Reflecta CyberView X5 SF User guide

1

Manual

X5 SF

ENGLISH

ENGLISH

CyberView

User’s

X5 SF
Manual

1

3

2

TABLE OF CONTENTS

FEDERAL COMMUNICATIONS COMMISSION

FEDERAL COMMUNICATIONS COMMISSION

FCC STATEMENT

•

•

•

•

FCC STATEMENT

TABLE OF CONTENTS

This Equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency

ENGLISH

energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

Warning :

Use only shielded signal cables to connect I/O devices to this equipment.
You are cautioned that changes or modi cations not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit di erent fromwhich

the receiver is connected to.

• Consult the dealer or an experienced radio/TV technician for help.

Getting Started 4
Quick Installation Guide (QIG) 5

Installing Software and Driver 6
Installing Hardware 8
Additional Features 8
Loading the  lm/slides into the Holders 9
One Button Scan 11
How to Scan Slides 12
STEP 1 - Aquire Driver 12
STEP 2- Select Film Type 12
STEP 3 - Optional Prescan 12
STEP 4 - Set Scan Settings 13
STEP 5 - Set Scan Preferences 14
STEP 6 - Scan 17
STEP 7 - Exit 17
User Interface 18
I Main Window Area 18
II Preview Window Area 20
III Scan Setting Area 25
Technical Support 26

ENGLISH

2

3

5

4

Check the package content before getting started.

•

•

•

•

•

•

•

•

•

GETTING STARTED

•

•

•

•

For Quick Installation please refer to Quick Installation Guide. (Ref. Pg. 9)

ENGLISH

Package Contents

NOTE:

GENERAL GUIDANCE:

4

GETTING STARTED

Important! Save the original box, receipt and packing material for future
shipping needs.

• Slide Scanner.

• Film Holder (Where Applicable)

• Power Adapter [FAIRWAY Model No. : WRG 15F-120A]

Warning! Using any other power adapter may severely damage the scan­ner and will void the product warranty.

• Power Cord.

• USB 2.0 Cable.

• CyberView X5 Driver.

• Application software DVD.

• Printed User’s Manual.

• Application software means the imaging software such as Adobe®

Photoshop® Elements, this is subject to change without notice.

• Only use the supplied USB-Cable. Connect the computer to the scanner

directly using the USB 2.0 cable.

• Do not use a hub or extension cable. Only use the USB ports on the rear

of desktop computers.

• If there are any other devices (multifunction device, printers, scanners,

webcam) connected to the computer through USB, disconnect them.

• A minimum of 1GB RAM (Win/Mac) is required.

Operating Ambient Temperature Range

50º to 104ºF (10º to 40ºC)

Note: Do not turn on the scanner unless it is within this range. If the

scanner has been stored or transported outside of this range,
allow it to return
to within this range before turning it on.

Operating Ambient Humidity Range 15% to 76% rela-

tive

humidity (non-condensing)

Note: If the scanner is stored or to be transported in cold temperature

and then brought into a warm / humid environment
condensation may occur.

This device is designed solely for private use and is not intended for commer­cialuse. The warranty is reduced from 2 years to 1 year if errors or defects aris­ing from inappropriate use, improper operation or stress occur. The guarantee
period of the device for private use is 2 years or 20,000 scans.

ENGLISH

5

7

6

INSTALLING SOFTWARE AND DRIVER

QUICK INSTALLATION GUIDE QIG

for PC (Windows) User

WINDOWS SYSTEMS INSTALLATION DURING DRIVER INSTALLATION A WARNING
DIALOGUE BOX MAY APPEAR, IF THIS IS THE CASE PLEASE SELECT “INSTALL THIS
DRIVER ANYWAYS”.

ENGLISH

You may install the scanner driver directly if you have already installed TWAIN
compliant application software in your computer. Mac users can use iPhoto for
editing.

Notice:

NOTE: Not all PC’s will display the found new hardware window, some will install
in the background

QUICK INSTALLATION GUIDE QIG

Be sure to install the Application Software BEFORE installing the scanner
driver CyberView X 5.0.

