Regency P33-LP3, P33-NG3 User Manual

Download

www.regency-ﬁ re.com

P33-3 Zero Clearance

Direct Vent Gas Fireplace

Owners &

Installation Manual

MODELS: P33-NG3 Natural Gas P33-LP3 Propane

WARNING: If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

FOR YOUR SAFETY Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualiﬁ ed installer, service agency or the gas supplier.

Tested by:

918-262a

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

FOR YOUR SAFETY What to do if you smell gas:

Do not try to light any appliance Do not touch any electrical switch:

do not use any phone in your building.

Immediately call your gas supplier

from a neighbour's phone. Follow the gas supplier's instructions.

If you cannot reach your gas

supplier, call the ﬁ re department.

01/04/06

To the New Owner:

Congratulations!

You are the owner of a state-of-the-art Gas Stove by FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. The

P33-3 has been designed to provide you with all the warmth and charm of a wood ﬁ replace at the ﬂ ick of a switch.

The P33-3 has been approved by Warnock Hersey for both safety and efﬁ ciency. As it also bears our own mark,

it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a

moment now to acquaint yourself with these instructions and the many features of your Regency Fireplace.

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2002/CSA 2.33-2002 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN/CGA-2.17-M91.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

Ensure that structural members are not cut or weakened during installation.

This Regency Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit.

This Regency Mobile/Manufactured Home listed appliance comes equipped with a dedicated #8 ground lug to which an 18 gauge copper wire from the steel chassis ground must be attached.

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

TABLE OF CONTENTS

P33-3 ZERO CLEARANCE

DIRECT VENT GAS FIREPLACE

Page Page

Safety Label

Safety Label ............................................................... 4

Installation

Important Message ..................................................... 5

Before You Start ......................................................... 5

General Safety Information ........................................ 5

Manufactured Home Additional Requirements ........... 5

Installation Checklist ................................................... 6

Unit Dimensions ......................................................... 6

HeatWave Duct System Option .................................. 6

Locating Your Gas Stove ............................................ 6

Clearances ................................................................. 7

Combustible Mantel Clearances ................................ 7

Mantel Leg Clearances .............................................. 7

Framing and Finishing ................................................ 8

Unit Assembly Prior to Installation .............................. 9

Venting Introduction .................................................... 9

Exterior Vent Termination Locations ......................... 10

Venting - Regency Direct Vent System (Flex)

Horizontal Terminations only .....................................11

Venting - Installation of Regency Direct Vent

System (Flex) ..................................................... 12

Venting - Rigid Pipe Venting Systems ...................... 13

Rigid Pipe Venting Components List ........................ 14

Venting Arrangements - Vertical Terminations .......... 15

Venting Arrangements - Horizontal Terminations .... 17

Vertical Terminations - Co-Linear Flex System ......... 21

Venting Arrangements .............................................. 22

Venting - Horizontal Installations .............................. 23

Venting - Vertical Termination ................................... 24

Gas Line Installation ................................................. 24

Pilot Adjustment ........................................................ 25

High Elevation .......................................................... 25

System Data ............................................................. 25

Gas Pipe Pressure Test ............................................ 25

SIT Valve Description ............................................... 25

Conversion to Propane ............................................. 26

Optional Brick Panels ............................................... 27

Log Installation ......................................................... 27

Flush Door - Standard .............................................. 28

Flush Trim (optional) ................................................. 28

Louvers - Flush ........................................................ 29

Double Screen Door ................................................. 29

Bay Front (optional) .................................................. 29

Bay Trim (optional) ................................................... 29

Louvers - Bay ........................................................... 30

Full Screen Front ...................................................... 31

Remote Control (optional) ........................................ 33

Wall Thermostat (optional) ....................................... 33

Remote Wall Switch (optional) ................................. 33

Wiring Diagram ......................................................... 34

Fan Installation (optional) ......................................... 35

Operating Instructions

Lighting Plate Instructions ........................................ 36

Operating Instructions .............................................. 37

Lighting Procedure ................................................... 37

Shutdown Procedure ................................................ 37

First Fire ................................................................... 37

Aeration Adjustment ................................................. 37

Normal Operating Sounds of

Gas Appliances .................................................. 38

Maintenance

Maintenance Instructions ........................................ 38

General Vent Maintenance ....................................... 38

Gold-Plated or Brass Louvers .................................. 38

Gold Plated or Brass Trim ........................................ 38

Log Replacement ..................................................... 38

Thermopile/Thermocouple ....................................... 39

Glass Gasket ............................................................ 39

Door Glass: Flush and Bay Glass ............................ 39

Removing Valve ........................................................ 40

Installing Valve .......................................................... 40

Parts List

Replacement/Spare Parts List .................................. 41

Warranty

Warranty ................................................................... 47

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

SAFETY LABEL

This is a copy of the label that accompanies each P33-3 Zero Clearance Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. The safety label is located on the front inside base of the unit, visible when the bottom louver is open.

NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

For the State of Massachusetts, installation and repair must be done by a plumber or gasﬁ tter licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, ﬂ exible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

IMPORTANT:

SAVE THESE

INSTRUCTIONS

The P33-NG3 or P33-LP3 Direct Vent Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual ﬁ rst. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the responsibility of the installer to ensure this ﬁ replace is installed in compliance with manufacturer's instructions and all applicable codes.

BEFORE YOU START

Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the

INSTALLATION AND REPAIR SHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.

GENERAL SAFETY

INFORMATION

1) The appliance installation must conform with

local codes or, in the absence of local codes, with the current Canadian or National Gas Codes, CAN1-B149 or ANSI Z223.1 Installation Codes.

2) The appliance when installed, must be

electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.

3) See general construction and assembly

instructions. The appliance and vent should be enclosed.

4) This appliance must be connected to the

speciﬁ ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is ﬁ tted as per Venting instructions.

5) Inspect the venting system annually for

blockage and any signs of deterioration.

6) Venting terminals shall not be recessed into a

wall or siding.

10) Be aware of electrical wiring locations in

walls and ceilings when cutting holes for termination.

11) Under no circumstances should this ap-

pliance be modiﬁ ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

12) Installation and any repairs to this appliance

should be done by a qualiﬁ ed service person. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

13) Do not slam shut or strike the glass door.

14) Under no circumstances should any solid

fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.

15) The appliance area must be kept clear and

free of combustible materials, (gases and other ﬂ ammable vapours and liquids).

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1) Ensure that structural members are not cut

or weakened during installation.

2) Ensure proper grounding using the #8

ground lug provided. See page 34.

WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY

7) Any safety glass removed for servicing

must be replaced prior to operating the appliance.

AND MAY CAUSE A SERIOUS HOUSE FIRE.

CHILDREN AND ADULTS SHOULD

8) To prevent injury, do not allow anyone who

is unfamiliar with the operation to use the ﬁ replace.

BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIRE-

9) Wear gloves and safety glasses for protec-

tion while doing required maintenance.

PLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

CHECKLIST

1) Locate appliance

a) Room location, page 6 b) Clearances to Combustibles, page 7 c) Mantle Clearances, page 7 d) Framing & Finishing Requirements, page 8 e) Venting Requirements, pages 10 to

15.

2) Assemble Top Facing Support and Side

Nailing Strips, page 9. (NOTE: must be done before installing unit into ﬁ replace.)

3) Install vent, pages 10 to 24.

4) Make gas and electrical connections. Test

the pilot. Must be as per diagram. Page 25. Convert to Propane if desired, page 26.

5) Install brick panels (optional), page 27.

6) Install logs and embers and rockwool where

indicated on page 27.

7) Install Flush Door Front (Standard) and

optional Flush Gold Trim, page 28.

UNIT DIMENSIONS

4) The P33-3 can be installed in a recessed

position or framed out into the room as in A, B, C, D. See Diagram 1.

5) This appliance is Listed for bedroom instal-

lations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.

6) The P33-3 Direct Vent Gas Fireplace is ap-

proved for alcove installations, which meet the clearances listed on this page.

7) We recommend that you plan your instal-

lation on paper using exact measurements for clearances and ﬂ oor protection before actually installing this appliance. Have a qualiﬁ ed inspector, dealer, or installer review your plans before installation.

Note: For vent terminations see page 10.

8) Install optional Double Screen Door, page

29.

9) Install Optional Bay Front and optional Bay

Gold Trim, page 29.

10) Install Louvers (Flush or Bay), pages 28

and 29.

11) Install optional Wall Switch, Remote Control,

or Wall Thermostat, page 33.

11) Install Optional Fan, page 35.

13) Final check.

Before leaving this unit with the customer, the installer must ensure that the appliance is ﬁ ring correctly and operation fully explained

to customer.

This includes:

1) Clocking the appliance to ensure the correct

ﬁ ring rate (rate noted on label) after burning appliance for 15 minutes.

2) If required, adjusting the primary air to ensure

that the ﬂ ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

LOCATING YOUR

GAS STOVE

1) When selecting a location for your stove,

ensure that the clearances outlined on this page are met.

2) Provide adequate clearances for servic-

ing.

3) The appliance must be installed on a ﬂ at,

solid, continuous surface (e.g. wood, metal, concrete). This may be the ﬂ oor, or raised up on a platform to enhance its visual impact. If the appliance is going to be installed on carpeting, combustible linoleum tile or other combustible material other than wood ﬂ ooring, the appliance must be installed on a metal or wood panel extending the full width and depth of the appliance.

Diagram 1

A) Flat on Wall B) Flat on Wall Corner C) Recessed into Wall/Alcove

DUCT SYSTEM

OPTION

KIT #946-556

The HeatWave Air Duct Kit increases the effectiveness of your ﬁ replace by dispersing warm air from the ﬁ replace to remote locations in the same room or other rooms in your home.

Up to two kits may be installed on the ﬁ replace. Please Note: Only 1 HeatWave kit may be operated at one time. This includes the internal blower option as well.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

CLEARANCES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related ﬁ res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this ﬁ replace and vent system be installed only in accordance with these instructions.

Clearance to Combustibles from: Back 0" (0mm) Side 0" (0mm) Floor 0" (0mm)

NOTE: The minimum ﬂ oor clearance must be maintained from the top surface of the carpeting, tile, etc.

Minimum Clearance from Top of Unit to:

Mantel* min. 7" (177mm) Ceiling 30" (762mm)

from top of unit.

Side Wall Clearance

Bay or Flush Front 7-1/2" (191mm)

Minimum Vent Clearances:

2-1/2" (64mm) Horizontal Top 1-1/2" (38mm) Horizontal Side 1-1/2" (38mm) Horizontal Bottom 1-1/4" (32mm) Vertical Vent Clearance (Simpson) 1-1/2" (38mm) Vertical Vent Clearance (Flex)

Alcove Clearances: Max. Depth 36" (914mm) Min. Width 48" (1219mm) Min. Height 59" (1499mm)

* see mantel clearance instructions.

