Reelcraft E9000 User Manual

Operating Instructions

Series E9000 Spring Driven Hose Reels

Low Pressure Model Numbers:

E9200 OLP E9330 OLP E9400 OLP
E9275 OLP E9340 OLP E9430 OLP
E9299 OLP E9350 OLP E9450 OLP
E9300 OLP E9375 OLP

Dimensions

A 26 1/4”

B 24 1/8”

C 4 3/4”

D 12”

E 7 3/4”

F 22 1/4”

G 12 1/4”

SAFETY

1. Models designed for fuel are coded with the prefix “F” i.e., “FE9400 OLP.”
Check name plate on the reel before installing.

2. Do not use reel at higher pressures or temperatures than listed on the back
of this bulletin.

INSTALLATION:

LUBRICATION:

REPLACING HOSE:

ADJUSTMENTS:

REPAIRS:

H 13 7/8”

J 26 3/8”

The swivel union is packed separately in the reel carton, use teflon tape to assure a satisfactory seal. A flexible hose
connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and
binding. Non flexible connections will void the warranty, pressure rating of inlet hose must be equal to or more than
the pressure rating of the reel. Consult factory for proper spring when installing reels above 16 ft.

Hose reel spring and bearings are factory lubricated and require no further lubrication.

1. Wind spool flange clockwise-facing swivel-until spring is tight.

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to female outlet ell.

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.

3. Remove all spring tension before beginning dissassembly process.

4. Reel spring motor case is permanently sealed. Any attempt to remove the
spring motor may cause serious injury.

MODIFICATION:

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [e-mail] • www.reelcraft.com

Hose latching mechanism can be removed for constant tension applications.

Form# 613-193 Rev: 6/2013

Series E9000 Spring Driven Hose Reels

11

10

9

8

7

6

5

4

3

3

2

1

12

13

37

14 15

36

6

1

38

16

17 9 1

3334

18 7 19

303132

20

4

21

22

23

2

24

25

26

27

28

29

6

39

40

41

3

42

43

6

3

44

Item

#

Part #

#

Req

Description

Item

#

Part #

#

Req

Description

Item

#

Part #

#

Req

Description

1 S2-41 16 1/4-20 x 1/2” hex screw 15 S32-136 1 #10 x 3/8” self tap screw 32 262436-5.468 2 Guide roller
2 270009 2 Side frame 17 270028 1 90° female NPT ell 33 262436-2.968 2 Guide roller
3 S281-6 12 3/8-16 hex flange nut 18 260889 1 Latch ratchet 34 S270014 4 Guide roller post
4 S600416 2 Pillow block 21 S280-8 1 1/2-20 hex flange nut 36 270011 1 Hose guide roller plate
5 270012 1 End frame support 22 260934 1 Latch bracket 37 S2-51 4 5/16-18 x 1/2” hex screw
6 S44-2 8 3/8-16 x 5/8” mach. screw 23 S82-15 1 10-32 x 3/8” nyloc nut 38 S281-4 8 1/4-20 hex nut
7 S44-8 4 3/8-16 x 1 3/4” screw 24 S600454 1 Latch pawl assembly 39 270045 1 Guide roller plate SW
8 602377 1 Support shaft 25 S260067 1 Latch spring 40 270043 1 SW support bracket

9 S140-34 6 Snap ring 27 S393-2 1 10-32 shoulder screw 41 270042 1 SW support bracket
11 260888 1 Spring arbor 30 S270016 2 Guide roller pin - long 42 270044 1 Guide roller plate TW
13 602364 1 Inlet tube 31 S270015 2 Guide roller pin - short 43 270041 1 TW support bracket
14 270029 1 Hose outlet support 44 270040 1 TW support bracket

Item

#

10 Spring case assembly 1 600413-1 600413-1 600413-1 S600413-2 600413-2 600413-2 600413-2 600413-2 600413-2 600413-2 600413-2

12 Sheave assembly 1 600415 600415 600415 600415 600415 600415 600415 600415 600414 600414 600414

16 Reducing bushing 1 300080 300080 300080 270025 270025 270025 270025 270025 None None None

19 Swivel assembly 1 600888 600888 600888 S602026 S602026 S602026 S602026 S602026 S600682-1S600682-1 S600682-1

20 Reducing coupling 1 S289-5 S289-5 S289-5 S289-6 S289-6 S289-6 S289-6 S289-6 None None None

28 Hose assembly 1 None 601020-75 601020-100 None 601026-30 601026-40 S601026-50 601026-75 None 601027-30 601027-50

29 Hose bumper assembly 1 None 2-HR1005 2-HR1005 None 3-HR1005 3-HR1005 3-HR1005 3-HR1005 None 4-HR1005 4-HR1005

-- Hose ID and length -- None 1/2” x 75’ 1/2” x 100’ None 3/4” x 30’ 3/4” x 40’ 3/4” x 50’ 3/4” x 75’ None 1” x 30’ 1” x 50’

-- Working pressure -- 500 PSI 300 PSI 300 PSI 500 PSI 300 PSI 300 PSI 300 PSI 300 PSI 500 PSI 300 PSI 300 PSI

-- Max. temperature -- 210° F 150° F 150° F 210° F 150° F 150° F 150° F 150° F 210° F 150° F 150° F

Description

#

Req

E9200

OLP

E9275

OLP

E9299

OLP

E9300

OLP

E9330

OLP

E9340

OLP

E9350 OLP

E9375

OLP

E9400

OLP

E9430

OLP

E9450

OLP

Page 2

www.reelcraft.com