ReelCraft E9000 Series, E9150 OHP, E9100 OHP, E9175 OHP Operating Instructions Manual
Operating Instructions
Series E9000 Spring Driven Hose Reels
High Pressure Model Numbers:
E9100 OHP E9150 OHP E9175 OHP
Dimensions
K
L
INSTALLATION:
B
A 26 1/4”
B 26 1/4”
C 13 3/4”
A
C
D 12 1/8”
E 24 1/4”
F 22 1/8”
D
E
F
G
G 7”
H 12”
J 7 3/4”
H
J
K 4”
L 7/16”
Four 7/16” diameter mounting holes
1. Do not use reel at higher pressures or temperatures than listed on the back
of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
3. Reel spring motor case is permanently sealed. Any attempt to remove the
spring motor may cause serious injury.
SAFETY
The swivel union is packed separately in the reel carton, use teflon tape to assure a satisfactory seal. A flexible hose
connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and
binding. Non flexible connections will void the warranty, pressure rating of inlet hose must be equal to or more than
the pressure rating of the reel. Consult factory for proper spring when installing reels above 16 ft.
LUBRICATION:
REPLACING HOSE:
Hose reel spring and bearings are factory lubricated and require no further lubrication.
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to female outlet ell.
ADJUSTMENTS:
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS:
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MODIFICATION:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
Hose latching mechanism can be removed for constant tension applications.
Form# 615-193 Rev: 6/2018
Series E9000 Spring Driven Hose Reels
7
6
3
3
2
1
10
9
8
5
4
14
1211
131
1615
1
9
1717
1918
4
20
41
42
6
21
3
22
43
2
23
41
24
42
6
26
3
27
43
37
36
35 6
33
32
31
29
30
28
Item
#
Part #
#
Req
Description
Item
#
Part #
#
Req
Description
Item
#
Part #
#
Req
Description
1 S2-41 16 1/4-20 x 1/2” hex screw 15 S32-136 1 #10 x 3/8” self tap screw 31 262436-5.468 2 Guide roller
2 270009 2 Side frame 16 S257-26 1 Swivel union 32 262436-2.968 2 Guide roller
3 S281-6 12 3/8-16 hex flange nut 17 260889 1 Latch ratchet 33 S270014 4 Guide roller post
4 S600416 2 Pillow block 18 S602033 1 Swivel assembly 35 270011 1 Hose guide roller plate
5 270012 1 End frame support 19 S168-3 1 Reducer 36 S2-51 4 5/16-18 x 1/2” hex screw
6 S44-2 8 3/8-16 x 5/8” machine screw 20 S280-8 1 1/2-20 hex flang nut 37 S281-4 8 1/4-20 hex nut
7 S44-8 4 3/8-16 x 1 3/4” screw 21 260934 1 Latch bracket 38 270045 1 Guide roller plate SW
8 270899 1 Support shaft 22 S82-15 1 10-32 x 3/8” nyloc nut 39 270043 1 SW support bracket
9 S140-34 6 Snap ring 23 S600454 1 Latch pawl assembly 40 270042 1 SW support bracket
10 600413-1 1 Spring & case assembly 24 S260067 1 Latch spring 41 270044 1 Guide roller plate TW
11 260888 1 Spring arbor 26 S393-2 1 10-32 shoulder screw 42 270041 1 TW support bracket
12 600415 1 Spool assembly 29 S270016 2 Guide roller pin - long 43 270040 1 TW support bracket
13 260894 8 Inlet tube assembly 30 S270015 2 Guide roller pin - short
14 270029 1 Hose outlet support
Item
#
Description
#
E9100 OHP E9150 OHP E9175 OHP
Req
27 Hose assembly 1 None S19-260044 S18-260044
28 Bumper stop assembly 1 None S602762 S602762
-- Hose ID and length -- None 3/8” x 50’ 3/8” x 75’
-- Working pressure -- 5000 PSI 4800 PSI 4800 PSI
-- Max. temperature -- 210 °F 210 °F 210 °F
Page 2
www.reelcraft.com
Loading...