Reelcraft FE9000 User Manual

Operating Instructions

Series FE9000 Fuel Hose Reels

Low Pressure Model Numbers:

FE9200 OLP FE9300 OLP
FE9350 OLP FE9400 OLP
FE9450 OLP

Dimensions

B

F

C

INSTALLATION:

A 26 3/8”

B 26 1/4”

A

C 22 1/4”

D 7 3/4”

SAFETY

E 12”

E

F 24 1/8”

G 4 3/4”

D

G

The swivel union is packed separately in the reel carton, use teflon tape to assure a satisfactory seal. A flexible hose
connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and
binding. Non flexible connections will void the warranty, pressure rating of inlet hose must be equal to or more than
the pressure rating of the reel. Consult factory for proper spring when installing reels above 16 ft.

1. Do not use reel at higher pressures or temperatures than listed on the back
of this bulletin.

2. Remove all spring tension before beginning dissassembly process.

3. Reel spring motor case is permanently sealed. Any attempt to remove the
spring motor may cause serious injury.

LUBRICATION:

REPLACING HOSE:

ADJUSTMENTS:

REPAIRS:

MODIFICATION:

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [e-mail] • www.reelcraft.com

Hose reel spring and bearings are factory lubricated and require no further lubrication.

1. Wind spool flange clockwise-facing swivel-until spring is tight.

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to female outlet ell.

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.

Hose latching mechanism can be removed for constant tension applications.

Form# 613-193A Rev: 6/2013

Series FE9000 Fuel Hose Reels

11

10

9

8

7

6

5

4

3

3

2

1

12

13

37

14 15

36

6

1

38

16

17 9 1

3334

18 7 19

303132

20

4

21

22

23

2

24

25

26

27

28

29

6

39

40

41

3

42

43

6

3

44

Item

#

1 1/4-20 x 1/2” hex screw 16 S2-41 24 Latch pawl assembly 1 S600454
2 Side frame 2 270009 25 Latch spring 1 S260067-1
3 3/8-16 hex flange nut 12 S281-6 26 Latch bushing 1 S400012
4 Pillow block 2 S600416 27 10-32 x 7/8” screw 1 S20-110
5 End frame support 1 270012 28 Hose assembly 1 None
6 3/8-16 x 5/8” mach. screw 8 S44-2 29 Hose bumper assembly 1 None
7 3/8-16 x 1 3/4” screw 4 S44-8 30 Guide roller pin - long 2 S270016
8 Main shaft assembly 1 602377 31 Guide roller pin - short 2 S270015

9 Snap ring 6 S140-34 32 Guide roller 2 262436-5.468
10 Spring case assembly 1 600413-1 33 Guide roller 2 262436-2.968
11 Spring arbor 1 260888 34 Guide roller post 4 S270014
12 Spool assembly 1 600415 36 Hose guide roller plate 1 270011
13 Inlet tube 1 602364 37 5/16-18 x 1/2” hex screw 4 S2-51
14 Hose outlet support 1 270029 38 1/4-20 hex nut 8 S281-4
15 #10 x 3/8” self tap screw 1 S32-136 39 Guide roller plate SW 1 270045
16 Reducing bushing 1 300080 40 SW support bracket 1 270043
17 90° female NPT ell 1 270028 41 SW support bracket 1 270042
18 Latch ratchet 1 260889 42 Guide roller plate TW 1 270044
19 Swivel assembly 1 S600888-2 43 TW support bracket 1 270041
20 Reducing coupling 1 S289-5 44 TW support bracket 1 270040
21 1/2-20 hex flange nut 1 S280-8 -- Hose ID and length -- None
22 Latch bracket 1 260934 -- Working pressure -- 500 PSI
23 10-32 x 3/8” nyloc nut 1 S82-15 -- Max. temperature -- 210° F

Description

#

Req

FE9200 OLPBW

Item

#

Description

#

Req

FE9200 OLPBW

Page 2

www.reelcraft.com