OF ALARM CONDITIONS WILL OCCUR, AND NO FURTHER OUTGOING CALLS WILL
BE MADE TO INDICATE AN ALARM CONDITION UNTIL THE MONITORING SYSTEM IS RESET AT THE CONTROL
PANEL.
What to do if you are at the monitored premises?
The monitoring system will also alert you to an alarm condition when the premises are occupied b ut when you might not
otherwise be aware, such as during the night. Upon detecting a sing le or multiple alarm condition, the control panel will
emit a 5-second continuous tone. This will be followed by a 5-second tone at 5-minute intervals thereafter.
To disable these audible warnings, move the ON / OFF switch on the monitoring s ystem control panel to the OF F position.
Turning this switch OFF will also “Disable” all features of the monitoring system, and the monitoring system will not make
any outgoing calls.
IMPORTANT – In order to have the monitoring system return to normal so that it can
monitor alarm conditions and make outgoing calls, someone will have to manually turn
the ON / OFF switch on the monitoring system control panel first to OFF and then back to
ON. This should be done at the same time you, or someone you notify, visits the
premises to correct the problem.
IMPORTANT - Be sure to turn the ON / OFF switch back to the ON position when you are
ready to begin any new alarm monitoring activity.
Troubleshooting Guide
Description of Problem Corrective Action
The red “Low Battery” light is blinking Replace battery with new 9V alkaline battery.
Monitoring system is not making an outgoing call and the green
light is on.
1. Check telephone cables.
2. Check that Pulse / Touch Tone
position for your phone system.
3. If the control panel has had the power cable
disconnected AND the battery was completely removed,
the outgoing telephone numbers will need to be
reprogrammed. Make sure the number key is pressed
down for 10 seconds before entering the number.
4. Phone number may not have been programmed properly.
Repeat programming procedure making sure the number
key is pressed down for 10 seconds before entering the
number.
5. Reset the unit by turning the on/off switch on the
monitoring system control panel first to the “OFF”
position, then “ON”.
TM
switch is in the proper
The green “System Armed” light is blinking The monitoring system is armed and an alarm condition exists.
The green “System Armed” light is off. The monitoring system either has no power, has no number in
memory or has been “disabled”. The monitoring system will not
operate when any one of these conditions exist.
1. No power. Make sure the AC adapter is plugged into both the
wall and the power jack and that a good battery is installed.
2. Disabled. Reset the unit by turning the on/off switch on the
monitoring system control panel to the “OFF” position, then
“ON”.
3. No number in memory. If the battery has discharged sufficiently
and AC power is not available, the phone numbers in the
memory will be lost. Reprogram the phone number(s).
Monitoring system can dial but cannot connect to the programmed
telephone number
You need to clear all stored telephone numbers Disconnect the control panel from the wall adapter and remove the
The monitoring system does not indicate all alarm types Make sure that the dip switch is set to the appropriate settings (see
The remote water detector does not detect the presence of water Be sure the water detector leads are properly positioned. Also be
Cannot program a number or other software related problems Remove the power cable and battery for 30 seconds. All numbers
Reprogram the outgoing telephone number to be sure you have
entered it correctly
battery for 30 seconds or more. The memory will be erased.
the section “Installation Procedure”)
sure that the length of cable between the water sensor and the
control panel does not exceed 100 feet, and is properly plugged
into the control panel
will need to be reprogrammed.
Frequently Asked Questions
Q. What happens if a called phone is answered, but no key sequence is entered?
A. The monitoring system will continue to make outgoing calls to the programmed numb er(s) until a response is entered,
or until an alarm condition no longer exists.
Q. How often should the battery be changed?
A. It depends on how much the monitoring system uses the battery for po wer. Under normal conditions when premises
power is available, the monitoring system operates solely from the AC adapter. W hen the po wer is out, the monitoring
system will use the 9-volt alkaline battery as its power source to make outgoing calls, and will expire sooner. Even a
battery that is not used at all will have to be replaced periodically. The battery should be changed when the low
battery led is lit, or before leaving the premises for extended periods of t ime. Check the low battery led after power
outages or if the AC adapter to the monitoring system has been unplugged.
Q. Can the monitoring system control panel be set on a table or floor, rather than mounting it on a
wall?
A. Yes, but care must be taken to assure that it is located where there will be adequate airflow for the temper ature sensor
to respond to temperature changes.
Q. For convenience, can the monitoring system control panel be temporarily removed from the
monitoring system base during initial programming?
A. Yes, but you should leave the AC adapter plugged in and connected to the monitoring system control panel.
Contact Information
Reliance Controls Corporation
2001 Young Court
Racine, Wisconsin 53404
www.home-protectors.com
(800) 439-5745
One Year Limited Warranty
Reliance Controls Corporation (“Reliance”) warrants this product to be free from defects in materials and workmanship
under normal use for a period of one year from date of purchase, provi ded the product has been installed and used in
accordance with Reliance’s instructions and has not bee n subjected to misuse, alteration, modification, accident, or repair
not performed by Reliance. Reliance’s obligation under this warranty is strictly limited to repair or replacement of the
product only. The cost of labor to remove the product or install a rep lacement is not included in this warranty. Reliance
shall not be liable for any incidental, special, or consequential damages whatsoever, including damage to person or
property resulting from the product’s failure to operate in the manner i n which it was designed. Use of this pr oduct is at the
risk of the owner. Reliance strongly recommends that this product be fully tested after installation in accordance with these
instructions to confirm proper operation and compatibility with your local phone system. Further, this product should be retested on a regular basis to insure continued operation. In the event that this product does not conform to this warranty
within the warranty period, the product may be returned with dat ed proof of purchase to Reliance, at the address below,
freight prepaid. Upon verification of defect Reliance shall at its sole discretion either repair or replace the defective product.
Batteries are not covered by this or any other warranty. The forgoing warranty is exclusive and in lieu of all other
expressed or implied warranties if any, including but not limi ted to implied warranties of merchantability and fitness for a
particular purpose. This warranty gives you specific legal rights, and yo u may have other rights, which vary from state to
state.
Reliance Controls Corporation
ATTN: WARRANTY CLAIMS DEPARTMENT
2001 Young Court
Racine, WI 53404
To Return a Product to Reliance Controls Corporation
Reliance will accept warranty returns for repair or replacement within the terms of the abov e warranty. All units deemed
out of warranty will be repaired at prevailing charges. All products being returned to Reliance Controls must have an RGA
number given by Reliance Controls customer service. To requ est an RGA #, call (800) 439-5745. No returns will be
accepted without an RGA number.
2001 YOUNG COURT / RACINE, WI 53404
Loading...