Reelcraft FD9000 User Manual
Operating Instructions
Series FD9000 Fuel Hose Reels
Low Pressure Model Numbers:
FD9200 OLP FD9300 OLP
FD9350 OLP FD9400 OLP
FD9450 OLP
Dimensions
B
F
C
INSTALLATION:
A 26 3/8”
B 26 1/4”
A
C 22 1/4”
D 7 3/4”
SAFETY
E 12”
E
F 24 1/8”
G 4 3/4”
D
G
The swivel union is packed separately in the reel carton, use teflon tape to assure a satisfactory seal. A flexible hose
connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and
binding. Non flexible connections will void the warranty, pressure rating of inlet hose must be equal to or more than
the pressure rating of the reel. Consult factory for proper spring when installing reels above 16 ft.
1. Do not use reel at higher pressures or temperatures than listed on the back
of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
3. Reel spring motor case is permanently sealed. Any attempt to remove the
spring motor may cause serious injury.
LUBRICATION:
REPLACING HOSE:
ADJUSTMENTS:
REPAIRS:
MODIFICATION:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
Hose reel spring and bearings are factory lubricated and require no further lubrication.
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to female outlet ell.
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Hose latching mechanism can be removed for constant tension applications.
Form# 835-696A Rev: 6/2013
Series FD9000 Fuel Hose Reels
Item
#
1 1/4-20 x 1/2” hex screw 4 S2-41 26 Latch spring 1 S260067-1
2 Side frame 2 270009 27 Latch bushing 1 S400012
3 3/8-16 hex flange nut 12 S281-6 28 10-32 x 7/8” screw 1 S20-110
4 Pillow block 2 S270058 29 Hose assembly 1 None
5 End frame support 1 270012 30 Hose bumper 1 None
6 3/8-16 x 5/8” mach. screw 8 S44-2 31 Guide roller pin - long 2 S270016
7 3/8-16 x 1 3/4” screw 4 S44-8 32 Guide roller pin - short 2 S270015
8 Main shaft assembly 1 602314 33 Guide roller 2 262436-5.468
9 Snap ring 6 S140-31 34 Guide roller 2 262436-2.968
10 Spring & case assembly 1 S270105 35 Guide roller post 4 S270014
11 Spring arbor 1 S270002 37 Hose guide roller plate 1 270011
12 Sheave assembly 1 270107 38 5/16-18 x 1/2” hex screw 4 S2-51
13 1/4-20 hex flange nut 8 S281-4 39 Guide roller plate SW 1 270045
14 1” Inlet tube 1 S270054 40 SW support bracket 1 270043
15 Hose outlet support 1 270029 41 SW support bracket 1 270042
16 45° Elbow 1 None 42 Guide roller plate TW 1 270044
17 Bushing 1 300080 43 TW support bracket 1 270041
18 90° Ell 1 270028 44 TW support bracket 1 270040
19 Latch ratchet hub 1 S270001 45 Self tapping screw 4 S328-29
20 1/4-20 x 5/8” hex screw 4 S4-42 46 Coupling 1 None
21 Swivel assembly 1 S600888-2 47 #10 x 3/8” self tap screw 1 S32-136
22 Coupling reducer 1 S289-5 -- Hose ID and length -- None
23 1/2-20 hex flange nut 1 S280-8 -- Working pressure -- 500 PSI
24 10-32 x 3/8” nyloc nut 1 S82-15 -- Max. temperature -- 210° F
25 Latch pawl assembly 1 S600018
Description
#
FD9200 OLPBW
Req
Item
#
Description
#
FD9200 OLPBW
Req
Page 2
www.reelcraft.com
Loading...