1. In “Found New Hardware Wizard” window, select “Search automatically
or Browse computer for driver software.”

2. In “Completing the Found New Hardware Wizard” window, click
“Finish”.

TWAIN scanner plug-in Installation Guide for Adobe Photoshop Elements 9
and newer versions

The TWAIN scanner plug-in is no longer installed with Photoshop Elements 9.
In order to be able to import scanner device through Adobe Photoshop ele­ments, please follow below instructions after installing Adobe Photoshop
Elements 9 to  nd where and how to install the TWAIN component which was
previously installed with the application for versions earlier than Photoshop
Elements 9.

Important: Do not move plug-ins from previous versions of Photoshop Elements
into the Photoshop Elements 9 > Plug-Ins folder, or set the Photoshop Elements
8 (or earlier) > Plug-In folder as the Additional Plug-Ins Folder in Preferences.

Find complete information at o cial Adobe website:
http://kb2.adobe.com/cps/849/cpsid_84933.html

Macintosh

To install the legacy TWAIN plug-in for Macintosh, copy TWAIN.plugin folder
from: //Applications/Adobe Photoshop Elements 9/Optional Plug-Ins/Import­Modules/

Into: //Applications/Adobe Photoshop Elements 9/Locales/<locale>/Plug-Ins/

ENGLISH

INSTALLING SOFTWARE AND DRIVER

Before Installing the Scanner Driver...
If you choose to use the provided application for image editing, install the ap­plication software (ex: Adobe® Photoshop® Elements) by inserting the applica­tion CD into the computer’s CD/DVD drive. Follow the instructions that will be
displayed in a window that opens automatically.

Installing Scanner Driver

a. Insert insert driver CD into the computer CD/DVD drive and explore the

contents.

b. Double click the ”CyberView X 5.0” icon to begin the installation process.

Follow the onscreen prompts to complete the installation process.
NOTE: Make sure the scanner is NOT connected to the computer during the Cyber-

View X 5.0 driver installation.

c. Restart computer once the installation process is complete.

Please Note:

another USB Flatbed scanner or All-in-one Scan/Copier/Printer device installed, it may be
necessary for you to disconnect the other scanner from the USB port for the Film scanner to
work properly,

When installing your new scanner onto a Windows system that already has

6

Windows

To install the legacy TWAIN plug-in for Windows, copy twain_32.8ba from:
C:\Program Files\Adobe\Photoshop Elements 9\Optional Plug-Ins\Import­Export\

Into: C:\Program Files\Adobe\Photoshop Elements 9\Locales\<locale>\Plug-Ins\
Import-Export\

64-bit Windows

Photoshop Elements 9 is a 32-bit application. When installed on a 64-bit version
of Windows the path is slightly modi ed.

To install the legacy TWAIN plug-in for Windows, copy twain_32.8ba from:
C:\Program Files (x86)\Adobe\Photoshop Elements 9\Optional Plug-Ins\Import­Export\

Into: C:\Program Files (x86)\Adobe\Photoshop Elements 9\Locales\<locale>\
Plug-Ins\Import-Export\

7

9

8

Installing Hardware

ENGLISH

CrystalScan 7200

ProScan 7200

a. Connect the slide scanner to a power source.

1. Locate the power switch on the lower left side of the scanner. Make
sure the scanner is TURNED OFF.

2. Plug the AC adapter into an AC power source
FIRST before plugging it into the scanner.

3. Attach the USB cable to the computer using the stadard USB adapter
end. Attach the USB adapter end of the cable to back panel of the
scanner.

