Reely Unbreakable foam FPV paper plane kit User manual
Installation and operating instructions
Unbreakable foam FPV paper plane kit
Item no. 1590614
Intended use
This product is a model aircraft. It is suitable for outdoor use and designed for model aircraft
beginners.
You can install compatible electrical drive and control components in the model. These are not
included with the product. A sample conguration of optional components is provided in the
instructions. However, the actual conguration may vary depending on the components used.
Please refer to the technical data when purchasing optional components.
Read the assembly and operating instructions carefully and store them in a safe place.
Make this product available to third parties only together with its operating instructions. This
product complies with statutory national and European regulations. All company and product
names are trademarks of their respective owners. All rights reserved.
Download the latest instructions at www.conrad.com/downloads or scan the
QR code on this page. Follow the instructions on the website.
Symbols
The symbol with the exclamation mark in the triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the
product.
1. All parts.
2. Assemble the motor seat rst. Glue
the motor seat in the corresponding
position.
Assemble according to the picture.
3. Glue the fuselage. Apply glue to
the corresponding adhesive part of
the fuselage. Apply glue and wait
3 minutes to cure and then stick
together.
Assemble as shown in the picture below.
Safety instructions
The product is not suitable for children under 14 years of age.
Read the instructions and safety information carefully. If you do not follow the
safety instructions and information on proper handling in this manual, we will
assume no liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
You are solely responsible for the safe operation of this model!
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave the packaging lying around carelessly, as it may become dangerous playing
material for children. Keep small parts out of the reach of children!
• When assembling the model, take care not to injure yourself on sharp edges or pointed ends.
• This model has the potential to cause damage to property and/or individuals. Make sure that
you are sufciently insured, e.g. by taking out private liability insurance. If you already have
such a policy, check with your insurance company that the use of this model is covered by the
policy. In some EU countries, you are required to have insurance when using a model aircraft.
• The product must not become damp or wet.
• Improper use can cause serious damage to people and property! Ensure that you maintain a
sufcient distance from peoples, animals and objects.
• Select a suitable location to y the model aircraft.
• Only y the model when you are fully alert and able to respond. Fatigue, alcohol and medication
can can affect your ability to respond.
• Do not direct the model towards spectators or towards yourself.
• Please refer to the manufacturer‘s safety and installation instructions when installing electrical
components.
If you have questions which remain unanswered by these instructions, contact our
technical support service or other technical personnel.
4. Assemble the supporting carbon rod.
First, the two carbon tubes are inserted
into the hole from the back and then
the corresponding hole in the motor
seat is inserted, as shown in the
picture.
And then put the square carbon bar on
the back from the front.
The motor seat must be in the middle
position and then xed with glue.
The back side carbon rod should be
assembled into the slot. After determining
the position, glue the bottom of the
square carbon rod and the inside of the
slot.
Assemble the triangular reinforcement
head plate. Apply glue to the triangular
reinforcing plate.
Disposal
Always dispose of the product according to the relevant statutory regulations.
You thus fulll your statutory obligations and contribute to the protection of the environment.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopy, microlming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1590614_v1_0817_02_DS_m_gb_(1)
5. Stick to the side of the fuselage
to reinforce the carbon chip. After
measuring the size, cut the carbon
slice with the scissors. Apply glue
evenly to the side of the fuselage and
the carbon sheet.
Done.
Assemble the ctrl horn and fast adjust
screw.
6. Assemble the z-bend push rod. Glue
the servo in the hole.
7. Pass the servo wire from the front
through the carbon hole.
8. Add the extension wire.
Solder the motor, ESC and JST
extension wire.
Recommended electronics (optional):
• Motor: 2815 (2207) 1450 kv
• Servo: 9 g * 2
• Esc: 12 A and 2A bec
• Prop: 0947
• Battery: 2s 1500 mah-2200 mah
Use the screw assembly motor to the
wood seat.
Collate wiring harness.
Put the 3s 1300 mAh battery on the
triangular head using 3m sticker.
Technical Data
Weight .......................................... 280 g
Wing span ..................................... 100 cm
Material ......................................... 5 mm PP
Loading...