Reflections Saybrook, Titan, Solar Installation Instructions Manual

LED ILLUMINATED ALUMINIUM CABINETS

REFLECTIONS

DESIGNER LED MIRRORS

ELECTRICAL SAFETY INSTRUCTIONS

All connections must be installed by a licensed
electrician, in accordance with current building codes.
Consult a qualified electrician.

IMPORTANT

Always switch off the electrical supply at the main
during installation and maintenance. It is
recommended that the circuit breaker is switched off
for the necessary circuit before installation
commences.

Fitting in Bathrooms is subject to the appropriate
building code Regulations. This product is NOT
suitable for outside zones. It is also Not suitable for
installation in saunas, steam rooms or shower
cubicles. This product is only suitable for permanent
installation. DO NOT connect to a trailing plug
and socket outlet. This product is only suitable for
indoor use. Do not attach the product to surfaces that
are damp or otherwise electrically conductive.

INSTALLATION CARE & SAFETY

Wear suitable eye protection when drilling. Take care
when using power tools. Beware of hidden cables or
pipes. Take care if drilling on tiled surfaces in case the
drill slips. A piece of masking tape applied to the wall
before marking out the fixing holes will stop the drill
from wandering.

by LTL

Saybrook

Installation Instructions

IMPORTANT

DO NOT strike glass
pointed items. DO NOT

cold items against or in
surfaces unless an

materal is used to prevent such items coming in
contact with the glass. The nominal thickness of the

mirror glass used in this product is 1/4” and is flm
backed for safety. If the glass becomes chipped or

broken replace immediately.

components with hard or

place very hot or very

close proximity to glass

adequately thick

insulation

It is recommended that the unit is cleaned with a soft, dry, non
abrasive cloth when turned off. Never use cleaning agents or
abrasive materials on any type of surface finish. Do not allow
moisture to come into contact with the electrical components.

1-800-360-1585 • fax [phone] • [e-mail]

CLEANING

125 Rt. 61 Schuylkill Haven, PA 17972

www.ltlhomeproducts.com

LED ILLUMINATED ALUMINIUM CABINETS

Installation Instructions

Saybrook

Diagram A

Diagram C

1. Remove the packaging taking special care with the
and remove the screws on the doors. Take care not to

Measure the length,width,depth of back of cabinet for recess ( see diagram A )

2.

Release the hinges by pressing the bottom of hinges to remove the doors ( see diagram B )

3.

Open the electronic cover to fix the screws after cabinet installed on proper position. ( See Diagram C )

4.

Install the cabinet door after screws fixed. Make sure the hinge hook was fully inserted into the holes ( see diagram D-1 )

5.

Press the hinge body to be fixed with hinge base ( see diagram D-2)

6. Before making

a supply cable already
Connections should

requires an

any electrical con

fitted. This cable should be ftted to the household lighting

be made in accordance with the latest regulations.

earth connection.

nections it is necessary to turn off

doors and separate shelves. Open the cabinet doors

Diagram B

Diagram D

lose the screws.

the main electricity sup

D-1

D-2

D-2

ply. This unit is provided with

circuit or to a fused

cabinet is manufactured to CLASS 1 and

This

3 AMP supply.

B

7. When the cabinet is fully secure the internal top cover

removed earlier. When the cover is closed and secure
the shaver socket. If the light fails to function properly it is likely

or reflective surface

OPERATING INSTRUCTIONS

Light can be controlled by using the 3-way rocker under the cover
of cabinet inside to control warm-off-cold of lighting

should be closed and secured with the small screws

restore the

the IR sensor has been positioned too close to an adjacent wall

1-800-360-1585 • fax [phone] • [e-mail]

main power and test the function of the lights and

125 Rt. 61 Schuylkill Haven, PA 17972

www.ltlhomeproducts.com

LED ILLUMINATED ALUMINIUM CABINETS

Release Lever

r

Release Lever

Installation Instructions

Saybrook

Fitting the glass shelves.

8.

Firstly insert a shelf into the
top two shelf support brack­ets then slide upwards so the
grub screws on the under­side of the support brackets
(Screw C) can be sufficiently
tightened to hold glass in
place. Repeat for the bottom
shelf (NOTE: be careful not

to overtighten). Shelves can
be positioned accordingly by sliding the supports up or
down (NOTE: Take care to use both hands when sliding
shelves and ensure thatsupport brackets at both ends
slide simultaneously).

C

If the doors are out of alignment first remove the soft-

9.

close buffer (from the relevant hinges) which clips into
the main hinge plate. The soft-close hinges offer
adjustment in 3 directions via adjustment screws

and E (see diagram).

D

D

E

125 Rt. 61 Schuylkill Haven, PA 17972

1-800-360-1585 • fax [phone] • [e-mail]

www.ltlhomeproducts.com

REFLECTIONS

by LTL

DESIGNER LED MIRRORS

Installation Instructions:

LED ILLUMINATED ALUMINIUM CABINETS

Installation Instructions

-220 240V AC

Mains Supply

The next step is to make the electrical connection from the mirror to the

mains supply. Use the connection wire found at the rear of the mirror to make the
necessary connections. A second

electrical connections are

THIS PRODUCT IS MANUFACTURED TO CLASS I

CATEGORY AND MUST HAVE AN EARTH CONNECTION.

COLOUR CODING:
L - Live = Black
N - Neutral =

- Earth = Green

White

made.

person will need to hold the mirror in place whilst

Strip wires to a suitable
length. DO NOT connect
to a plug & socket outlet.

! IF IN DOUBT CONSULT YOUR ELECTRICIAN !

125 Rt. 61 Schuylkill Haven, PA 17972

1-800-360-1585 • fax [phone] • [e-mail]

www.ltlhomeproducts.com