ReelCraft E9450 OLP, E9305 OLP, E9340 OLP, E9275 OLP, E9399 OLP Operating Instructions Manual

Operating Instructions

Series E9000 Spring Driven Hose Reels

Low Pressure Model Numbers:

E9200 OLP E9330 OLP E9305 OLP E9450 OLP
E9275 OLP E9340 OLP E9399 OLP
E9299 OLP E9350 OLP E9400 OLP
E9300 OLP E9375 OLP E9430 OLP

Dimensions

A 26 1/4”

B 24 1/8”

C 4 3/4”

INSTALLATION:

LUBRICATION:

REPLACING HOSE:

D 12”

E 7 3/4”

F 22 1/4”

G 12 1/4”

The swivel union is packed separately in the reel carton, use teflon tape to assure a satisfactory seal. A flexible hose
connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and
binding. Non flexible connections will void the warranty, pressure rating of inlet hose must be equal to or more than
the pressure rating of the reel. Consult factory for proper spring when installing reels above 16 ft.

Hose reel spring and bearings are factory lubricated and require no further lubrication.

1. Wind spool flange clockwise-facing swivel-until spring is tight.

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to female outlet ell.

1. Models designed for fuel are coded with the prefix “F” i.e., “FE9400 OLP.”
Check name plate on the reel before installing.

2. Do not use reel at higher pressures or temperatures than listed on the back
of this bulletin.

3. Remove all spring tension before beginning dissassembly process.

4. Reel spring motor case is permanently sealed. Any attempt to remove the
spring motor may cause serious injury.

SAFETY

ADJUSTMENTS:

REPAIRS:

MODIFICATION:

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [e-mail] • www.reelcraft.com

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.

Hose latching mechanism can be removed for constant tension applications.

Form# 613-193 Rev: 6/2018

Series E9000 Spring Driven Hose Reels

11

10

9

8

7

6

5

4

3

3

2

1

12

13

37

14 15

36

6

1

38

16

17 9 1

3334

18 7 19

303132

20

4

21

22

23

2

24

25

26

27

28

29

6

39

40

41

3

42

43

6

3

44

Item

#

Part #

#

Req

Description

Item

#

Part #

#

Req

Description

1 S2-41 16 1/4-20 x 1/2” hex screw 24 S600454 1 Latch pawl assembly
2 270009 2 Side frame 25 S260067 1 Latch spring
3 S281-6 12 3/8-16 hex flange nut 27 S393-2 1 10-32 shoulder screw
4 S600416 2 Pillow block 30 S270016 2 Guide roller pin - long
5 270012 1 End frame support 31 S270015 2 Guide roller pin - short
6 S44-2 8 3/8-16 x 5/8” mach. screw 32 262436-5.468 2 Guide roller
7 S44-8 4 3/8-16 x 1 3/4” screw 33 262436-2.968 2 Guide roller
8 602377 1 Support shaft 34 S270014 4 Guide roller post

9 S140-34 6 Snap ring 36 270011 1 Hose guide roller plate
11 260888 1 Spring arbor 37 S2-51 4 5/16-18 x 1/2” hex screw
13 602364 1 Inlet tube 38 S281-4 8 1/4-20 hex nut
14 270029 1 Hose outlet support 39 270045 1 Guide roller plate SW
15 S32-136 1 #10 x 3/8” self tap screw 40 270043 1 SW support bracket
17 270028 1 90° female NPT ell 41 270042 1 SW support bracket
18 260889 1 Latch ratchet 42 270044 1 Guide roller plate TW
21 S280-8 1 1/2-20 hex flange nut 43 270041 1 TW support bracket
22 260934 1 Latch bracket 44 270040 1 TW support bracket
23 S82-15 1 10-32 x 3/8” nyloc nut

Page 2

www.reelcraft.com