Reliable The IronMaven J490A Instruction Manual
The IronMaven
J490A
Home Ironing
System
with CSS
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
ENGLISH 01
FRANÇAIS 13
ESPAÑOL 25
01
THE IRONMAVEN J490A
HOME IRONING SYSTEM WITH CSS™
INSTRUCTION MANUAL
ENGLISH
02
CONGRATULATIONS
We would like to thank you, and congratulate you for purchasing
the ultimate home ironing system from Reliable Corporation.
A professional home ironing system, starting with the J490A
and using a high quality-ironing table (preferably with vacuum
and blowing functions) is the surest way of achieving professional results at home.
The excellent steam quality of this product will allow you to save
time while ironing. The powerful steam flow softens the fibres
in the fabric, allowing you to lay it down quickly and easily with
the ergonomic iron. You will wonder how you ironed without it.
For your safety and to fully enjoy the advantages of this product,
please take a few minutes to read all the important safeguards and care instructions. Keep this manual handy and
review the product warranty card for your reference.
03
IMPORTANT SAFETY INSTRUCTIONS
When using your Reliable™ home ironing system, basic safety precautions should
always be followed. Please read the following instructions carefully as they provide
important information concerning how to install, use and care for this steam iron
station.
• Use the ironing system only for its intended use.
• To protect against a risk of electric shock, do not immerse the iron or boiler in
water or any other liquids.
• The ironing system should always be turned OFF before plugging it into or
unplugging from a wall outlet. Never pull the power cord to disconnect from
the outlet; instead grasp the plug and pull to disconnect.
• Do not let the power cord to touch hot surfaces. Let the ironing system cool
completely before putting it away.
• Do not operate this product with a damaged cord, plug, or if it has been
dropped or damaged. To avoid risk of electric shock, do not disassemble
or attempt to repair the unit on your own. Return the unit to Reliable
Corporation (see warranty) for examination, repair or replacement.
• Close supervision is necessary for any appliance being used by or near
children. Do not leave the ironing system on while unattended.
• When you are using the iron, make sure it is on a firm base and not left
standing on inflammable material.
• Keep ventilation slots free from dust.
• Never drop or insert any object into ventilation slots
• To prevent overheating, unravel the electrical cord completely.
• Do not operate where aerosol (spray) products are being used or where
oxygen is being administered.
• To disconnect, turn all controls to the off position, then remove plug from the
main power.
• Never put away your steam iron while it is still hot. There is no need for emptying the tank unless you intend to leave it unused for a long period of time.
•
ATTENTION: Please make sure that before you begin ironing, you wait for the
steam ready orange light to light up. If it does not, please call contact an
authorized service depot before using.
• This product is intended for household use only – maximum 15-20 hours per
week. Follow all user instructions in this manual. Please do not leave the hot
iron on the iron rest (that sits on top of the boiler) unattended or for a period
longer than 1 hour. If the iron needs to stay on for longer than 1 hour, reduce
the temperature to the lowest setting.
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID THE WARRANTY.
04
ELECTRICAL INSTRUCTIONS
To avoid a circuit overload, do not operate another high-wattage appliance on
the same circuit simultaneously with the steam iron.
If an extension cord is necessary, a 15-amp rated cord with a polarized plug
should be used. Cords rated for less may overheat and cause damage.
POLARIZED PLUG
This steam iron system uses a polarized plug (one blade is wider than the other).
As a safety feature, this plug will fit into a polarized outlet only one way. If the plug
does not fit fully into the power outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
WATER INSTRUCTIONS
Your steam iron system has been planned for use with normal tap water. In order
to extend the life of this product, if where you are living the level of water hardness
is very high, we recommend to use 50% of normal water with 50% of demineralised or distilled water. Do not use softened water or well water.
INSTRUCTIONS TO PROGRAMME THE ANTI-CALC FEATURE
To set the de-scaling programme, you have to identify the water hardness in your
area through the water tester supplied with the ironing station.
PROCEED AS FOLLOWS:
A. Immerse the litmus paper into a water glass for one second
B. Take out the litmus paper and shake it in order to dry it
C. Wait one minute and refer to the scale here below
D. The number of red squares show the water hardness
E. The litmus paper can be used only one time
Soft water
Medium hard water
Hard water
Very hard water
For soft and medium hard water, it is okay to use regular untreated tap water, for
hard water and very hard water, it is recommended that you use a combination of
tap and distilled water.
THE DE-SCALING PROGRAMMER IS ARRANGED AS FOLLOWS:
Diagram (B)
Red LED indicates the hardness of the water.