WARNING Fire hazard is an extreme risk if these clearances are not adhered to.

Because of the extreme heat this ﬁ replace emits, the mantel clearances are critical. Com-

bustible mantel clearances from top of unit are shown in the diagram below.

Note: A non-combustible mantel may be installed at a lower height if the framing is made

of metal studs covered with a non-combustible board.

This drawing is to scale at 1:6 (one inch = 6 inches). Mantel can be installed anywhere in shaded area or higher using the above scale.

Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the

COMBUSTIBLE MANTELS

paint may discolour.

MANTEL LEG CLEARANCES

Combustible mantel leg clearances as per diagram below:

Clearances for Bay or Flush Front

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Maximum 1-1/2" projection at 2" minimum clearance.

The HeatWave Duct Kit has different clear- ance and framing requirements, check the HeatWave manual for details.

INSTALLATION

FRAMING AND FINISHING

1) Determine the total thickness of facing

material (e.g. drywall plus ceramic tiles) to allow the ﬁ nished surface to be ﬂ ush with the front of the unit. Total facing thickness can vary from 1/2" (13mm) to 1-1/4" (32mm) thick.

Install Side Nailing Strips, and Top Facing Support before unit is slipped into position. See page 9 for assembly details.

2) Frame in the enclosure for the unit with

framing material.

Vertical Termination or

Vertical Rise with Horizontal

Termination

For Both Simpson & Flex

NOTE: If this is an outside corner, the

minimum distance between the vent and the outside corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Dura-Vent termination cap.

Rear Termination

Simpson Dura-Vent Piping

Flex Piping

For Both Simpson & Flex

NOTE: If this is an outside corner, the minimum

distance between the vent and the outside corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Dura-Vent termination cap.

3) For exterior walls, insulate the enclosure to

the same degree as the rest of the house, apply vapour barrier and drywall, as per local installation codes. (Do not insulate the

ﬁ replace itself.)

4) The top of the unit must not be closer than

30" (762mm) to the ceiling.

5) Combustible material may be brought up to

the top and sides of the unit and be covered with ceramic tiles, bricks, rock or other suitable combustible ﬁ nishing materials.

Note: The unit does not have to be complete-

ly enclosed in a chase. The clearance on top of the unit is 0" to the standoffs so combustible building materials can be laid directly on top of the standoffs. You must maintain clearance from the vent to combustible materials for ﬂ ex for Simpson Dura-Vent, see page 7.

Simpson Dura-Vent

Minimum Clearances

Top Header

1/2" (13mm) Drywall

1-1/2"

(38mm)

(102mm)

Opening for gas

(76mm)

connection

10" (254mm)

dia. Hole through

wall for Dura-Vent

30”

(762mm)

16-1/2” (419mm) Minimum

Flex Pipe

Minimum Clearances

Top Header

1/2" (13mm) Drywall

1-1/2"

(38mm)

(102mm)

Opening for gas

6) Use steel studs for framing where the 1-1/2" (38mm) clearance from the vent

to combustible material cannot be maintained.

The HeatWave Duct Kit has different clear- ance and framing requirements, check the HeatWave manual for details.

(76mm)

connection

10" (254mm)

dia. Hole through

wall for Flex

26”

(660mm)

12-3/4” (324mm) Minimum

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

UNIT ASSEMBLY

PRIOR TO INSTALLATION

INSTALLATION

The Top Facing Support, the Side Nailing Strips and the 2 Top Standoffs must be correctly positioned and attached to the top before the unit is put into position.

Top Standoff Assembly

The top standoffs are shipped in a ﬂ at position and must be pulled up and bent into the correct shape.

1) Remove the standoffs from on top of the

ﬁ rebox by undoing the screws.

2) Take each standoff and bend into the cor-

rect shape. Bend up at the bend lines until the screw holes in the standoff and the pre-punched screw holes on the ﬁ rebox top line-up.

3) Attach the standoffs securely to the top with

4 screws per standoff.

Note: Secure the standoffs to the holes

closest to the edge of the ﬁ rebox top.

Top Facing Support &

Side Nailing Strips

Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the ﬁ nished surface to be ﬂ ush with the front of the unit. Total facing thickness can vary from 1/2" (13mm) to 1-1/4" (32mm) thick.

The Top Facing Support & Side Nailing Strips can be mounted in various positions depending on the thickness of the facing material.

1) Mount Top Facing Support using the 3

supplied screws into the three pre-punched screw holes on the top front of the unit. Adjust support to desired facing material depth.

2) Mount Side Nailing Strip using the 3 sup-

plied screws into the three pre-punched screw holes at the front sides of the unit. Adjust support to desired facing material thickness.

For a facing material depth of 1-1/4"(32mm), the top facing support must be reversed.

VENTING INTRODUCTION

The P33-3 uses the "balanced ﬂ ue" technology Co Axial system. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

There are 2 vent systems approved for use with the P33-3: the Regency Direct Vent System (Flex) for Horizontal Terminations only (see pages 11-12), and the Simpson Dura-Vent Systems for Horizontal and Vertical Terminations (see pages 13-24).

Note: These ﬂ ue pipes must not be connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

EXTERIOR VENT TERMINATION LOCATIONS

18"

24"

Vertical

Termination

Closed

Fixed

Openable

Area where terminal is not permited

from the centerline of the regulator.

any other appliance *(12"/30cm) #(9"/23cm)

H= Not to be installed above a meter/regulator assembly within (3'/90cm) horizontally

J= Clearance to service regulator vent outlet *(min. 36"/90cm)

K= Clearance to non-mechanical air supply inlet to building or the combustion air inlet to

*(min. 84"/2.1m)

L= Clearance to a mechanical air supply inlet *(min. 72"/1.8m)

#3' (91cm) above if within 10' (3m) horizontally.

M= Clearance above paved sidewalk or a paved driveway located on public property

N= Clearance under veranda, porch, deck, or balcony *(min. 12"/30cm)

Inside

corner detail

Vertical

Termination

Air supply outlet

Openable

Fixed

Closed

24"

Vent terminal

Dura-Vent Termination Cap (12"/30cm)

distance of (24"/60cm) from the centerline of the terminal (min. 18"/46cm) check with

local code.

A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm)

B= Clearance to window or door that may be opened *(12"/30cm) #(9"/23cm)

C= Clearance to permanently closed window *(min. 12"/30cm)

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

E= Clearance to unventilated sofﬁ t (min. 15"/38cm)

D= Vertical clearance to ventilated sofﬁ t located above the terminal within a horizontal

Vent Termination Cap (12"/30cm)

G= Clearance to inside corner: with AstroCap Termination Cap (min. 6"/15cm), with Dura-

F= Clearance to outside corner: with AstroCap Termination Cap (min. 6"/15cm), with

Note:

- A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

- Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the ﬂ oor.

- If the vent termination is accessible, a certiﬁ ed guard shall be installed.

* As speciﬁ ed in CGA B149 Installation Code. Note: Local codes or regulations may require different clearances.

# In accordance with the current ANSI Z223.1/NFPA 54, Natioinal Fuel Gas Code.

INSTALLATION

REGENCY DIRECT VENT SYSTEM (FLEX)

HORIZONTAL TERMINATIONS ONLY

This venting system, in combination with the P33-3 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram on page 10.

Regency Direct Vent (Flex) System Termination Kit (Part # 946-513) includes all the parts needed to install the P33-3 with a maximum run of 2 feet. If installing the P33 with a continuous vent length of more than 2 ft (.6m) to a maximum of 10 ft. (3.0m) using Kit # 946-515 (4 ft) or

946-516 (10 ft) or see page 13 for alternate venting arrangements.

1) 6-7/8" dia. ﬂ exible liner (2 ft. length)

2) 4" dia. ﬂ exible liner (2 ft. length)

3) spring spacers (3)

4) thimble (2)

5) AstroCap termination cap (1)

6) screws (12)

7) tube of Mill Pac (1)

8) plated screws (8)

9) screws #8 x 1-1/2" drill point, stainless steel (4)

Notes:

1) Liner sections should be continuous without any joints or seams.

2) Only Flex pipe purchased from Regency may be used for Flex installations.

4" (102mm)

dia. flue pipe

Wall Thimble (2 pc)

(required in

Canada only)

spring spacer

AstroCap

Termination Cap

(Part# 946-523/P)

See also

Figure 1 below.

Important

If using any Cabinet Mantels with Part # 510956, 510958, 510962, 510964 and 510834 the wall thimble must be secured ﬁ rst and venting must be attached to unit before sliding into ﬁ nal position.

Also Simpson Dura-Vent venting cannot be used with any of the mantels

noted above.

Minimum

Simpson Dura-Vent Center-Line

6-7/8"

(173mm)

dia. Flue pipe

Minimum Flex Kit Center-Line

Alternate Hori-

zontal Termi-

nation Caps

Figure 1

Wherever necessary due to external location of cap, the AstroCap can be replaced with the FPI Riser Vent Termination Cap or the Dura-Vent Snorkel Termination Cap.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

INSTALLATION PROCEDURES

for Regency Direct Vent System (Flex)

1) Locate the unit in the framing, rough in the

gas (preferably on the right side of the unit) and the electrical (Junction block is on the left side) on the left. Locate the centerline of the termination and mark wall accordingly. Cut a 10"(254mm) hole in the wall (inside dimension).

Note: To make the installation more aes-

thetically pleasing, we recommend framing out a square to mount the terminal to.

Note: A 2-1/2" (64mm) horizontal top and

1-1/2" (38mm) horizontal sides & bottom clearance around the liner must be maintained except that only a 1" (25mm) clearance is needed at the termination end. We recommend framing a 10"(254mm) x 10"(254mm) (inside dimensions) hole to give structural rigidity for mounting the termination.

Note: If installing termination on a siding

covered wall, furring strips must be used to ensure that the termination is not recessed into the siding.

2) Level the ﬁ replace and fasten it to the fram-

ing using nails or screws through the nailing strips.

3) Assemble the vent assembly by applying

Mill Pac to the 4"(100mm) inner collar of the termination and slipping the 4"(100mm) liner over it at least 1-3/8" (35mm). Fasten with the 3 screws (drilling pilot holes will make this easier). Apply Mill Pac or high temperature silicone to the 6-7/8"(175mm) ﬂ ex pipe and slip it over the 6-7/8" outer collar of the vent terminal at least 1-3/8"(35mm) and fasten with the 3 screws.

4) Separate the 2 halves of the wall thimble and

securely fasten the one with the tabs to the outside wall making sure that the tabs are on top and bottom. Fasten the other thimble half to the inside wall. The thimble halves slip inside each other and can be adjusted for 2 x 4 or 2 x 6 walls. The liners must slip

over the collars a minimum of 1-3/8".

*If this is an outside corner, the minimum distance between the vent and the outside corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Dura-Vent termination cap. See "F" on the diagram on page 10.

