Page 1
Operating Instructions
Series TH5000 Spring Driven Hose Reels
Medium Pressure Model Numbers:
TH5400 OMP TH5425 OMP TH5400 OMPSW74
Dimensions
A 14 1/2”
A
D
Four 5/16” diameter mounting holes
INSTALLATION:
MOUNTING:
LUBRICATION:
B 13 1/2”
B
C
E
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.
Hose reel spring and bearings are factory lubricated and require no further lubrication.
C 9 3/4”
D 2 1/2”
E 6”
SAFETY
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
REPLACING HOSE:
ADJUSTMENTS:
REPAIRS:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Form# 1150-1003 Rev: 8/2018
Page 2
Series TH5000 Spring Driven Hose Reels
11
15
16
14
12
13
10
9
8
7
6
9
13
5
4
17
3
2
18
19
1
20
21
22
23
24
25
26
27
28
30
31
Item # Part # # Req. Description Item # Part # # Req. Description
1 S600996-1 1 Swivel Assembly 17 S500103 1 Spring Case & Hub Assembly
2 300031 2 1” Snap Ring 18 S82-15 1 10-32 x 3/8” Nyloc Nut
3 300034 2 Spacing Washer 19 S400021 1 Latch Bumper
4 S295-102 3 Self Tap Screw Plastite 20 S32-136 1 10-24 x 3/8” Screw
5 260022 1 Reel Sheave 21 S400012 1 Latch Bushing
6 500006 1 Reel Sheave Disk 22 S400018 1 Latch Spring
7 S500019 1 Latch Cam 23 300001 5 10-32 x 3/8” Mach. Screw
8 S260648 1 Spring Arbor 24 400020 1 O’Ring
9 300002 2 10-32 x 1/2” Machine Screw 25 S400109 1 Latch Plate Assembly
10 S500107 1 Guide Arm & Roller Assembly 26 300035 1 10-32 x 1” Machine Screw
12 500101 1 Base Assembly 27 1-117440 1 U-Bolt Hose Clamp
13 S300011 7 10-32 Hex Nut 28 300070 2 1/4-20 Nyloc Nut
14 S507287 1 Drive Spring Assembly 29 300039 2 Washer
15 S261360 1 Spring Case Stud 30 602306 1 Main Shaft
16 300006 1 3/8-16 x 1/2” Set Screw
Item # Description TH5400 OMP TH5425 OMP
11 Bumper Stop Assembly None 8-HR1004-3
31 Hose Assembly None 600669-3
-- Hose I.D. & Length None 1/4” x 25’
-- Reel Inlet Connection 1/4” F.P.T. 1/4” F.P.T.
-- Max. Operating Pressure 200 P.S.I. 200 P.S.I.
Parts common to
TH5400 OMPSW74 Reels
Item # Description # Req. Part #
5 Flange, Sheave 1 260022-40
6 Disc, Sheave 1 500006-40
10 Guide Arm Assembly 1 500107-39
12 Base Assembly 1 500101-39
17 Springcase Assembly 1 S500103-40
Page 2
www.reelcraft.com
Loading...