05
PROGRAMMING INSTRUCTIONS
1. There are 4 red LED lights, each one representing a different level of water
hardness. One red LED light is for the softest water, four red LED lights is for
the hardest water.
2. To set the programme, hold the button “R” (Diagram B – #6) button down
while at the same time turning the boiler on/off switch (Diagram C – #5) on.
3. The green LED (5) will start to flash.
4. “Push” and “release” the “R” button until you have the correct number of
red LED lights lit as per the litmus paper test. Hold the “R” button down for
5 seconds until you hear an audible “beep.” Once you hear the beep, the
programme is set.
5. To verify the setting you have made, you can repeat steps #2 – #3 and you
will see the number of red LED lights lit up as per your selection (including
the flashing green light). Release the “R” button and after 15 seconds the
lights will automatically go off.
ANTI-CALC WARNING ALARM
If you hear a beeping sound from the boiler, and at the same time all the red LED
lights are flashing (after 1 minute they will stop flashing and stay on), this means
that it is time to proceed with the de-scaling of the boiler tank.
ATTENTION: It will be still possible to work for a short time while the boiler is
in the alarm mode, after which the steam station will auto-protect itself from the
scale and stop working until you de-scale the boiler.
SPECIAL NOTE
The J490A anti-calc warning system will automatically shut itself off after 57 gallons (218 litres) of water, if the programming instructions have not been followed.
It is suggested that you first clean the boiler following the cleaning instructions
outlined on page 10. Then programme the anti-calc system following the instructions above (#2 – #5) to reset the programmer.
RESET THE PROGRAMME
Once you have de-scaled the boiler (see section Maintenance of the Boiler) you
have to proceed with the RESET before starting to iron again. Repeat step #2
(in the programme instructions above and hold the “R” button down for 10 seconds.
When you hear the beap, the programme is reset.
06
TEST FIRST, THEN IRON
Prior to ironing on delicate fabrics, it is a good idea to do a test in a hidden area
(like the reverse side) to ensure that no damage is done to the fabric. We will not
assume any responsibility in case you do not comply with these instructions.
DESCRIPTION OF THE STEAM IRON SYSTEM
1. Steam regulation
2. Iron switch
3. Orange steam ready control light
4. Red water finished control light
5. Boiler switch
6. Boiler safety valve cap
7. Iron rest pad
8. Release clip
9. Cold water tank
10. Cold water tank cap
11. Electrical cable
12. Iron control light
13. Thermostat dial
14. Iron sole plate
15. Steam button
16. Continuous steam button
17. Iron handle
18. Anti-calc monitoring system
Diagram (C)
07
HOW TO USE YOUR IRONING SYSTEM
1. Unscrew the water fill cap (10).
2. Using a bottle or any other container, fill the tank (9) up to a maximum of .7
quarts of water (0.65L or 2.75 cups) or remove the tank by pushing the lever
(8) outwards while simultaneously lifting the water tank out, take it to a faucet and fill it as well to the maximum amount. Put the cap back on the boiler
when done, and place the water container back into its original position.
3. Connect the electrical cord to the main power outlet.
4. Turn on the boiler and the iron switches (2 & 5). The lights of the switches
should come on.
5. Adjust the thermostat dial on the iron (13) to the required temperature.
6. If you hear a slight hum coming from the steam generator, this means that the
pump is moving water from the water tank to the boiler where the necessary
steam is generated for ironing.
7. When using the iron for the first time, we recommend that you allow the
steam to come out (for 10-15 seconds) by pressing the steam button (15)
on the iron (without placing the iron on good fabric) in order to eliminate
any possible residue that may have been built up by treatments during the
production process.
8. You will be ready to start ironing in about 3-4 minutes, once the boiler builds
up enough pressure. The orange control light (3) will light up when you are
ready to start.
9. If the iron has not been used recently, there may be condensation in the
steam hose. Simply press the iron steam button (15) for a few seconds to
flush any condensation (water) out of the steam hose.
10. During use, the orange steam ready warning light (3) will alternately turn on
and off. This is normal because it indicates that steam is being generated
in the boiler.
11. It is safe to leave water in the pressure tank when the iron is not in use.
If it is for an extended period of time (months) then it is best to flush out the
remaining water. To do so, follow the water removal instructions as outlined
in the maintenance of the boiler section.
08
THIS MODEL IS PROVIDED WITH THE FOLLOWING FEATURES
Red control light (4)
A red warning light turns on to signal that the water in the tank has been exhaust-
ed and there will also be the sound of a buzzer in case you did not see the red
light. A continual humming of the pump comes before this. At this point you have
to switch off the ironing system by turning the power switch off, fill the tank with
water and switch back on.