Additional features

1. Lid.

2. Slide Holder

3. Film Deck

4. One Button Scan

5. Release Switch

6. Viewing Window.

1. Scanner

2. Slide holder

3. Film Holder

4. One Button Scan

5. Back of the unit

6. Viewing Window

1. DC In

2. USB Port

3. Power Switch

To Scan Film (Film & Mounted Slides) CrystalScan 7200
Mounted Slides

1. Open Scanner Lid (1).

2. Release the Slide/Film Holder (5) put in slide “Shiny side up” then close
slide holder.

3. Close Scanner Lid (1) (optional).

4. Ready to scan.

Filmstrips

1. Open the scanner lid (1).

2. Release the Slide Holder (5).

3. Position the  lm that you wish to scan in the center of the viewing
window (6).

4. Push down the  lm frame and close the slide holder.

5. Ready to scan.

ProScan7200

ENGLISH

To Scan Mounted Slides

1. Mounted Slides
1-1. Load the mounted slides into the slide holder, shiny side facing upward
1-2. Insert the slide holder into the scanner with the arrow facing upwards
1-3. Insert to holder into the scanner from the left or the right side

8

9

11

10

ProScan 7200 - Scanning Slides (Continued....)

Please Note: improper insertion will
cut o the top of the image.

One Button Scan

1. Open the CyberView (see page 12 to acquire the CyberView driver program)

2. Con gure Scan Settings (see Page 13)

3. Select the Scan to directory,  le format (TIF or JPG, once con gured, Press the
scanner button ( ) to begin scanning.

ENGLISH

ENGLISH

To Scan Negative Film Strips
2-1. Load the negative into the holder making sure to align the  lm frames with the
frames on the holder, and with the shiny side facing upward

2-2 Close the  lm holder

2-3. Insert the  lm holder into the scanner from the left or right side, with the arrow
facing upwards

CrystalScan 7200
One Touch Button

NOTE:

If you do not open CyberViewX 5.0 FIRST, the scan button will not function.

ProScan 7200
One Touch Button

10

11

13

12

STEP 1 – Acquire Driver

HOW TO SCAN SLIDES

(For PC User)
Open CyberView X 5 from Start – All Programs –CyberView

(For MAC User)

ENGLISH

Open Macintosh Hard drive – Applications –CyberView

STEP 2 – Select Film Type

Select the  lm type to be scanned - Positive, Negative or B&W (Black and White).

Pre-Scanning should be used to manually adjust color/edit settings for each slide
before doing the  nal scan. It’s possible to set di erent settings for each slide to
be scanned.

12

HOW TO SCAN SLIDES

STEP 3 – Optional Prescan

Select the “Prescan Current Frame“ to prescan the slide currently loaded into
the scanner or “Prescan...“ to prescan slide or slides at speci c positions in the
magazine.

STEP 4 – Set Scan Settings

a. Resolution

The default scanning resolution is 1000dpi, additional resolution options
are listed below.

Notice: Higher scanning resolutions result in greater scanning time and hardisk

space requirements.

b. Color Depth

Choose between 8 and 16bit. A higher color depth setting will result in
a larger range of colors in the  nal scanned image.

The Film Scanner colour depth is 48 bit true color. The scanning software has
the capability of selecting 8 bit color mode or 16 bit color mode when scanning,
This will produce 24 or 48 bit color images, 8 bits or 16 bits per Red, Green and
Blue color channels.

Example:

8 bit mode = 8 Red, 8 Green, and 8 Blue for a total of 24 bit color
16 bit mode = 16 Red, 16 Green, and 16 Blue for a total of 48 bit color

NOTE: Make sure there is enough space available

on the computer when changing the Scanning
Resolution. A high scanning resolution results in
large  les that may prove di cult to save.

Color image  le size of di erent resolutions
and color depths:

Scanning

Resolution

300dpi 8 bit 24-bit ~350Kb

600dpi 8 bit 24-bit ~1MB

1800dpi 8 bit 24-bit ~12MB

3600dpi 8 bit 24-bit ~52MB

7200dpi 8 bit 48-bit ~208MB

Scans include Auto Balance and Digtal Noise
Reduction on:
Processor: AMD 9650 Quad-Core 2.3GHz
Memory: 2GB
System type: Vista 64 bit

Scan Mode – Normal mode produces a scan in jpeg format while Quality pro­duces a non-compressed, “loss-less” TIFF image.

