Page 1
Operating Instructions
Series 7000 Spring Driven Hose Reels
Low Pressure Model Numbers:
GC7535 OLP GC7925 OLP
Dimensions
A 20 1/4”
B 19 3/4”
C 7 13/16”
INSTALLATION:
MOUNTING:
LUBRICATION:
REPLACING HOSE:
D 3 7/8”
E 7”
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
Hose reel spring and bearings are factory lubricated and require no further lubrication.
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
ADJUSTMENTS:
REPAIRS:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Form# 1137-203 Rev: 4/2018
Page 2
Series 7000 Spring Driven Hose Reels
Item
Part #
#
1 5-117440 2 U-bolt 12 S600017 1 Guide Arm Assembly 20 S600016 1 Base Assembly
2 S260037 1 Drive Spring Assembly 13 300107 4 Lock Nut 21 S20-110 1 Machine Screw
3 S260031 1 Spring Case Stud 14 600830-10 1 Hose Assembly 23 S260069 1 Spring Case Gasket
4 S260074 1 Spring Case & Ratchet 15 S280-8 1 Hex Flange Nut 24 S600621 1 Spring Arbor & Key Assembly
5 S76-106 1 Hex Jam Nut 16 S82-15 10 Nyloc Nut 25 S260011 1 Sheave Assembly
6 300007 2 Snap Ring 17 S600018 1 Latch Pawl Assembly 26 600242 1 Swivel & Ell Assembly
7 260095-1 1 Main Shaft 18 S260067 1 Latch Spring 27 300070 4 Nyloc Nut
8 S35-84 1 Set Screw 19 S400012 1 Latch Bushing
Item # # Req. Description GC7535 OLP GC7925 OLP
9 1 Garden Hose Valve None 261447
10 1 Hose Assembly 601046-35 601044-25
11 1 Bumper Stop 600838 3-HR1004-3
#
Req.
Description
Page 2
Item
#
Part #
#
Req.
Description
Hose I.D. and Length 5/8” x 35’ 3/4” x 25’
Reel Inlet Connection 3/4” N.P.T. 3/4” N.P.T.
Max. Operating Pressure 200 P.S.I. 200 P.S.I.
Max. Operating Temperature 210 °F 210 °F
Item
#
Part #
#
Req.
GC7535 OLP GC7925 OLP
Description
www.reelcraft.com
Loading...