Minimum and Maximum Vent Clearances

5) Slip the assembled liner and termination

assembly through the thimble making sure the termination cap faces up (there are markings on the cap that show which way is up). This will position the termination cap with proper down slope for draining water. Fasten the cap to the outer wall with the 4 supplied screws.

6) Pull the centre 4"(100mm) liner and outer

6-7/8"(175mm) liner out enough to slip over the ﬂ ue collars of the ﬁ replace.

7) Apply Mill Pac over the ﬁ replace inner collar

and slip the 4"(100mm) liner down over it and attach with 3 supplied screws.

8) Do the same with the 6-7/8"(175mm) liner.

4" (102mm)

dia. flue pipe

with spring spacer

Screws

(3 per

connection)

6-7/8"

(175mm)

dia. air intake

Wall Thimble 2 pieces

(10" (254mm) Outer Diameter)

9) Apply a bead of silicone between the thimble

and termination and around the outer edge of the terminal at the wall in order to keep the water out.

IMPORTANT: Do not locate termination hood where excessive snow or ice buildup may occur. Be sure to check vent termination area after snow falls, and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination

area.

2”x4”or2”x6”

(21mm x 102mm

or 21mm x 152mm)

Termination Cap

Screws

(4 per connection)

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

RIGID PIPE VENTING SYSTEMS

Horizontal or Vertical Terminations

INSTALLATION

The minimum components required for a basic horizontal termination are:

1 AstroCap Horizontal Termination Cap 1 45o Elbow 1 Rigid Pipe Adaptor 1 Wall Thimble 1 Length of pipe to suit wall thickness (see chart)

For siding other than vinyl furring strips may be used, instead of the vinyl siding standoff, to create a level surface to mount the vent terminal. The Terminal must not be recessed into siding.

If a Vinyl Siding Standoff is required (it must be used with vinyl siding), measure to outside surface of wall without siding and add 2 inches.

Alternate Hori-

zontal Termi-

nation Caps

Vertical

Terminal

Storm Collar

Flashing

Ceiling Firestop

Pipe Length

90 Elbow

24" (610mm)

Pipe Length

45 Elbow

Vinyl Siding

Standoff (Optional)

Adj.Pipe Length

11" - 14-5/8"

(279mm - 372mm)

Wall Thimble

Adj.Pipe Length

11" - 14-5/8"

(279mm - 372mm)

Horizontal

Termination

Cap

Wall Thimble

Horizontal

Termination Cap

Vinyl Siding

Standoff (Optional)

Rigid Pipe Adaptor

WARNING:

Do not combine venting components from different venting systems.

However use of the the AstroCapTM and FPI Riser is acceptable with all systems.

This product has been evaluated by Intertek for using a Dura-Vent Flue Adaptor in conjunction

Flat Wall Installation

Max. Wall Vent Length

Thickness (inches) Required (inches)

7-1/4" 6"

with Selkirk Direct-Temp and Ameri Vent Direct venting systems. Use of these systems with the Direct Vent GS starting collar is deemed acceptable and does not affect the Intertek WHI listing of components.

10-1/4" 9" 13-1/4" 12" 12-1/4" - 15-7/8" 11" - 14-5/8" Adj. Pipe 18-1/4" - 25-1/4" 11" - 14-5/8" Adj. Pipe

The FPI AstroCap American Metal Products, Ameri Vent Direct vent and Selkirk Direct-Temp. FPITM, and FPI AstroCapTM are the proprietary trademarks of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

and FPI Riser Vent terminal is certiﬁ ed for installations using FPI venting systems as well as Simpson Dura-Vent®, Direct Vent GS,

When using piping other than Simpson

Dura-Vent, 3 screws must be used to

secure rigid pipe to adaptor.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

RIGID PIPE VENTING COMPONENTS LIST

All Simpson Dura-Vent components are available directly from FPI.

Description Simpson Dura-Vent Selkirk AmeriventR Direct VentGS

6" Pipe Length, Galvanized 908 4DT-6 N/A 6" Pipe Length, Black 908B 4DT-6B N/A 7" Pipe Length, Galvanized N/A N/A 4D7 7" Pipe Length, Black N/A N/A 4D7B 9" Pipe Length, Galvanized 907 4DT-9 N/A 9" Pipe Length, Black 907B 4DT-9B N/A 12" Pipe Length, Galvanized 906 4DT-12 4D12 12" Pipe Length, Black 906B 4DT-12B 4D12B 18" Pipe Length, Galvanized N/A 4DT-18 N/A 18" Pipe Length, Black N/A 4DT-18B N/A 24" Pipe Length, Galvanized 904 4DT-24 4D2 24" Pipe Length, Black 904B 4DT-24B 4D2B 36" Pipe Length, Galvanized 903 4DT-36 4D3 36" Pipe Length, Black 903B 4DT-36B 4D3B 48" Pipe Length, Galvanized 902 4DT-48 4D4 48" Pipe Length, Black 902B 4DT-48B 4D4B

Adjustable Length, 11"-14", Galv. 911 4DT-AJ N/A Adjustable Length, 11"-14", Black 911B 4DT-AJB N/A Adjustable Length, 17"-24", Black 917B N/A N/A Adjustable Length, 7" Galvinized N/A N/A 4D7A Adjustable Length, 7" Black N/A N/A 4D7AB Adjustable Length, 12" Galvinized N/A N/A 4D12A Adjustable Length, 12" Black N/A N/A 4D12AB

45O Elbow, Galvinized 945 4DT-EL45 4D45L

Elbow, Black 945B 4DT-EL45B 4D45LB

Elbow, Swivel, Galvinized 945G N/A N/A

Elbow, Swivel, Black 945BG N/A N/A

45 90O Elbow, Galvinized 990 4DT-EL90S 4D90LS

Elbow, Black 990B 4DT-EL90SB 4D90LBS

Elbow, Swivel, Galvinized 990G N/A N/A

90 90O Elbow, Swivel, Black 990BG N/A N/A

Ceiling Support 949 - n/a from FPI 4DT-CS 4DFSP Cathedral Support Box 941 4DT-CSS 4DRSB Wall Support/Band 988 4DT-WS/B 4DWS Offset Support 989 - n/a from FPI 4DT-OS N/A Wall Thimble, Black 942 4DT-WT 4DWT Wall Thimble Support Box/Ceiling Support 940 N/A N/A Firestop Spacer 963 4DT-FS 4DFSP Trim Plate, Black N/A 4DT-TP 4DFPB Brass Trim for Wall Thimble/Ceiling Support 3951 N/A N/A

Attic Insulation Shield 12" N/A N/A 4DAIS12 Attic Insulation Shield - Cold Climates 36" N/A N/A 4DAIS36

Basic Horizontal Termination Kit (A) 970 4DT-HKA 4DHTK2 Horizontal Termination Kit (B) 971 4DT-HKB 4DHTK1 Vertical Termination Kit 978 4DT-VKC 4DVTK

High Wind Vertical Cap 991 N/A N/A High Wind Horizontal Cap 985 N/A N/A Horizontal Square Termination Cap 984 4DT-HHC 4DHC Verical Termination Cap 980 4DT-HVC 4DVC Storm Collar 953 4DT-SC 4DSC

Adjustable Flashing, 0/12-6/12 943 4DT-AF6 4DF Adjustable Flashing, 6/12-12/12 943S 4DT-AF12 4DF12

Vinyl Siding Standoff 950 4DT-VS N/A Vinyl Siding Shield Plate N/A 4DT-VSP N/A

Snorkel Termination 14" 982 4DT-ST14 4D12S Snorkel Termination 36" 981 4DT-ST36 4D36S

Direct-Temp

Direct Vent

946-506/P Vent Guard (Optional) 640-530/P Riser Vent Terminal 510-994 Rigid Pipe Adaptor (must use with all rigid piping) 946-205 Vinyl Siding Shield for Riser Vent Terminal

946-208/P Vent Guard (Optional) - Riser Vent Terminal 946-523/P AstroCap Horizontal Cap 946-206 Vinyl Siding Standoff - AstroCap

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS

(Propane & Natural Gas)

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations , using one 90o elbow, with

rigid pipe vent systems for Propane and Natural Gas.

• Vent must be supported at offsets.

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

• Maintain clearances to combustibles.

Note: Must use optional rigid pipe adapter when using rigid pipevent systems (Part # 510-994).

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

The P33-3 is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural Gas.

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations with rigid pipe vent systems for Propane and Natural Gas. Maximum two 45

• Vent must be supported at offsets.

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

• Maintain clearances to combustibles.

elbows allowed.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS

REGENCY DIRECT VENT SYSTEM (FLEX)

(Propane & Natural Gas)

This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal

one 90

elbow).

Note: Must use optional rigid pipe adaptor (Part # 510-994) when using rigid pipe vent systems. (Refer to page 13.)

Minimum

Simpson Dura-Vent Center-Line

A vent guard should be used whenever the termination is lower than the speciﬁ ed minimum or as per local codes.

Note: Regency Direct Vent System (Flex) is

only approved for horizontal terminations.

• Maintain clearances to combustibles.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

Minimum Flex Kit Center-Line

Important

If using any Cabinet Mantels with Part # 510956, 510958, 510962, 510964 and 510834 the wall thimble must be secured ﬁ rst and venting must be attached to unit before sliding into ﬁ nal position.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Also Simpson Dura-Vent venting cannot be used with any of the mantels

noted above.

INSTALLATION

Horizontal Venting with Two (2) 90o Elbows

One 90o elbow = Two 45o elbows.

Option V H + H1

A) 1' Min. 3' Max. B) 2' Min. 4' Max. C) 3' Min. 5' Max. D) 4' Min. 6' Max. E) 5' Min. 7' Max. F) 6' Min. 8' Max.

With these options, maximum total pipe length is 30 feet with minimum of 6 feet total vertical and maximum 8 feet total horizontal.

Please note minimum 1 foot between 90o elbows is required.

Horizontal Venting with Three (3) 90

elbow = Two 45o elbows.

One 90

Option H V H + H1 + H2 A) 1 Max. 1' Min. 3' Max.

B) 2' Max. 3' Min. 5' Max. C) 3' Max. 5' Min. 6' Max. D) 4' Max. 7' Min. 7' Max. E) 5' Max. 9' Min. 8' Max. F) 6' Max. 11' Min. 9' Max.

Elbows

With these options, max. total pipe length is 30 feet with min. of 11 feet total vertical and max. 9 feet total horizontal.

Please note min. 1 foot between 90 elbows is required.

One 90

elbow = Two 45o elbows.

Option H V H + H1

A) 1' Max. 1' Min. 3' Max. B) 2' Max. 2' Min. 5' Max. C) 3' Max. 4' Min. 6' Max. D) 4' Max. 6' Min. 7' Max. E) 5' Max. 8' Min. 8' Max.

Horizontal Venting with Two (2) 90o Elbows

With these options, max. total pipe length is 30 feet with min. of 8 feet total vertical and max. 8 feet total horizontal.

