Reelcraft E8000 User Manual

Operating Instructions

Series E8000 Spring Driven Hose Reels

Low, Medium and High Pressure Model Numbers:

E8800 OLP E8650 OMP E8450 OHP
E8850 OLP E8800 OMP E8600 OHP
E8600 OMP E8850 OMP E8650 OHP

Dimensions

A 21 1/8”

B 19”

C 7 7/8”

D 3 7/8”

E 9 1/4”

Caution: When changing guide arm positions, the U-bolt must
be placed in the proper location as instructed below. The reel
can “latch out” during use if this instruction is not adhered to.

SAFETY

1. Do not use reel at higher pressures or temperatures
than listed on the back of this bulletin.

2. Remove all spring tension before beginning
dissassembly process.

INSTALLATION:

MOUNTING:

LUBRICATION:

REPLACING HOSE:

ADJUSTMENTS:

A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.

The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.

Hose reel spring and bearings are factory lubricated and require no further lubrication.

1. Wind spool flange clockwise-facing swivel-until spring is tight.

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to swivel joint and secure hose with clamps.

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.

REPAIRS:

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [e-mail] • www.reelcraft.com

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.

Form# 616-193 Rev: 4/2013

Series E8000 Spring Driven Hose Reels

4

3

2

11

10

9

8

7

6

5

13

1

14

15

16

17

18

19

20

21

22

23

28

24

25

26

Item

#

1 Hose Assembly 1 None 601021-50 None 5-260043 None 8-260043 9-260044 None 5-260044
2 Swivel Assembly 1 S600923 S600923 S600300 S600300 S600300 S600300 S602033 S602033 S602033
3 Sheave Assembly 1 S600427 S600427 S600427 S600427 S600427 S600427 S600427 S600427 S600427
4 Drive Spring Assembly 1 S260037 S260037 S260053 S260053 S260053 S260053 S260053 S260053 S260053
5 Spring Arbor Assembly 1 S600621 S600621 S600621 S600621 S600621 S600621 S600621 S600621 S600621
6 Gasket 1 260901 260901 260901 260901 260901 260901 260901 260901 260901
7 Spring Case Assembly 1 S600424 S600424 S600424 S600424 S600424 S600424 S600424 S600424 S600424
8 10-32 Hex Lock Nut 6 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15

9 Main Shaft 1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1
10 Snap Ring 3 300007 300007 300007 300007 300007 300007 300007 300007 300007
11 Hose Bumper Assembly 1 None
13 Guide Arm Assembly 1 260007 260007 260007 260007 260007 260007 260007 260007 260007
14 5/16-18 x 1-1/4” Screw 3 507286 507286 507286 507286 507286 507286 507286 507286 507286
15 1/2-13 Set Screw 1 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86
16 1/2-20 Hex Flange Nut 1 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8
17 Base 1 260073 260073 260073 260073 260073 260073 260073 260073 260073
18 Latch Spring 1 S260067 S260067 S260067 S260067 S260067 S260067 S260067 S260067 S260067
19 Latch Bushing 1 S400012 S400012 S400012 S400012 S400012 S400012 S400012 S400012 S400012
20 10/24 x 1” Screw 1 300042 300042 300042 300042 300042 300042 300042 300042 300042
21 Latch Pawl Assembly 1 S600083 S600083 S600083 S600083 S600083 S600083 S600083 S600083 S600083
22 3/8-24 Hex Jam Nut 1 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106
23 Spring Case Stud 1 S260031 S260031 S260031 S260031 S260031 S260031 S260031 S260031 S260031
24 O-ring 2 904217 904217 904217 904217 904217 904217 904217 904217 904217
25 U-bolt 1 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440
26 1/4-20 Nyloc Nut 2 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1
28 Swivel Union 1 S257-26 S257-26 S257-26 S257-26 S257-26 S257-26 S257-72 S257-72 S257-72

Hose I.D. and Length None 1/2” x 50’ None 3/8” x 50’ None 1/2” x 50’ 1/4” x 50’ None 3/8” x 50’
Reel Inlet Connection 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT
Max. Operating Pressure 500 PSI 300 PSI 3000 PSI 2600 PSI 3250 PSI 3250 PSI 5000 PSI 5000 PSI 4800 PSI
Max. Operating Temperature 210° F 150° F 210° F 210° F 210° F 210° F 210° F 210° F 210° F

Description

#

Req.

E8800

OLP

E8850

OLP

A2-HR1004-3

E8600

OMP

None

E8650

OMP

A1-HR1004-3

E8800

OMP

None

E8850

OMP

A2-HR1004-3 A1-HR1004-3

E8450

OHP

E8600

OHP

None

E8650

OHP

A1-HR1004-3

Page 2

www.reelcraft.com