Reflecta x4-scan User Manual

-0-

EN

Table of Content s

1. Precaution .................................................................2

2. Preparation................................................................5

z S tandard Accessories.....................................5

z Part Names.....................................................6

z Installing the Battery Pack..............................8

z Charging the Battery Pack………………........9

3. Place Film/ Slide Into The Holder............................ 11

4. Using the reflecta x4-S can......................................12

5. Playback Mode........................................................18

6. Delete Mode............................................................19

7. To Link the Card to Computer..................................21

8. Edit the Pictures.......................................................24

9. Appendix………………………..……………...………31

z Specifications................................................31

z Icon & Indicators...........................................32

z System Requirements...................................33

-1-

-2-

Welcome

Thank you for purchasing a reflect a x4-Scan.
Please take a moment to read through t his manual. Its
contents will send you on an educational journey into your
recorder multiple capabilities.

1. Precaution

Before using reflecta x4-Scan, please ensure that you
read and understand the safety precautions d escribed
below. Always ensure that the reflecta x4-Scan is
operated correctly.

• Never operate reflecta x4-Scan inside of an aircraft
or anywhere else wh ere operation of such d evices i s
restricted. Improper use creates the risk of serious
accident.

• Do not try to open the case of reflecta x4-Scan or
attempt to modify reflecta x4-Scan in any way.
High-voltage internal components create the risk of
electric shock when exposed. Maintenance and
repairs should be performed only by authorized
service providers.

• Keep reflecta x4-Scan away from water and other
liquids. Do not use reflecta x4-Scan with wet hands.
Never use reflecta x4-Scan in the rain or snow.
Moisture creates the danger of fire and electri c
shock.

• Keep reflecta x4-Scan and its accessories out of the
reach of children and animals to prevent accidents
or damage to the reflecta x4-Scan.

If you notice smoke or a strange odor coming from
reflecta x4-Scan, turn the power off immediately. Take
reflecta x4-Scan to the nearest authorized service
center for repair. Never attempt to repair reflecta
x4-Scan on your own.

EN

• Use only the recommended power accessories. Use
of power sources not expressly recommended for
reflecta x4-Scan may lead to overheating, distortion
of the equipment, fire, electrical shock or other
hazards.

• reflecta x4-Scan may become slightly warm during
use. This does not indicate malfunction.

• If the exterior of reflecta x4-Scan needs cleaning,
wipe it with a soft, dry cloth.

-3-

-4-

FCC Notice

This equipment has been tested and fou nd to comply with
the limits for a Class B Digitize device, p ursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interfere nce in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy. If not installed
and used in accordance with the instruction, it may cause
harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment on the off,
the user is encouraged to try to correct the interference by
one or more the following suggestion.

z Reorient or relocate the receiving antenna.
z Increase the distance between the equipment and

the receiver.

z Connect the equipment to a different power outlet

other than the one where the receiver is connected.

z Consult an experienced television or radi o

technician for help.

CAUTION

To comply with the limits for a Class B Digitize device,
pursuant to Part 15 of the FCC Rules, this device must
only be installed on comput er equipment certified to
comply with the Class B limits.

-5-

2. Preparation

EN

St andard Accessories

reflecta x4-Scan QOG CD

Slide Holder Negative Holder

Clean brush USB cable

Adaptor Lithium Battery

(Optional)

Part Names

-6-

-7-

EN

Note: We suggest using bundled brush to insert into the reflecta

x4-Scan slot and clean the glass surface periodically to produce
a clear image. Please make sure your film negatives/ mounted
slides and cover trays are clean before inserting into the reflecta
x4-Scan as well. Dust or dirt from the negatives and cover trays
will affect the quality of your scanned images.

Installing the Battery Pack

1. Open the battery compartment cover by lightly
pressing and sliding it back as shown.

2. Insert the supplied battery. Make sure the battery
label is facing upwards and the (+ and -) ends of the
battery match to the polarities indicated in the battery
compartment.

3. Snap the cover back into place.

Battery power status

-8-

Charging the Battery Pack

EN

The battery pack is not charged at the time of purchase
and therefore needs to be charged before use. If the
battery charge becomes low while you are using the
copier, it is recommended to recharge it as soon as
possible.

1. Insert the battery pack into the battery compartment
(see page 8)

2. You may charge the battery in 2 ways:

(a) Plug the USB mini B of the supplied USB cable to

the USB port of the copier, and plug the other USB
end into the USB port of your computer/notebook.

Please charge the battery at least 5.5~6 hours

prior to your first use.

-9-

(b) Plug the USB mini B of the supplied AC adaptor

(optional) to the USB port of the copier, and plug
the adaptor to the power outlet.

Please charge the battery at least 2.5~3 hours

3. Red LED will light on during charging. When the
battery pack is fully charged, the red LED light will be
off and you may disconnect the charging conne ctions.

Status LED:
Red: The Image Copier is OFF, the battery is charging.
Purple: The Image Copier is ON, the battery is charged

simultaneously.

Blue: The Image Copier is ON, the battery is not charged

or no battery is loaded.

-10-