Please note min. 1 foot between 90o elbows is required.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Horizontal Venting with Three (3) 90o Elbows

One 90o elbow = Two 45o elbows.

INSTALLATION

Option V H V + V1 H + H1

A) 2' Min. 1' Max. 3' Min. 4' Max. B) 3' Min. 2' Max. 4' Min. 5' Max. C) 4' Min. 3' Max. 6' Min. 6' Max. D) 5' Min. 4' Max. 8' Min. 7' Max. E) 6' Min. 5 Max. 10' Min. 8' Max. F) 7' Min. 6' Max. 12' Min. 9' Max.

Vertical Venting with Two (2) 90

elbow = Two 45o elbows.

One 90

Option V H V + V1 A) 1' Min. 4' Max. 2' Min. B) 2' Min. 5' Max. 3' Min. C) 3' Min. 6' Max. 4' Min. D) 4' Min. 7' Max. 5' Min. E) 5' Min. 8' Max. 6' Min.

With these options, max. total pipe length is 30 feet with min. of 12 feet total vertical and max. 9 feet total horizontal.

Please note min. 1 foot between 90 elbows is required.

Elbows

With these options, max. total pipe length is 30 feet with min. of 6 feet total vertical and max. 8 feet total horizontal.

Please note min. 1 foot between 90 quired.

elbows is re-

Vertical Venting with Two (2) 90o Elbows

One 90o elbow = Two 45o elbows.

Option H + H1 V A) 2' Max. 2' Min. B) 3' Max. 3' Min. C) 4' Max. 4' Min. D) 5' Max. 5' Min. E) 6' Max. 6' Min.

With these options, max. total pipe length is 30 feet with min. of 6 feet total vertical and max. 6 feet total horizontal.

Please note min. 1 foot between 90o elbows is required.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

For additional vertical venting with 2 x 90o elbows, refer to page 15.

INSTALLATION

One 90o elbow = Two 45o elbows.

Vertical Venting with Three (3) 90o Elbows

Option H V H + H1 V + V1 A) 1' Max. 1' Min. 3' Max. 3' Min. B) 2' Max. 2' Min. 4' Max. 5' Min. C) 3' Max. 3' Min.' 5' Max. 7' Min. D) 4' Max. 4' Min. 6' Max. 9' Min. E) 5' Max. 5' Min. 7' Max. 11' Min.

With these options, max. total pipe length is 30 feet with min. of 11 feet total vertical and max. 7 feet total horizontal.

Please note min. 1 foot between 90o elbows is required.

Vertical Venting with Three (3) 90o Elbows

One 90

Option V H + H1 V + V1 A) 2' Min. 3' Max. 4' Min. B) 3' Min. 4' Max. 6' Min. C) 4' Min. 5' Max. 7' Min. D) 5' Min. 6' Max. 8' Min. E) 6' Min. 7' Max. 9' Min. F) 7' Min. 8' Max. 10' Min.

elbow = Two 45o elbows.

With these options, max. total pipe length is 30 feet with min. of 10 feet total vertical and max. 8 feet total horizontal.

Please note min. 1 foot between 90 required.

elbows is

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

VERTICAL TERMINATION

WITH CO-LINEAR FLEX SYSTEM

INSTALLATION

THE APPLIANCE MUST NOT BE

CONNECTED TO A CHIMNEY FLUE

SERVING A SEPARATE SOLID FUEL

BURNING APPLIANCE.

This appliance is designed to be attached to two 3" (76mm) co-linear aluminium ﬂ ex running the full length of the chimney. See the Venting Arrangements on next page for minimum and maximum heights.

Required Parts:

Part # Description

946-529 Co-linear DV Vertical Termination Cap 948-305 3" Flex - 35 ft. 946-563 Co-Axial to Co-Linear Adapter Kit which contains the following: Co-linear Flex Adapter Outer Pipe Inner Pipe Adapter 510-994 Rigid Pipe Adaptor

945 45

Alternate Approved Caps

980 Vertical Termination Cap 991 High Wind Cap 923GK

3" Co-linear Adapter with ﬂ ashing

Elbow

Masonry chimneys may take various contours which the ﬂ exible liner will accommodate. However, keep the ﬂ exible liner as straight as possible, avoid unnecessary bending.

The Air Intake pipe must be attached to the inlet air collar of the termination cap.

Co-linear DV

Vertical Termination

Cap # 946-529

A maximum

of two certified

joiner kits

may be used

per length.

Flex Liner

#948-305

35 ft (11m)

Exhaust

Flue

FPI Cabinet and/or Flat Wall Mantles may be used in these applications ensuring that clearances to combustibles are maintained.

Rigid Pipe Adaptor

# 510-994

Outer

Pipe with Kit# 946-563

Pipe Length

45 Elbow

Air Intake

Co-Linear

Flex

Adapter

with Kit#

946-563

Inner Pipe

Adapter

with Kit#

946-563

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

Venting Arrangements - Vertical Terminations

with Co-linear Flex System for both Residential & Manufactured Homes

into Masonry Fireplaces

The shaded area in the diagrams show the

allowable vertical terminations.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

HORIZONTAL INSTALLATIONS

INSTALLATION

Install the vent system according to the manufacturer's instructions included with the components.

1) Set the unit in its desired location. Check

to determine if wall studs or roof rafters are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the unit. Rough in the gas preferably on the right side of the unit and the electrical (junction block is on the left side) on the left.

2) Direct Vent pipe and ﬁ ttings are designed

with special twist-lock connections to connect the venting system to the appliance ﬂ ue outlet. A twist-lock appliance adaptor is an available option that must be used in conjunction with the Simpson Dura-Vent Direct Vent GS system.

3) Put a bead of silicone inside the outer sec-

tion of the adapter and a bead of Stove Mate on the inner collar. Slip the adapter over the existing inner and outer ﬂ ue collar and fasten to the outer collar only with the 3 supplied screws (drilling pilot holes will make this easier). Level the ﬁ replace and fasten it to the framing using nails or screws through the nailing strips.

4) Assemble the desired combination of pipe

and elbows to the appliance adaptor and twist-lock for a solid connection.

Note:

a) Twist-lock procedure: Four indentations,

located on the female ends of pipes and ﬁ ttings, are designed to slide straight onto the male ends of adjacent pipes and ﬁ ttings, by orienting the four pipe indentations so they match and slide in to the four entry slots on the male ends, Dia. 1. Push the pipe sections completely together, then twist-lock one section clockwise approximately one-quarter turn, until the two sections are fully locked. The female locking lugs will not be visible from the outside, on the Black Pipe or ﬁ ttings. They may be located by examining the inside of the female ends.

b) Horizontal runs of vent must be sup-

ported every three feet. Wall straps are available for this purpose.

5) Mark the wall for a 10" x 10" square hole.

The center of the square hole should line up with the centerline of the horizontal pipe. Cut and frame the 10 inch square hole in the exterior wall where the vent will be terminated. If the wall being penetrated is constructed of non-combustible material, i.e. masonry block or concrete, a 7"(178mm) diameter (7-1/2"(191mm) dia. for ﬂ ex) hole is acceptable.

Note:

a) The horizontal run of vent must be level,

or have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present the possibility of a ﬁ re.

b) The location of the horizontal vent termi-

nation on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. For External Vent Terminal Locations, see diagram on page 9.

c) Snorkel Terminations: For installations requiring a vertical rise

on the exterior of the building, 14-inch and 36-inch tall Snorkel Terminations and the Riser Vent as shown in Dia. 2 & 2a are available. Follow the same installation procedures as used for standard Horizontal Termination. NEVER install the snorkel upside down.

Diagram 2a

Below Grade Snorkel Installation

If the Snorkel Termination must be

installed below grade, i.e. basement application, proper drainage must be provided to prevent water from entering the Snorkel Termination. Refer to Dura-Vent Installation instructions for details. Do not attempt to enclose the Snorkel within the wall, or any other type of enclosure.

6) The arrow on the vent cap should be pointing up. Insure that the 1-1/2"

clearances to combustible materials are maintained (Dia. 3). Install the termination cap. AstroCap Termination Cap may be used.

The four wood screws provided should

be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

or Dura-Vent Horizontal

Diagram 3

Diagram 1

Note: Apply sealant "Mill-Pac" to inner pipe

and high temperature silicone sealant to outer pipe on every twist-lock joint.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

*As speciﬁ ed in CGA B149 Installation Code. Local codes or regulations may require different clearances.

Diagram 2

Note: If installing termination on a siding

covered wall, a vinyl siding standoff or furring strips must be used to ensure that the termination is not recessed into the siding.

7) Before connecting the horizontal run of vent

pipe to the vent termination, slide the Wall Thimble (Part # 620-926) over the vent pipe.

8) Slide the appliance and vent assembly to-

wards the wall carefully inserting the vent

INSTALLATION

pipe into the vent cap assembly. It is

important that the vent pipe extends into the vent cap sufﬁ cient distance so as to result in a minimum pipe overlap of 1-1/4 inches. Secure the connection between the vent pipe and the vent cap 3 sheet metal screws.

9) Install wall thimble in the center of the

10" square and attach with wood screws (Diagram 4).

Diagram 4

VERTICAL

TERMINATION

1) Maintain the 1-1/2" clearances (air spaces)

to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafter, or other nearby combustible surfaces. Do not pack air spaces with insulation. Check pages 13-17 for the maximum vertical rise of the venting system and the maximum horizontal offset limitations.

2) Set the gas appliance in its

desired location. Drop a plumb bob down from the ceiling to the position of the appliance ﬂ ue exit, and mark the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole previously drilled in the ceiling, and mark the spot where the vent will penetrate the roof.

3) A Firestop spacer must be installed in the

ﬂ oor or ceiling of every level. To install the Firestop spacer in a ﬂ at ceiling or wall, cut a 10 inch square hole. Frame the hole as shown in Diagram 2 and install the ﬁ restop.

Diagram 1

4) Assemble the desired lengths of pipe and

elbows. Ensure that all pipes and elbow connections are in the fully twist-locked position and sealed.

Note: Apply sealant "Mill-Pac" to inner pipe

and high temperature silicone sealant to outer pipe on every twist-lock joint.

5) Cut a hole in the roof centered on the small

drilled hole placed in the roof in Step 2. The hole should be of sufﬁ cient size to meet the minimum requirements for clearance to combustibles of 1-1/2". Slip the ﬂ ashing under the shingles (shingles should overlap half the ﬂ ashing) as per Diagram 3.

Diagram 3: The upper half of the ﬂ ashing is installed under the rooﬁ ng material and not

nailed down until the chimney is installed. This

allows for small adjustments.

6) Continue to assemble pipe lengths.

Note: If an offset is necessary in the attic to

avoid obstructions, it is important to support the vent pipe every 3 feet, to avoid excessive stress on the elbows, and possible separation. Wall straps are available for this purpose.

