Reese 44152 User Manual
Equipment Required:
Form: F205 Rev A 5
-6-
05
Fastener Kit: 01130-545
Wrenches: 13mm, 19mm, 3/4, 7/8
Drill Bits: 1/2”
Bumper
bracket
Frame
Installation Instructions
Nissan Pathfinder (4WD)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Manufacturer’s Rating or
Max Gross
Trailer WT (LB)
Part Numbers:
75020
44152
87482
Max Tongue
WT (LB)
500 (227 Kg)5000 (2270 Kg)
350 (159 Kg)3500 (1589 Kg)
4
Compress bend if
additional exhaust
clearance is required
1111
2222
3333
4444
5555
3
Bolt 1/2-13 X 1.50Qty. (2)
SpacerQty. (2)
Lock Washer 1/2Qty. (6)
Hex Nut 1/2-13Qty. (4)
Bolt M12 X 1.25 X 35Qty. (2)
Detail “A”
6
9
8
9
Side
bracket
Detail “B”
Exhaust
isolator
Wiring Access Location: SUV1, SUV2
Frame
Exhaust
isolator
3
5
Bracket to
be removed
6666
7777
8888
9999
Nut M8 X 1.25 Qty. (2)
Wire Nut SpacerQty. (2)
Lock Washer 5/16Qty. (2)
Flat Washer 5/16Qty. (4)
Bolt 1/2-13 X 1.25Qty. (2)
1
2
7
Bumper
bracket
License plate
bracket
Figure 1.
3
4
1. Remove bracket from each side of vehicle frame as shown in Figure 1. Save brackets and fasteners for reinstallation if the receiver is removed
2. Remove exhaust system isolator and discard 8mm nuts. Allow exhaust to drop.
3. Lift receiver into position. Install 1/2" hex bolt, lock washer and nut through side bracket and bumper bracket as shown in Detail “A".
4. Install 1/2" hex bolt, spacer, lock washer and nut through bottom of frame as shown in Figure 1.
5. Using the hitch as a template, enlarge the forward hole visible through the bracket with a 1/2" drill bit.
6. Insert wire nut spacer through opening in rear of vehicle frame and slide spacer over 1/2" hole drilled in step 5.
7. While holding nut spacer in place, install M12 hex bolt and lock washer through side bracket and into nut block as shown in Figure 1.
8. Assemble two (2) 5/16" flat washers and one (1) 5/16" lock washer to each end of exhaust isolator, as shown in Detail “B" and reinstall using
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
1991, 2003, 2006 Cequent Towing Products
from the vehicle.
Note: Bolt heads must be to inside of frame.
Note: Keep nut spacer along outboard edge of frame and make sure spacer is flat on surface of frame c-section.
8mm hex nuts provided. If additional exhaust clearance is required, bend metal portion of isolator as indicated by arrows.
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M12 CL 8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Rev. D11/26/07N75020Sheet 1 of 1
Loading...