Page 1
Operating Instructions
Series TH5000 Spring Driven Hose Reels
Medium Pressure Model Numbers:
TH5400 OMP118 TH5425 OMP118
Dimensions
A 365 mm
A
D
Four 5/16” diameter mounting holes
INSTALLATION:
MOUNTING:
LUBRICATION:
B 356 mm
B
C
E
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.
Hose reel spring and bearings are factory lubricated and require no further lubrication.
C 248 mm
D 64 mm
E 156 mm
SAFETY
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
REPLACING HOSE:
ADJUSTMENTS:
REPAIRS:
Reelcraft International Inc. • Ph: +44 (0) 1536 406999 • Fax: +44 (0) 1536 406777
Unit 17 - Cronin Courtyard, Weldon South Industrial Estate, Corby - Northamptonshire NN18 8AG
europe@reelcraft.com • www.reelcraft.com/europe
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Form# R1150-1003 Rev: 1/2016
Page 2
Series TH5000 Spring Driven Hose Reels
11
15
16
14
12
13
10
9
8
7
6
9
13
5
4
17
3
2
18
19
1
20
21
22
23
24
25
26
27
28
30
31
Item
Part #
#
1 S600996-1 1 Swivel Assembly 14 S507287 1 Drive Spring Assembly 26 300035 1 10-32 x 1” Mach. Screw
2 300031 2 1” Snap Ring 15 S261360 1 Spring Case Stud 27 1-117440 1 U-Bolt Hose Clamp
3 300034 2 Spacing Washer 16 300006 1 3/8-16 x 1/2” Set Screw 28 300070 2 1/4-20 Nyloc Nut
4 S295-102 3 Self Tapp. Screw Plastite 17 S500103 1 Spring Case & Hub Assembly 29 300039 2 Washer
5 260022-35 1 Reel Sheave 18 S82-15 1 10-32 x 3/8” Nyloc Nut 30 602306 1 Main Shaft
6 500006-35 1 Reel Sheave Disk 19 S400021 1 Latch Bumper
7 S500019 1 Latch Cam 20 S32-136 1 10-24 x 3/8” Screw
8 S260648 1 Spring Arbor 21 S400012 1 Latch Bushing
9 300002 2 10-32 x 1/2” Mach. Screw 22 S400018 1 Latch Spring
10 S500107 1 Guide Arm & Roller Assembly 23 300001 5 10-32 x 3/8” Mach. Screw
12 500101 1 Base Assembly 24 400020 1 O’Ring
13 S300011 7 10-32 Hex Nut
#
Req.
Description
Item # Description TH5400 OMP118 TH5425 OMP118
Item
Part #
#
25 S400109 1 Latch Plate Assembly
11 Bumper Stop Assembly None 8-HR1004-3
31 Hose Assembly None 600669-3
-- Hose I.D. & Length None 1/4” x 8 m
-- Reel Inlet Connection 1/4” FPT 1/4” FPT
-- Max. Operating Pressure 207 bar 137 bar
#
Req.
Description
Item
Part #
#
#
Req.
Description
Page 2
www.reelcraft.com
Loading...