Galvanized pipe is desirable above the rooﬂ ine

due to its higher corrosion resistance. Continue to add pipe sections through the ﬂ ashing until the height of the vent cap meets the minimum height requirements speciﬁ ed in Dia. 4 or local codes. Note that for steep roof pitches, the vertical height must be increased. A poor draft, or down drafting can result from high wind conditions near big trees or adjoining roof lines, in these cases, increasing the vent height may solve the problem.

Diagram 4

Roof Pitch Minimum Vent Height

Feet Meters

ﬂ at to 7/12 2 0.61

over 7/12 to 8/12 2 0.61

over 8/12 to 9/12 2 0.61

over 9/12 to 10/12 2.5 0.76

over 10/12 to 11/12 3.25 0.99

over 11/12 to 12/12 4 1.22

over 12/12 to 14/12 5 1.52

over 14/12 to 16/12 6 1.83

over 16/12 to 18/12 7 2.13

over 18/12 to 20/12 7.5 2.29

over 20/12 to 21/12 8 2.44

8) Install the vertical termination cap by twist-

locking it.

Note: Any closets or storage spaces, which

the vent passes through must be enclosed.

GAS LINE

INSTALLATION

The gas line is brought through the right side of the appliance. The gas valve is situated on the right hand side of the unit and the gas inlet is on the right hand side of the valve.

The gas line connection may be made of rigid pipe, copper pipe or an approved ﬂ ex connector. (If you are using rigid pipe, ensure that the valve can be removed for servicing.) Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN/CGA B149 installation code.

For USA installations follow local codes and/or the current National Fuel Gas Code, ANSI Z223.1.

When using copper or ﬂ ex connectors use only approved ﬁ ttings. Always provide a union so that gas lines can be easily disconnected for servicing. Flare nuts for copper lines and ﬂ ex connectors are usually considered to meet this requirement.

Diagram 2

7) Ensure vent is vertical and secure the base

of the ﬂ ashing to the roof with rooﬁ ng rails, slide storm collar over the pipe section and seal with a mastic.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Important: Always check for gas leaks with a soap and water solution or gas leak detector. Do not use open ﬂ ame for leak testing.

INSTALLATION

PILOT ADJUSTMENT

Periodically check the pilot ﬂ ames. Correct ﬂ ame pattern has three strong blue ﬂ ames: 1 ﬂ owing around the thermopile, 1 around the thermocouple and 1 ﬂ owing across the burner (it does not have to be touching the burner).

Note: If you have an incorrect ﬂ ame pattern, contact your Regency dealer for further instructions.

Incorrect ﬂ ame pattern will have small, probably yellow ﬂ ames, not coming into proper contact with the rear burner or thermopile or thermocouple.

P33-NG3 System Data

Conversion Kit# 431-969

For 0 to 2000 feet altitude

Burner Inlet Oriﬁ ce Sizes: # 4 4 Max. Input Rating 22,500 Btu/h Min. Input Rating 12,500 Btu/h

For 2000 to 4500 feet altitude

Burner Inlet Oriﬁ ce Sizes: # 4 5 Max. Input Rating 21,000 Btu/h Min. Input Rating 10,500 Btu/h

Supply Pressure min.5.0" w.c.

Manifold Pressure (High) 3.8"+/- 0.2" w.c.

P33-LG3 System Data

For 0 to 4500 feet altitude

Burner Inlet Oriﬁ ce Sizes: #54

Max. Input Rating 21,500 Btu/h Min. Input Rating 10,500 Btu/h

Supply Pressure min.12.0" w.c.

Manifold Pressure (High) 11"+/- 0.2"w.c.

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both

inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1) Make sure the valve is in the "OFF" posi-

tion.

2) Loosen the "IN" and/or "OUT" pressure

tap(s), turning counterclockwise with a 1/8" wide ﬂ at screwdriver.

3) Attach manometer to "IN" and/or "OUT"

pressure tap(s) using a 5/16" ID hose.

4) Light the pilot and turn the valve to "ON"

position.

5) The pressure check should be carried out

with the unit burning and the setting should be within the limits speciﬁ ed on the safety label.

6) When ﬁ nished reading manometer, turn

off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" ﬂ at screwdriver. Note: Screw should be

snug, but do not over tighten.

HIGH ELEVATION

This unit is approved in Canada for altitude to 4500 ft. (CAN/CGA-2.17-M91). For Natural Gas installations above 4500 ft. follow current CAN/CGA-B149.1.

S.I.T. VALVE DESCRIPTION

1) Gas cock knob

2) Manual high/low adjustment

3) Pilot Adjustment

4) Thermocouple Connection - option

5) Outlet Pressure Tap

6) Inlet Pressure Tap

7) Pilot Outlet

8) Main Gas Outlet

9) Alternative TC Connection Point

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

Conversion Kit from Natural Gas to Propane Model #431-969

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

for P33-3 using SIT 820 NOVA Gas Valve

Conversion Kit Contains:

Qty. Part # Description 1 910-018 SIT Conversion Kit-50% Turndown LP 1 910-037 LP Injector (Pilot Oriﬁ ce) 1 904-163 Burner Oriﬁ ce #54 1 908-255 Decal "Converted to Propane" 1 908-528 Red "PROPANE" label 1 908-529 5/32" Allen Key 1 908-812 Instruction Sheet

1) Shut off the gas supply.

2) Remove the louvers (and bay door if it is

installed).

3) Open the ﬂ ush door and remove the door.

4) Remove the logs and embers/rockwool.

5) Remove the 2 screws holding the Burner

Assembly to the ﬁ rebox base. Push the Burner Assembly to the left and lift out.

7) Unscrew the pilot oriﬁ ce with the allen key

and replace with the LP pilot oriﬁ ce in the kit and replace pilot cap.

8) Remove burner oriﬁ ce with a 1/2" wrench

and discard. Use another wrench to hold on to the elbow behind the oriﬁ ce.

Remove the 2 screws, push Burner

Assembly to the left and lift out.

6) Pull off the pilot cap to expose the pilot

oriﬁ ce.

Burner Oriﬁ ce

9) Reinstall new burner oriﬁ ce LP stamped #54

and tighten.

10) Remove and discard the 3 pressure regula-

tor mounting screws (A), pressure regulator tower (B) and diaphragm (C).

11) Insure that the rubber gasket (D) is properly

positioned and install the new HI/LO pressure regulator assembly to the valve using the new screws (E) supplied with the kit. Tighten screws securely.

12) Reverse steps 5) to 2).

13) Attach clear label "This unit has been con-

verted to Propane" near or on the serial # decal. Attach white label "This valve has been converted from NG to LPG using SIT conversion Kit Code 0.907.202" onto the valve.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

14) Replace yellow "Natural Gas" label with red

"Propane" label

15) Check for gas leaks.

16) Check inlet and outlet pressures.

17) Check operation of ﬂ ame control.

18) Check for proper ﬂ ame appearance and

glow on logs.

INSTALLATION

OPTIONAL BRICK

PANE LS

1) Undo the bottom 2 door latches and open

and remove glass door. Remove logs.

2) Attach the 2 Rear Brick Retaining clips to

the rear wall. Loosen the screws in the top and rear wall of the ﬁ rebox and slide the retaining clips into position (tight against the ﬁ rebox top) and then tighten the screws.

Note: The logs must not be in the unit.

3) Insert the back brick panel by carefully slip-

ping it between the back wall of the ﬁ rebox and the rear log bracket.

LOG SET INSTALLATION

D) 251 A) 250

Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot operation.

Log Kit # 431-930 contains the fol-

The 3-digit numbers (i.e. 250) are

molded into the rear of each log.

lowing pieces:

A) 250 Rear Log 902-250 B) 254 Middle Cross Log 902-254 C) 253 Front Left Cross Log 902-253 D) 251 Rear Left Log 902-251 E) 252 Front Right Cross Log 902-252 F) Embers 902-156 G) Vermiculite 902-179/21 H) Rockwool 902-153

NOTE: If you will be installing the optional

Brick Panels, install the Brick Panels prior to installing the logs.

C) 253

4) Place Log 254 on the front right side of the burner. Push the back of the log against the 2 brackets with the notch on the bottom right side of the log ﬁ tting into the right side of the grate.

B) 254 E) 252

254

Notch

4) Put the side panels in next. Slide them in

from the front and push them ﬂ at up against the wall. Be very careful not to scratch them on the ﬁ rebox hardware.

5) Slide the Top Brick Panel into position and

slide the Top Brick Retaining clips so that they hold the Top Brick Panel in place and tighten down the screws.

1) Carefully remove the logs from the box and unwrap them. The logs are fragile, handle with care - do not force into position.

2) Sprinkle the vermiculite and embers around the ﬁ rebox base.

Vermiculite

3) Place the Log 250 on the rear log support pins with the ﬂ at side to the back.

Vermiculite

250

Vermiculite

Bracket

250

254

5) Position Log 253 across the cutouts in Logs 250 and 254 with the notch on the left side of the log ﬁ tting into the 2nd grate tab.

253

Bracket

Cutouts

250

254

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

2nd Grate Tab

INSTALLATION

250

8) Pull off ember size pieces of rockwool and gently place them on the front of the burner tray in the places shown in the photo below. Do not compress the rockwool, leave it loose.

253

6) Place the bottom left front edge of Log 251 against the left edge of the burner tray and rest the log on the cutout on Log

253.

251

253

7) Position Log 252 across the cutouts in Logs 254 and 253. The notch in the bottom right end ﬁ tting against the 5th grate tab.

254

250

254

Cutout

Place rockwool in these 2 locations

on the burner tray.

9) Test ﬁ re to ensure proper light off (make sure ﬂ ame ﬂ ows smoothly from one end of burner to the other). If there is any ﬂ ame hesitation, check that area for any blockage of the burner ports.

10) Install ﬂ ush glass and bay glass (if used) as

STANDARD FLUSH

DOOR

Diagram 1

Diagram 2

Use the hook to pull the spring out until you can put the hook into the slot on the bottom door bracket. Repeat for 2nd spring. See diagram 3.

253

251

253

254

5th Grate Tab

254

252

250

252

The standard ﬂ ush door comes with a black frame. To install the frame, simply hook the top door ﬂ ange onto the top of the unit and swing the door towards the unit, diagram 1. Be careful that the glass gasket does not roll up; there must be a gap between the gasket and the door lip to ensure that the door sits securely on the unit. Diagram 2.

To remove the ﬂ ush door, reverse the above steps.

Diagram 3

Optional Flush Trim

Attach the round magnets to the back of the top trim piece and to the bottom trim piece, then attach trim to the top and bottom of Flush door.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

FLUSH LOUVERS

1) Install the top louver by sliding the two

bracket clips into the brackets located underneath the top of the ﬁ rebox.

