Reely SU27 User guide
Installation and operating instructions
Unbreakable foam model aircraft (SU27)
Item no. 1590610
Intended use
This product is a model aircraft. It is suitable for outdoor use and designed for model aircraft beginners.
You can install compatible electrical drive and control components in the model. These are not included with
the product. A sample conguration of optional components is provided in the instructions. However, the
actual conguration may vary depending on the components used. Please refer to the technical data when
purchasing optional components.
Read the assembly and operating instructions carefully and store them in a safe place.
Make this product available to third parties only together with its operating instructions. This product complies
with statutory national and European regulations. All company and product names are trademarks of their
respective owners. All rights reserved.
Download the latest instructions at www.conrad.com/downloads or scan the QR code on
this page. Follow the instructions on the website.
Symbols
The symbol with the exclamation mark in the triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the product.
Safety instructions
1. All parts.
2. Assemble the airplane head. Glue the
two pieces. Glue evenly then wait for
3 minutes.
After gluing,the following picture will be
seen.
3. Install the support carbon rod, glue
the carbon rod groove and the square
carbon rod evenly, and then glue.
4. Glue the head of the airplane, glue the
top of the airplane head evenly, and
put it in place for 3 minutes to x them.
5. Glue two side boards
The product is not suitable for children under 14 years of age.
Read the instructions and safety information carefully. If you do not follow the safety
instructions and information on proper handling in this manual, we will assume no liability for
any resulting personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
You are solely responsible for the safe operation of this model!
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave the packaging lying around carelessly, as it may become dangerous playing
material for children. Keep small parts out of the reach of children!
• When assembling the model, take care not to injure yourself on sharp edges or pointed ends.
• This model has the potential to cause damage to property and/or individuals. Make sure that
you are sufciently insured, e.g. by taking out private liability insurance. If you already have
such a policy, check with your insurance company that the use of this model is covered by the
policy. In some EU countries, you are required to have insurance when using a model aircraft.
• The product must not become damp or wet.
• Improper use can cause serious damage to people and property! Ensure that you maintain a
sufcient distance from peoples, animals and objects.
• Select a suitable location to y the model aircraft.
• Only y the model when you are fully alert and able to respond. Fatigue, alcohol and medication
can can affect your ability to respond.
• Do not direct the model towards spectators or towards yourself.
• Please refer to the manufacturer‘s safety and installation instructions when installing electrical
components.
If you have questions which remain unanswered by these instructions, contact our
technical support service or other technical personnel.
Disposal
Always dispose of the product according to the relevant statutory regulations.
You thus fulll your statutory obligations and contribute to the protection of the environment.
After bonding, the following picture is
shown.
6. Glue the airplane head.
9. Glue the motor seat.
7. Glue the tail board.
8. Glue the bottom board.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopy, microlming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1590610_v1_0817_02_DS_m_gb_(1)
10. Glue two pieces of rudders. 11. Screw the motor to the wood part.
13. Glue them to the motor seat.
15. Push rods assembly
The push rod is made by connecting
1.5mm diameter carbon rod with
Z-shaped steel wire instead of push rod
linkage stopper.
Fix the Z-shaped wire and the carbon rod
with heat-shrink tubing. Make all of the
control rods needed in the same way.
16. You can assemble them using the
heat-shrink tubing. Then heat. At last
you can add some glue on it. It will
very strong.
12. Solder the motor and ESC, the joint
is insulated with a heat shrink tubing.
(solder)
Repeat that step the same way for the
left one.
14. Install the horn. There are 4 horns.
19. Push rods assembly
20. Fix all of the wires.
17. Install the servos, glue them on two
side of the airplane body, and the
servo wire will pass through the small
hole on the engine room side. (This is
the right servo here).
22. Jet SU27 The center of gravity is at
the red “x” on the wing.
You must setup your radio, select the
airplane mode to triangle Flywing.
18. Push rods assembly
Recommended electronics (optional):
• Motor: 1806 2300 kv
• Servo: 2x 9 g
• Esc: 12 A and 2 A bec
• Battery: 3s 400 mAh - 600 mAh
Technical Data
Weight .......................................... 95 g
Wing span ..................................... 65 cm
Material ......................................... 5 mm PP
21. Glue the 3M sticker for the battery
and the receiver.
v
Loading...