Color

Depth

(by RGB

channel)

Color
Mode

File Size

TIFF

(no compres-

sion)

ENGLISH

13

15

14

STEP 5 – Set Scan Preferences

Select Scan - Preference - Film Type - Scan Setting

ENGLISH

“Prescan Resolution“ - Default pre-scan resolution.

“Using default real scan resolution“ - Enables default scan
resolution setting.

“Color Depth“ – Default color depth while scanning.

“Scan Mode“ – Default scan mode while scanning.

Con guring Scan Preferences

1. Select Browse and choose the designated folder to save the scanned
image to

2. Enter the  le name.

Set Scan Preferences (Continued...)

4. Options - Use Film Index: Use the number assigned to the slide based on it’s
position in the cartridge.
User De ned Start Number: Enter a speci c start number

5. Choose the  le type , “TIF” or “JPG”. (TIF uncompressed or JPG Compressed­Choose image quality for JPEG. (20-100) 100 o ers the least amount of compres­sion

Advanced Setting - PC Users

Advanced Setting - Intel Mac Users

ENGLISH

3. Trailing Index after Base File Name Digits: De nes the length of the
 le name and numbering sequence up to 6 digits Example image1 or
image000001.

14

”Auto Exposure” - Attempts to  nd the correct exposure to get the wid­est range of whites and blacks while putting the middle grays at around
the middle of the data range.

”Auto Balance” - Using the image histogram to balance RGB channels. It
estimates images’ color cast and adjust the images accordingly

“Auto Contrast” - The scanner software analyzes the data and automati­cally adjusts the Setting for the White and Black Points.

”Digital Noise Reduction” – Applies a  lter, Reducing the  lm grain.

15

17

ENGLISH

16

Default Scanning Area

Adjust the scanning size as well as adjust the “Scan O set” setting to move
the image position of slide.

Auto Color takes the guesswork out of the scanning process to streamline the
work ow and achieve the best results. Proprietary color enhancement
technology is applied to scanned images to provide the most accurate color
adjustment, resulting in vibrant images with optimal brightness, contrast and
saturation.

ENGLISH

STEP 6 – Scan

Scan - Scan- Scan Current Frame

CS7200 - Windows and Mac PowerPC Users ONLY- Digital ICE, ROC, GEM

(for additional information, please see included Digital ICE

Intel Based Mac Users - Magic Touch / Auto Color

Enable / disable Magic Touch and Auto Color adjustment to scans.

Magic Touch is a powerful dust and scratch removal technology that does away
with the hassle of learning complex and tedious software techniques. Being
hardware-based, it works seamlessly with the scanning process to ensure the
best possible results when bringing images into the computer. Dust, scratches
and other  aws are intelligently detected and eliminated, restoring the image to
its original beauty.

Scanning with Magic Touch requires longer scanning times, the feature is turned
o by default.

3

Users guide)

16

This begins the scan to  le process

All scaned images will be saved to the directory location set previously,
the factory default locations are:

Windows: C:\Users\[YOUR NAME\Documents;
MAC: Mac HD\Users\[YOUR NAME]\Pictures\Cyberview Images),

STEP 7 – Exit

Select “Scan > Exit” to close the driver. Scanned image  les can be open/edited
with any image editing software.

If using the supplied image editor, for help with this application see the users Help

NOTE:

from within the application or browse the supplied DVD for the help documentation.

17

19

18

USER INTERFACE

USER INTERFACE

There are four major parts of theCyberView X 5 user interface:

I. Main Window Area
II. Preview Window Area [Fixed Window]
III. Scan Setting Area [Floating Window]

[Fixed Windows]

I. Main Window Area [Fixed Windows]

ENGLISH

ENGLISH

Menu Commands - Scan

Prescan - Prescan Current Frame: Pre-scan the existing slide.
Scan - Scan Current Frame > Scan the current slide.

Menu Commands - Preview

Zoom, Rotate & Flip features.

Revert

Discards all modi cations and restores the image back to the original
state.

Preference - See Scan Setting (See Page 13)

Exit

Closes the CyberView X5 user interface.
There is a message pop-up “Quit the application prompts to save docu­ments?“ click “Yes“ to save , “No“ to discard the current
settings or “Cancel“ to return to Cyber View X.