2) Install the bottom louver by folding the louver

down and then sliding the Bottom Louver bracket down onto the 2 pins on the base of the unit (dia. 1). Secure with 1 screw as per dia. 2.

Diagram 1 Diagram 2

DOUBLE SCREEN

DOOR

1) Pull out the top louver.

2) Center the screen door and hook over the ﬂ ush door.

3) Open the screen door(s) and secure the screen door to the ﬂ ush door front with 2 clips on the bottom left and right side.

Note: Top and bottom louvers are different.

3) Open the bottom louver. Pull the Burner

ON/OFF control box from inside the bottom of the ﬁ replace and position the slots in the bracket over the 2 screws on the left side of the bottom louver. Push down to lock into place. Tighten the screws.

Screws on lou-

ver bracket

Burner ON/OFF

control box

Clip locations

Clip installed on right side.

OPTIONAL BAY DOOR

The Bay louvers MUST be used

with the Bay glass option.

The optional Bay door is an overlay on the ﬂ ush front. The standard ﬂ ush door and glass

must remain on the unit.

1) Hook the top of the bay door over the ﬂ ush door ﬂ ange and swing the bottom against the bottom ﬂ ange of the ﬂ ush door.

Note: If any maintenance etc. must be done

in the ﬁ rebox, ﬁ rst remove the Bay louvers and door.

Optional Bay Trim

Attach 4 supplied magnets each to the back of the top and bottom trim pieces, and attach trim to the top and bottom of Bay door.

2) Secure to the ﬂ ush door bottom bracket with 2 screws provided.

3) Slide the valve extension knobs onto the valve knobs.

Burner ON/OFF control box attached to bot-

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

tom ﬂ ush louver.

INSTALLATION

BAY LOUVERS

1) Remove ﬂ ush louver top heat shield by removing the 4 screws.

Flush Louver Top

Heat Shield

2) Install the bay louver top heat shield and secure with 4 screws.

4) Install bottom louver by sliding the two bracket clips into the brackets

located underneath the bay door. Secure with 1 screw into each Bottom Louver Mounting Bracket as per diagram below. Use the bottom hole in the bracket.

5) Slide the valve extension knobs onto the valve knobs. Match the

correct ext. knob with the valve knob.

Bay Louver Top

Heat Shield

3) Install top louver by sliding the two bracket clips into the brackets

located on top of the bay door. See below. The ﬁ tted louver leaves a small gap between faceplate bottom and louver top.

6) Open the bottom louver. Pull the Burner ON/OFF control box from

inside the bottom of the ﬁ replace and position the slots in the bracket over the 2 screws on the left side of the bottom louver. Push down to lock into place. Tighten the screws.

Burner ON/OFF

control box

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

FULL SCREEN FRONT

INSTALLATION

1) Before beginning the installation, remove the Glass Door from the

unit. Refer to the manual for instructions.

2) Slide the Bottom Face Plate Bracket into the bottom of the unit,

secure it into the pins located on the inside of the ﬁ re box. Once the bracket is in place, tighten the screws into the hinges on the left and right sides.

Bottom Faceplate Bracket

Pin location

4) a) Before attaching the Full Screen Door Frame to the unit,

loosen the left and right side #8 Self Tapping Philips screws located on the inside top of the outer frame of the appliance. Also remove the center screw.

b) Slide the cut-outs in the Top and Bottom Flange of the Full

Screen Door Frame under the screw heads which were loosened in step 4a). Once the Frame is in place, tighten the screws to secure. Also re-secure the top center screw

through the oblong hole.

Full Screen Door Frame

Faceplate Mounting Bracket

3) Before attaching the Full Screen Door Frame, remove the Screen

Doors from the Full Screen Door Frame by fully opening the doors and lifting up off of the hinges. See important note in step 10.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Screw

Backside of Full

Screen Door

Frame Shown

Cut-Out

Oblong Hole

Cut-Out

Top

Flange

Bottom Flange

Cut-Outs

INSTALLATION

NOTE: Should the ﬁ nished wall protrude beyond the face of the unit,

you can accommodate up to 1/2" depth.

Simply push in the Full Screen Door Frame until it aligns against

the ﬁ nished wall. Secure Top Flange of Full Screen Door Frame as described in step 4 b).

For the Bottom Flange of the Full Screen Door Frame, push the bot-

tom of the Frame until it aligns with the wall. Use the inner cut-outs to secure the base of the Frame using the 2 x #8 Self Tapping Phillips screws provided.

5) Install the Hinges to the Hinge Brackets on the left and right side of the Bottom Faceplate Bracket (seen in step 2), secure using 2 x #8 Self Tapping Philips screws per hinge.

8) Re-install Glass Door. Refer to the manual for instructions.

9) Slide the Top Grill into the louver brackets located on the inside top

of the ﬁ rebox. Push in place.

Top Grill

6) Place the Bottom Frame near the hinges, and ﬂ ip down the hinges

from the Bottom Face Plate. Secure the hinges in place to the Bottom Frame, using 2x #8 Self Tapping Phillips screws per hinge.

Hinge Location

Bottom Grill

7) Mount the Burner ON/OFF Control Box to the left side of the Bottom

Grill using 2 x #8 - 1/4" Philips Head Screws.

Left Side

of Bottom

Grill

10) Install the Left and Right Side Screen Doors in the fully open position

by placing over top of the hinges on the Full Screen Door Frame.

NOTE: Failure to install the doors in the fully open position could

result in paint damage to the surface of the door.

Hinge

Burner ON/OFF

Control Box

Screen Door

11) Close screen doors.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

OPTIONAL

WALL THERMOSTAT

A wall thermostat may be installed if desired, connect the wires as per the wiring diagram. Use table below to determine the maximum wire length.

Note: Preferable if the thermostat is installed

on an interior wall.

Regency offers an optional programmable thermostat but any 250-750 millivolt rated nonanticipator type thermostat that is CSA, ULC or UL approved may be used.

CAUTION

Do not wire millivolt

wall thermostat wires

to 120V wire.

Thermostat Wire Table

Recommended Maximum Lead Length

(Two-Wire) When Using Wall

Thermostat (CP-2 System)

Wire Size Max. Length

14 GA. 16 GA. 18 GA. 20 GA. 22 GA.

50 Ft. 32 Ft. 20 Ft. 12 Ft.

9 Ft.

OPTIONAL

REMOTE CONTROL

Use the Regency Remote Control Kit approved for this unit. Use of other systems may void your warranty.

The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate.

1) Choose a convenient location on the wall

to install the receiver and the receptacle box (protection from extreme heat is very important). Run wires from the ﬁ replace to that location. Use Thermostat Wire Table.

2) Connect the two wires to the gas valve.

See diagram below.

CAUTION

Do not wire millivolt

remote control wires

to 120V wire.

3) Install 3 AAA alkaline batteries in transmitter

and 4 AA alkaline batteries in the receiver. Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote control is now ready for operation.

OPTIONAL

WALL SWITCH

1) Run the supplied 15' of wire through the right

or left side gas inlet opening. Be careful not to damage wire.

Note: We recommend a maximum of 15'

of wire but if you wish to go with a longer run, use the Thermostat Wire Table.

2) Connect the wire to the supplied wall switch

and install into the receptacle box.

CAUTION

Do not wire millivolt

wall switch wire

to 120V wire.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

WIRING DIAGRAM

This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat will continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.

(Do not cut the ground terminal off under any circumstances.)

NOTE: Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit)

in case the fan is installed at a later date.

Lockwasher

Star washer

ground wire

Burner

OFF

Thermostat

Fan

#8 Ground Lug

Nut

White

Red

Black

(mobile home

approved)

Assembly

Piezo Ignitor

Pilot

(To THTP)

(To TH)

Thermopile

Gas Pilot

Thermocouple

Electrode

120V AC 60 Hz

To Thermocouple IN

Neutral

Live

Ground

ON OFF

Rotary Speed

Brown

White

Green

Control

"S.I.T" Valve

Black Red Red

Minimum Convection

Fan

Air Temp. Switch

Gas In

Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges.

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

T-Stat

Remote Receiver

or Thermostat

(Millivolt) (Optional)

ON OFF

Regency

Remote Transmitter

(Optional)

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

INSTALLING THE OPTIONAL FAN

INSTALLATION

120 Volt AC power is needed for the fan switch and blower. The fan can be hard wired if desired. The receptacle box should be installed on the left hand side of the unit by a qualiﬁ ed electrician. The neutral (wider) slot of the polarized receptacle should be at the top.

Unit must be grounded at all times. Do not cut the ground terminal off under any circumstances.

1) Shut the power off.

2) Remove the standard ﬂ ush door and the

optional bay door, if installed. Open the bottom louver door.

3) Loosen the 2 screws holding the Burner

ON/OFF switch and bracket to the bottom louver and lift the assembly out.

4) Turn the fan base on its side (with the base

facing towards you) and then slide the fan in towards the rear of the unit. Turn the fan upright and slip it over the two mounting studs. Take care not to damage the insulation on the fan base. Ensure that the fan blades

do not rub against the valve tubing.

Diagram 1.

5) Connect fan ground cable to ground lug.

Refer to wiring diagram.

6) Slide the thermodisc/cover assembly into

the bracket clip on the underside of the ﬁ rebox. Check that no wire will touch the hot surfaces. Diagram 2.

7) Attach the Fan control box to the Burner

ON/OFF control box. Diagram 3.

Diagram 2

Diagram 3: Use the clip & hook on the side of

the control boxes to join them together.

8) Secure the two boxes together with one

screw.

Secure the 2 boxes together

with one screw.

9) Position the control box assembly on the

bottom louver and mark the position of the slot on the right side bracket.

Hold control box assembly in place and

mark the position of the right side slot

10) Remove the control box assembly and push

the hold-down clip onto the louver. Bend the tab until it is at 90

to the louver.

11) Attach the two control boxes to the bottom

louver and tighten the 2 screws on the left side and 1 screw on the right side.

Secure left side with 2 screws.

Secure right side with one screw.

12) Secure the fan wires and power cord by

attaching one of the adhesive backed wire holder clips (Part #910-199) onto the stove base. Use the second clip to bundle up the wires approximately 4" from the control box. Ensure that there is no interference with the wires when the louver is closed and that no wire will touch the hot metal surfaces or sharp edges.

13) Plug the fan power cord into the rear end of

the receptacle box to provide the maximum clearance from the louvers.

TO REMOVE THE FAN

1) Shut the power off.

2) Reverse the above instructions.

Note: The bearings are lubricated for life.

Do not lubricate them. Make sure you vacuum the fan area on a regular basis.

Diagram 1

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Push hold-down clip onto inside

louver and press tab until it is

at 90o to

louver.

These fans collect a lot of dust from within

IMPORTANT:

your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan blades and housing using a soft brush nozzle.

OPERATING INSTRUCTIONS

COPY OF THE LIGHTING PLATE INSTRUCTIONS

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

OPERATING INSTRUCTIONS

OPERATING

INSTRUCTIONS

1) Read and understand these instructions

before operating this appliance.

