GB
P1-MP2-RD
Operating Manual
7
1
Weld seam
2
Zip fastening
3
Clip
4
Print head
5
Clip arms
6
Print head nozzles
7
Print head contacts
A
D
B
C
E
1
234
5
6
733
4
5
7
8
GB
For your safety
DANGER
Warnings about risks where non-observance
of the measures may directly cause death or
serious injury.
WARNING
Warnings about risks where non-observance
of the measures may cause death or serious
injury.
CAUTION
Warnings about risks where non-observance of
the measures may cause injury.
PLEASE NOTE
Warnings about risks where non-observance of
the measures may cause material damage.
Instructions and tips
Safety instructions for MP ink
WARNING
Special ink is highly flammable. Risk of burns!
„ Store at 10 °C - 20 °C.
„ Do not expose to direct sunlight.
WARNING
If in eyes.
„ Rinse cautiously with water for several minutes.
„ Remove contact lenses, if present and easy to do.
„ Continue rinsing. Immediately call a POISON CENTER
or doctor/physician.
9
1. Making the print head ready for use
1.1. Opening the pack _ Fig.
A
The aluminium pouch has a resealable zip fastening
2
.
„ With scissors, cut open the top of the pack between
the weld seam
1
and the zip fastening
2
.
„ Unzip
2
the pack.
„ Take out the print head
4
.
1.2. Releasing the clip _ Fig.B +
C
The print head
4
is supplied with a reusable clip
3
.
„ Place the print head
4
on a firm surface at an angle
of about 45° as shown in figure
C
.
„ Hold the red clip
3
by the point with one hand.
„ With the other hand, press the print head
4
down firmly. The
clip arms
5
will spring out and the print head
4
will slide
away from the clip
3
.
2. Printing material
For the best results, use material that is clean, non-greasy, dry
and at the same temperature as the print head.
Before carrying out a large print job, perform a test print.
10
GB
3. Storage _ Fig.A +
D
MP ink is fast-drying. The time it takes the print head
nozzles
6
to dry up depends on the ambient temperature
and the humidity.
- If the printing break will probably take more than 5 minutes,
the print head
4
should be protected with the clip
3
.
- If the printing break will probably take more than 2 hours,
the print head
4
with the clip
3
should be stored in the
air-tight aluminium pouch.
„ Remove the print head
4
out of the device.
„ Place the print head
4
with the clip
3
on a smooth and solid
surface as shown in figureD .
„ Press the print head
4
down until it snaps in the clip
3
.
„ Place the print head
4
into the aluminium pouch and close
the zip fastening completely.
Use the print head within four weeks after opening.
11
4. Environmental Conditions
Temperature for storage 10°C to +20°C
Temperature for transport -20 °C to +40 °C (up to 24 hours)
5. Troubleshooting
Dried ink on the print head nozzles
6
may result in streaks
or reduced print quality.
5.1. Automatic cleaning
„ Read the information about the cleaning of the print head
nozzles
6
in the manual for the electronic stamp.
5.2. Cleaning the print head nozzles manually
If the automatic cleaning of the nozzles
6
does not produce the
desired result, we recommend proceeding as follows:
„ To remove dried ink, press a soft cloth, if necessary lightly
soaked in ethanol (spirits), against the print head nozzles
6
for about 3 seconds.
„ Dab off the dissolved ink and wipe the nozzles dry.
12
GB
5.3. Reactivating the print head
If ink has dried inside the print head
4
it may be necessary
to reactivate it.
„ Lay the print head down on a firm surface protected by
a lint-free cloth or piece of material.
„ Place the syringe supplied firmly against the opening on top
of the print head
4
and carefully inject a small amount of air
(approx. 0.5 ml).
PLEASE NOTE
Risk of staining from discharged ink.
„ Wipe up discharged ink with a lint-free cloth or piece of
material.
5.4. Cleaning the print head contacts
In rare cases, dirt on the print head contacts
7
may result in
inferior printing results.
„ Clean the contacts on the print head
4
and in the device with
a soft cloth or cotton bud, if necessary lightly soaked
in ethanol (spirits).
Disposal
Directive 2002/96/EC (WEEE)
Electrical and electronic equipment and batteries
should not be disposed of along with domestic
or general waste. Dispose of equipment in an
environmentally friendly way.
37
Notes
Ernst Reiner GmbH & Co. KG
Baumannstr. 16
78120 Furtwangen
Phone +49(0)7723 657-0
Fax +49(0)7723 657-200
reiner@reiner.de
www.reiner.de
Award for
Operational
Excellence
|ZN-791061-001 F|02-2014
Danger
REINER MP2 RD
4 ml
Flammable liquid and vapour.
Causes serious eye damage.
H318H226
Acid Red 52Ethanol
Loading...