18

19

21

20

Menu Commands - Image Adjustment

ENGLISH

a. Image Adjustment

1. Variations: Generates di erent views of image with options to make changes
to highlights, midtones, etc.

2. Color Balance

To adjust the brightness, contrast, saturation, and color (CMY or RGB)
of the image. Comparisons between before and after adjusted images
are shown for reference.

ENGLISH

20

Example:

Balance” window to adjust the image by selecting the slider in the center and moving it to
the right. The image’s “After” view becomes lighter. Select “OK” to accept the changes which
will be sent to the scanning hardware. This can also be used to adjust each of the functions
in “Color Balance” by contrast, saturation and speci c color ranges of cyan, magenta and
yellow.

If a previewed image appears too dark, use the “Brightness” slider in the “Color

21

23

22

3. Curves and Levels

•

•

Menu Commands - Window

ENGLISH

Example:

Input slider in the Curves and Levels window can be made to correct the image. Selecting
the Gray slider in the center and moving it to the left will result in changes in the “After”
view resulting in a lighter image. Once the adjusted image is acceptble select “OK” to send
changes to the scanning hardware. The same method can also be used to adjust each color
channel independently, using the channel drop down menu “RGB = All colors” R = Red, G =
Green, and B = Blue.

Adjust image settings by moving Curve and Levels settings.
Comparison between before and after adjustment is displayed for
reference.

When the previewed image appears to be too dark, adjustments with the

1. Exposure Setting: To adjust the exposure time (R, G, B) press ”Reset” to restore to

the default setting.

Menu Commands - Help

• Update: Firmware: Upgrade the  rmware version, select the path where the  le of

 rmware has been saved. (These  les may be downloaded from our website)

• About: Displays system information (including operation system, CPU), product
information (including product name, model name, hardware version,  rmware ver­sion, software version, device information including interface and optical
resolution).

Function Bar Diagram

Please select your  lm type
and brand from the toolbar:

Negative
Positive (also
known as Slide)
Black and White

II. Preview Window Area [Fixed Windows]

ENGLISH

22

Prescan: Pre-scan the current  lm, press drop down for more options.

Scan: Scan  lm, press drop down button for more options.

Image Adjustment: Press drop down button for more options.

23

25

24

Status Line

In the lower left hand corner, the color level (RGB: red, green, blue) and
coordinates of the location [ex: I] are displayed. The zoom scale, the current slide
magazine location and how many areas selected to scan (2 or or higher indicates:
Multiple scan areas on one slide [ex: II].

I.

ENGLISH

ENGLISH

Preview the image you pre-scan, you can select the measurement unit “in“-“cm“­“px“ by clicking the upper-left corner.

Toolbar Diagram

Select scan area: more than one selection can be made at a time.

Zoom In: To magnify the image where the cursor is currently located.

The image will be magni ed with every click until the maximum multi­ple (1000%) is reached.

Zoom Out: To reduce the size of the viewed image click the Zoom Out
cursor to the desired area, the image will reduce by half with every click
until the lowest multiple (25%) is reached.

Rotate 90 Left: To rotate the image counter clockwise 90 degrees.

Rotate 90 Right: To rotate the image clockwise 90 degrees.

Flip Horizontal: To Flip the image 180 degrees horizontally.

Flip Vertical: To Flip the image 180 degrees vertically.

II.

III. Scan Setting Area [Floating Windows]

Normal mode [ex: I] to input the basic parameter to scan (including scan
resolution,  lm size, color depth).

Advanced mode [ex: II] to input the parameter of scan output, scan resolution,
and color depth

II.

I.

24

Revert: Discard all modi cations and restores the image back to
the original state in preview windows.

25

26

TECHNICAL SUPPORT

TECHNICAL SUPPORT

CyberView

For information regarding the  lm scanner and CyberView driver, please visit
www.re ecta.de.

ENGLISH

Bundled application software

You can refer to the HELP function on the application menu bar or visit the soft­ware company’s website.

**This user manual has also been archived in the packaged CD.

26