2) Check to see that all wiring is correct and

enclosed to prevent possible shock.

3) Check to ensure there are no gas leaks.

4) Make sure the glass in the door frame is

properly positioned. Never operate the appliance with the glass removed.

5) Verify that the venting and cap are unob-

structed.

6) Ensure that the brick panels are installed.

7) Verify log placement. If the pilot cannot be

seen when lighting the unit, the logs have been incorrectly positioned.

8) The unit should never be turned off, and on

again without a minimum of a 60 second wait.

LIGHTING PROCEDURE

IMPORTANT

To ignite or reignite the pilot,

you must ﬁ rst release the ten-

sion springs below the door.

Only when the pilot holds, without pressure being applied to the control knob, reapply the tension springs to the door. The unit must not be operated with the tension springs unattached.

IMPORTANT: Gas cock knob cannot be turned from "PILOT" to "OFF" unless it is partially depressed.

1) Turn burner OFF using "ON/OFF" switch.

2) Turn gas control knob so indicator points to

"OFF" position and allow 5 minutes for any gas in the combustion chamber to escape.

3) Turn gas control knob counterclockwise

so indicator points to the "PILOT" position. Depress the gas control knob fully. Depress the igniter button several times until the pilot lights. After approximately one minute, release the gas control knob. The pilot ﬂ ame should continue to burn. If the pilot does not remain lit, repeat operation allowing a longer period before releasing gas control knob.

4) When the pilot stays lit, turn the gas knob

further counterclockwise to the "ON" position.

5) Use the wall switch, thermostat or remote

control to turn on the unit.

6) Rotate the ﬂ ame height regulator to adjust

the ﬂ ame height higher or lower.

SHUTDOWN

PROCEDURE

1) Use the wall switch, thermostat or remote

control to turn off the main burner.

2) Turn the main gas control clockwise to the

"OFF" position to turn off the pilot.

3) Turn off all electric power to appliance if

service is to be performed.

FIRST FIRE

The ﬁ rst ﬁ re in your stove is part of the paint curing process. To ensure that the paint is properly cured, it is recommended that you burn your ﬁ replace for at least four (4) hours the ﬁ rst time you use it with the fan on.

When ﬁ rst operated, the unit will release an odour caused by the curing of the paint, the burning off of any oils remaining from manufacturing. Smoke detectors in the house may go off at this time. Open a few windows to ventilate the room for a couple of hours.

The glass panel may require cleaning after the unit has cooled down. DO NOT ATTEMPT TO

CLEAN THE GLASS WHILE IT IS HOT.

Note: When the glass is cold and the appli-

ance is lit, it may cause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.

DO NOT BURN THE APPLIANCE WITHOUT THE GLASS FRONT IN PLACE.

During the ﬁ rst few ﬁ res, a white ﬁ lm may develop on the glass front as part of the curing process. The glass should be cleaned or the ﬁ lm will bake on and become very difﬁ cult to remove. Use a non-abrasive cleaner and NEVER clean the glass while it is hot.

AERATION

ADJUSTMENT

The air shutter can be adjusted by moving the adjusting wire up or down. The wire is accessed through the bottom louver opening. Open the air shutter for a blue ﬂ ame or close for a yellower ﬂ ame. The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude.

Minimum Air Shutter Opening: 3/16" Natural Gas 3/8" Propane

CAUTION: Carbon will be produced if air shutter is closed too much.

Air

shutter

wire

Adjustment Wire: push to close

or pull to open aeration cap

Closed - Tall yellow

Open - Short blue

Note: Any damage due to carboning result-

ing from improperly setting the aeration controls is NOT covered under warranty.

Note: Aeration Adjustment should only be

performed by an authorized Regency Installer at the time of installation or service.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

MAINTENANCE

NORMAL OPERATING

SOUNDS OF

GAS APPLIANCES

It is possible that you will hear some sounds from your gas appliance. This is perfectly normal due to the fact that there are various gauges and types of steel used within your appliance. Listed below are some examples. All are normal operating sounds and should not be considered as defects in your appliance.

Blower:

Regency gas appliances use high tech blowers to push heated air farther into the room. It is not unusual for the fan to make a "whirring" sound when ON. This sound will increase or decrease in volume depending on the speed setting of your fan speed control.

Burner Tray:

The burner tray is positioned directly under the burner tube(s) and logs and is made of a different gauge material from the rest of the ﬁ rebox and body. Therefore, the varying thicknesses of steel will expand and contract at slightly different rates which can cause "ticking" and "cracking" sounds. You should also be aware that as there are temperature changes within the unit these sounds will likely re-occur. Again, this is normal for steel ﬁ reboxes.

Blower Thermodisc:

When this thermally activated switch turns ON it will create a small "clicking" sound. This is the switch contacts closing and is normal.

Pilot Flame: While the pilot ﬂ ame is on it can make a very slight "whisper" sound.

Gas Control Valve: As the gas control valve turns ON and OFF, a dull clicking sound may be audible, this is normal operation of a gas regulator or valve.

Unit Body/Firebox: Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process.

MAINTENANCE INSTRUCTIONS

1) Always turn off the gas valve before cleaning.

For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean paint brush as the logs are fragile and easily damaged.

2) Clean appliance and door with a damp

cloth (never when unit is hot). Never use an abrasive cleaner. The glass should be cleaned with a gas ﬁ replace glass cleaner.

The glass should be cleaned when it starts looking cloudy.

3) The heater is ﬁ nished in a heat resistant

paint and should only be reﬁ nished with heat resistant paint. Regency uses StoveBright Paint - Metallic Black #6309.

4) Make a periodic check of burner for proper

position and condition. Visually check the ﬂ ame of the burner periodically, making sure the ﬂ ames are steady; not lifting or ﬂ oating. If there is a problem, call a qualiﬁ ed service person.

5) The appliance and venting system must be

inspected before use, and at least annually, by a qualiﬁ ed ﬁ eld service person, to ensure that the ﬂ ow of combustion and ventilation air is not obstructed.

Note: Never operate the appliance without

the glass properly secured in place.

6) Do not use this appliance if any part has been

under water. Immediately call a qualiﬁ ed service technician to inspect the appliance and to replace nay part of the control system and any gas control which has been under water.

7) Verify operation after servicing.

General Vent Maintenance

Conduct an inspection of the venting system semi-annually. Recommended areas to inspect as follows:

3) Check for evidences of excessive condensa-

tion, such as water droplets forming in the inner liner, and subsequently dripping out the joints, Continuous condensation can cause corrosion of caps, pipe, and ﬁ ttings. It may be caused by having excessive lateral runs, too many elbows, and exterior portions of the system being exposed to cold weather.

4) Inspect joints, to verify that no pipe sections

or ﬁ ttings have been disturbed, and consequently loosened. Also check mechanical supports such as Wall Straps, or plumbers' tape for rigidity.

GOLD-PLATED or

BRASS LOUVERS/TRIM

The 24 carat gold-plated or brass ﬁ nish on the louvers and trim requires little maintenance, and need only be cleaned with a damp cloth. DO NOT use abrasive materials or chemical cleaners, as they may harm the ﬁ nish and void the warranty. Clean any ﬁ ngerprints off before

turning the unit on.

LOG REPLACEMENT

The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door and carefully remove the logs. (The pilot light generates enough heat to burn someone.) If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the diagrams under Log Installation.

Note: Improper positioning of logs may cre-

ate carbon build-up and will severely alter the unit's performance which is not covered under warranty.

1) Check the Venting System for corrosion in

areas that are exposed to the elements. These will appear as rust spots or streaks, and in extreme cases, holes. These components should be replaced immediately.

2) Remove the Cap, and shine a ﬂ ashlight

down the Vent. Remove any bird nests, or other foreign material.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

MAINTENANCE

THERMOPILE/

THERMOCOUPLE

1) Open the bottom louvers.

2) Loosen the thermocouple or thermopile with

a 7/16" wrench.

3) Disconnect thermocouple by loosening nut

from the valve with a 9mm wrench. Disconnect thermopile by loosening 2 screws marked TP on the valve.

4) Drop the thermocouple or thermopile down

from the bracket and pull it out of the unit.

5) Reinstall the new ones in reverse order.

GLASS GASKET

If the glass gasket requires replacement use 5/8" ﬂ at glass gasket for the Bay Front (Part # 936-243) and a tadpole glass gasket for the Flush Front (Part # 936-155).

DOOR GLASS

Flush Glass Replacement

Remove the ﬂ ush door front. Remove the 4 glass clips from each corner. Slide in the new replacement glass. Push the 4 glass clips back onto the frame. The glass must have gasket-

ing around it.

Bay Glass Replacement

1) Remove the door from the unit and place on

a soft surface to prevent scratching.

2) Remove the nuts holding the glass clips in

place and remove.

3) Replace the glass. The glass must have gasketing around it.

5) Reverse the previous steps, replace the glass

clips and fasten with the nuts but do not over tighten, as this can break the glass.

6) Replace door on the stove and check the seal.

Your Regency stove is supplied with high temperature, 5 mm Neoceram ceramic glass that will withstand the highest heat that your unit will produce. If your glass requires cleaning, we recommend using an approved glass cleaner available at all authorized dealers. Do not use abrasive materials. Do not clean the glass when hot.

In the event that you break your glass by impact, purchase your replacement from an authorized Regency dealer only, and follow our step-by-step instructions for replacement.

WARNING: Do not operate the appliance with the glass panels removed, cracked or broken. Replacement of the glass panels should be done by a licensed or qualiﬁ ed service person.

Caution: Wear gloves when removing damaged or broken glass.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

MAINTENANCE

REMOVING VALVE

1) Shut off the gas supply.

2) Remove the louvers (and bay door if it is

on).

3) Open the ﬂ ush door and remove the door.

4) Remove the logs.

5) Remove the burner/grate assembly by

removing the two Phillips head screws and then lift the burner assembly out.

Diagram 1: Remove the left and right screws

and then lift out the burner/grate assembly.

6) Remove the rear log stand by removing the

2 screws.

7) Disconnect the inlet gas line. See diagram

8) Disconnect the 2 TP wires and the 2 TH

wires from the valve.

9) Remove the 10 Phillips head screws secur-

ing the valve tray assembly in place (diagram

2) and then lift the entire assembly out (diagram 3).

screws

10) Undo the pilot tube from the valve with a 7/16" wrench.

Diagram 3: Lift out Valve Tray Assembly

11) Undo the quick drop out thermocouple nut

on the valve with a 9mm (metric) wrench.

12) Remove the Piezo igniter wire and push button assembly.

13) Undo the "gas out" ﬂ are nut with a 13/16" wrench.

Undo the "gas out" ﬂ are ﬁ tting with an 11/16"

14) wrench.

15) Remove the 4 Phillips head screws from the sides of the valve bracket and remove valve.