Continuous steam button (16)
If you need a steady steam supply, press the continuous steam button (16) down
and the push it towards the back of the iron to lock it. To unlock it, simply reverse
this procedure.
IRONING TIPS
DRY IRONING
For ironing without steam, select the temperature (13) you require that matches
the fabric you want to iron. Turn on the iron switch (5) and the control light (12)
on the iron will light up. As soon as the light (12) goes out, the iron has reached
the right temperature. Do not press the steam button (15) when you are ironing
without steam.
ELIMINATING SHINE
If you are pressing dark coloured fabrics you may find that using an ironing shoe
made with Teflon® is beneficial to eliminating the chance of the fibres melting
and creating “shine.” An optional ironing shoe #J45T is recommended to solve
this problem.
HOW TO IRON
Everyone has their own idea on the best way to iron, and really there is no one right
way. The most important thing to remember is to set the temperature dial on the iron
(13) to the temperature that most closely matches the fabric that you are pressing.
Some people will naturally use more steam, some people less steam, some prefer
to pass over the fabric a few times, others prefer less times. Ironing in some ways
is an art, and like any art form, there are many interpretations on the “right way.”
Our best suggestion to you is to experiment, and see what works best and what
is the most comfortable for you. Ironing is a tough enough job without the iron
supplier telling you that you are doing it the wrong way. Enjoy the process, and
have fun with this amazing ironing tool.
09
FILLING THE TANK
Equipped with CSS™ (Continuous Steam System) your steam iron system can
be filled anytime during the ironing operation.
MAINTENANCE OF THE BOILER
To maintain your steam ironing system in good condition and to ensure constant
performance, we recommend that you periodically clean the boiler once or twice
a year depending on the hardness of the water:
CLEANING INSTRUCTIONS
ATTENTION: Before cleaning the boiler with the supplied de-scaling powder, please
make sure that the boiler is at room temperature, that it has not been used for at
least 8 hours, and that the boiler is disconnected from the power source.
1. Unscrew and remove the filling cap (6) that is in the middle of the ironing rest
pad (7) with the tool provided, turn the boiler over and eliminate all water
remaining in the boiler.
2. Dissolve completely the contents of the single package of de-scaling powder
in 2 cups (0.65L) of water.
3. Pour the solution into the boiler (Attention: Do not put the dissolved solution
into the water container).
4. Leave the solution in the boiler for one night with the filling cap off.
5. Completely empty the contents of the boiler and rinse three or four times
with water in order to eliminate possible residues of scale.
6. It is a good idea to spray the first steam onto a cloth and not directly on any
surface since there still may be scale in the system.
ATTENTION: IT IS NOT RECOMMENDED THAT YOU USE ANY OTHER CHEMICAL TO CLEAN
THIS PRODUCT. DOING SO WILL AUTOMATICALLY VOID THE WARRANTY.
TECHNICAL DESCRIPTION
120V Power 1750W
Cold water tank capacity 0.65L
Working pressure 4bar
Safety valve Yes
10
REPLACEMENT & OPTIONS
#J45T – Teflon® ironing shoe
#JTPOWDER Cleaning powder
TROUBLESHOOTING
Do not operate the steam cleaner with a damaged cord, plug or if the steam
cleaner has been dropped or damaged. To avoid risk of electric shock, do not
disassemble or attempt to repair the unit on your own. Return the unit to Reliable
Corporation (see warranty) for examination, repair or replacement.
PROBLEM
No steam is released through
the steam iron.
The iron soleplate remains
cold.
Water drops are leaking from
the soleplate.
Dirty steam is coming out of
iron.
Yellowing and/or melting of
the plastic.
REMEDY
1. Turn steam on/off switch
on.
2. Put required amount of
water into tank.
3 Plug unit into outlet.
4. Wait for light (3) to turn on.
1. Turn iron on/off switch on.
2. Turn the temperature dial to
the appropriate setting.
1. Increase the temperature
on the dial to the marks
between 2 and 3 dots.
2. Wait for the (3) light to
come on.
1. Clean the steam generator as per the enclosed
instructions.
2. Use demineralised/distilled water after you have
cleaned the tank (using
powder provided).
1. Do not leave the iron on
unattended.
POSSIBLE CAUSES
1. Steam on/off switch is not
turned on.
2. Water tank is empty.
3. Unit is not plugged in.
4. Generator is not fully
heated.
1. Iron is not switched on.
2. Temperature is set at minimum.
1. The soleplate temperature is too low to iron with
steam.
2. The steam generator is not
fully heated yet.
1. There may be scale in the
water tank.
2. Not using the right type of
water for your boiler.
1. Leaving the iron on the iron
rest at high temperature.
Loading...