Hint: If you are using black pipe, ensure that there is a union by the valve, otherwise removal will be almost impossible.

Rear Log Stand

INSTALLING VALVE

1) Attach the valve to the valve bracket with

the 4 (m5x8 metric) screws provided.

2) Reconnect the "gas out" ﬂ are ﬁ tting with

an 11/16" wrench.

3) Reconnect the "gas out" ﬂ are nut with a

13/16" wrench.

4) Install piezo ignitor push button assembly

and reconnect wire.

5) Reconnect the quick drop out thermocouple

nut with a 9mm wrench.

6) Reconnect the pilot tube nut with a 7/16"

wrench.

7) Scrape off the old gasket from the ﬂ oor of the

ﬁ rebox and from the valve tray assembly.

8) Install a new gasket and reinstall the valve

tray assembly.

Note: Failure to install a new gasket may

severely affect the appliance performance.

9) Reinstall the 10 hold down screws.

10) Hook up the 2 TP and 2 TH wires to the

appropriate connections on the valve.

11) Reinstall the front log stand.

12) Install Burner/grate assembly.

13) Hook up the gas line and check for gas

leaks with a soap and water solution or a gas leak detector. (Do not use open ﬂ ame for leak testing.)

14) Fire up the unit temporarily.

15) Check the manifold pressure.

16) Reinstall the logs and brick panels as

needed.

screws

Diagram 2: Rear Log Stand & Valve Tray Assembly

Valve Tray Assembly

17) Close the door and replace the louvers.

18) Fire up the unit again and check for proper

ﬂ ame appearance and glow on logs.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

PARTS LIST

Main Assembly

Part # Description Part # Description Part # Description

1) 948-247 Door Handle

2) * Thermodisc Bracket

7) 910-428 Duplex Receptacle

8) 910-429 Box - Receptacle

9) 910-430 Cover - Receptacle

10) 904-687 Clamp Connector

13) 948-045 #12 Jack Chain

14) 948-115 Door Extension Spring

16) * Thermodisc Top

17) * Thermodisc Box Base

19) 430-129 Receptacle Box Mount

20) 430-031 Top Nailing Strip

21) 430-032 Side Nailing Strip

22) 433-017 Firebox Bafﬂ e

23) 433-011F Top Standoff

24) 511-044 Standoff - Side 790-091 Standoff - Rear

26) * Louver Hold Down

27) * Outer Flue Collar

28) * Inner Flue Collar Assembly

30) * Gasket - Flue Collar

31) * Flue Mounting Plate

432-928 Brick Panel Set - Standard 432-901 Brick Panel Set - Standard Brown 432-902 Brick Panel Set - Standard Red 432-903 Brick Panel Set - Herringbone

Brown

432-904 Brick Panel Set - Herringbone Red

33) * Brick Panel - Rear

34) * Brick Panel - Left Side

35) * Brick Panel - Right Side

36) * Brick Panel - Top

37) 430-056 Brick Clip - Top

38) 430-057 Brick Clip - Bottom

432-945 Herringbone Brick Panel Set (Optional) 902-359 Brick Panel - Rear 902-358 Brick Panel - Left Side 902-360 Brick Panel - Right Side 902-361 Brick Panel - Top

432-917 Fan Assembly (120 Volts) Optional

42) 910-331/P Fan Motor (120 Volts) 432-966 Fan Switch Assy (120 Volts)

43) 910-813 Power Cord (120 Volts)

46) 910-330 Fan Speed Control

47) 904-586 Knob - Speed Control

49) 910-142 Thermodisc - Fan Auto ON/OFF

50) 904-713 U-Clip at Louver 432-967 Burner On/Off Switch Assy

63) 910-241 Switch - Burner On/Off 910-899 Wire Harness - Valve to Burner

946-556 Optional Heat Wave Duct Kit

89) 946-004 Junction Box

90) 946-000 Round Duct Adaptor

91) 946-002 Round to Oval Adaptor

92) 946-001 Oval Duct Adaptor

93) 946-007 Angle Bracket

94) 946-517/P Fan Assembly - HeatWave Option

95) 946-006 Grill Plate - White

96) 946-005 Wall Adaptor Plate - White

97) 910-417 Knob - White

98) 910-366 Switch Cover Plate - White

99) 910-412 Fan Speed Controller

100) 910-367 Box - Plastic Switch Receptacle

102) 946-010 Flexible Air Duct 946-038 Insulation 6" dia. x 24"

104) 690-022F Cover Plate

510-994 Dura-Vent Adaptor 918-262 Manual 431-969 Conversion Kit - NG to LP

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

PARTS LIST

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

PARTS LIST

Burner & Log Assembly

Part Description

53) 430-055 Gasket - Valve Access Plate - NG/LP

54) 910-421 Pilot ON/OFF Extension Knob

55) 910-422 Flame HI/LOW Extension Knob

56) 910-190 Piezo Ignitor and Nut

433-574/P Valve Assy - Natural Gas 433-576/P Valve Assy - Propane

57) 910-378 S.I.T. Valve - Natural Gas 910-380 S.I.T. Valve - Propane

58) * Valve Bracket

59) * Firebox Base

60) * Valve Tray

66) 910-038 Pilot Assy - 3 way ﬂ ame - S.I.T. - NG 910-039 Pilot Assy - 3 way ﬂ ame - S.I.T. - LP 904-568 Oriﬁ ce #44 - Natural Gas 904-163 Oriﬁ ce #54 - Propane 936-170 Oriﬁ ce Gasket

67) * Pilot Holder

68) W840470 Pilot Assembly Gasket

79) 433-525 Burner Assy - NG/LP

82) 433-024 Burner Grate Assembly - NG/LP

83) * Rear Log Support Bracket - NG/LP

85) 431-930 Log Set

86) 430-097 Air Deﬂ ector-Left

87) 433-018 Air Deﬂ ector-Right

*Not available as a replacement part.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

PARTS LIST

Flush Front & Louvers

Part # Description Part # Description

117) 904-196 Magnet - 1' round

130) 430-924 Flush Glass Trim (set) - Gold (Option)

131) 430-926 Flush Glass Trim (set) - Brass (Option) 430-947 Flush Glass Trim (set) - Brushed Steel (Option)

430-918 Flush Louvers (set) - Gold/Black (Option) 430-920 Flush Louvers (set) - Brass/Black (Option) 430-922 Flush Louvers (set) - Black (Option) 430-923 Flush Louvers (set) - Black/Steel (Option)

133) * Flush Louver Assy-Top 430-162 Front Deﬂ ector

134) * Flush Louver Assy-Bottom

433-538 Flush Door Assembly Complete

135) 940-088/P Glass (Flush)

137) 904-691 U-Clip

139) 936-155 Glass Gasket (Tadpole)

140) 948-042 Spring Hinge - Black

430-940 Finishing Trim (Set) - Black (Option) 430-942 Finishing Trim (Set) - Brass (Option)

157) * Finishing Trim Left

159) * Finishing Trim Right

158) * Finishing Trim Top

431-943 Double Screen Door Complete (Option)

171) * Door Frame Left Assembly

172) * Door Frame Right Assembly

173) 904-712 U-Clip for Frame

174) 430-133 Door Handle

175) 511-084 Door Latch

178) * Door Support Frame Assembly 904-715 Pushnut Fastener 3/16" * Screw - #8 x 1/2"

179) 948-216 Regency Logo Plate

*Not available as a replacement part.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Bay Front & Louvers

Part # Description

430-930 Bay Front Complete

106) 940-079/P Side Glass

107) 936-243 Glass Gasket

108) 940-078/P Center Glass

110) * Bay Door Frame

111) 902-322 Bay Brick Panel - Standard 432-905 Bay Brick Panel - Standard Brown 432-906 Bay Brick Panel - Standard Red

112) * Bay Brick Panel Spacer

117) 904-196 Magnet (1" round)

118) * Louver Hold Down

120) 400-189 Glass Retainer

432-956 Bay Door Trim (set) - Gold 432-954 Bay Door Trim (set) - Brass 432-958 Bay Door Trim (set) - Brushed Steel

123) * Bay Door Trim (each) - Black

430-932 Bay Louvers (set) - Gold/Black 430-934 Bay Louvers (set) - Brass/Black 430-936 Bay Louvers (set) - Black 430-937 Bay Louvers (set) - Steel/Black

125) * Bay Louver Assy-Top 433-026 Bay Door Deﬂ ector

126) * Bay Louver Assy-Bottom

129) 948-042 Hinge

130) 432-960 Bay Front Screen

131) 948-216 Regency Logo Plate

PARTS LIST

*Not available as a replacement part.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

NOTES

___________________________________________________

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

WARRANTY

Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a Regency Product. This warranty is not transferable.

The Warranty: Limited Lifetime

The combustion chamber, heat exchanger, burner tubes/pans, logs, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime Warranty for ﬁ ve (5) years for parts and subsidized labour* and parts only thereafter.

Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for ﬁ ve (5) years and parts only thereafter from date of purchase.

External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date of purchase and parts only thereafter.

Special Finishes - One year on brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating and cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks, ie. ﬁ nger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.

Electrical and mechanical components such as blowers, switches, wiring, thermodiscs, FPI remote controls, spill switches, thermopiles, thermocouples, pilot assembly components, and gas valves are covered for one year parts and subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and continue as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.

FPI venting components are covered parts and subsidized labour* for three (3) years from date of purchase.

Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.

Conditions:

Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.

Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of installation. Reported damage after this time will be subject to rejection.

It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect.

The authorized selling dealer is responsible for all in-ﬁ eld service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers.

At all times FPI reserves the right to inspect product in the ﬁ eld which is claimed to be defective.

All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name, purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.

Exclusions:

This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.

At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured. ie. as products evolve, ﬁ eld modiﬁ cations or upgrades will not be performed.

FPI will not be liable for travel costs for service work.

Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.

Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.

Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.

The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical systems such as furnaces, fans, clothes dryer, etc.

Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.

FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.

Performance problems due to operator error will not be covered by this warranty policy.

Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from Regency, may nullify your warranty on this product.

Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.

* Subsidy according to job scale as predetermined by FPI.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Regency ﬁ replace products are designed

with reliability and simplicity in mind.

In addition, our internal Quality Assurance

Team carefully inspects each unit

thoroughly before it leaves our

door.

Fireplace Products International

Ltd. is pleased to extend this

Limited Lifetime Warranty to the

original purchaser of a Regency

Product.

See the inside back cover for details.

http://www.regency-ﬁ re.com

Installer: Please complete the following information

Dealer Name & Address: ______________________________________________

___________________________________________________________________

Installer: ___________________________________________________________

Phone #: ___________________________________________________________

Date Installed: ______________________________________________________

Serial No.: __________________________________________________________

Regency and Panorama are trademarks of FPI Fireplace Products International Ltd.

Printed in Canada

Regency P33-LP3, P33-NG3 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual