Reelcraft D9000 User Manual
Operating Instructions
Series D9000 Spring Driven Hose Reels
For Diesel Exhaust Fluid (DEF)
URD9200 OLBBW70 URD9300 OLBBW70
URD9275 OLBBW70 URD9350 OLBBW70
Dimensions
A 26 1/4”
B 24 1/8”
C 4 3/4”
D 12”
E 7 3/4”
Four 7/16” diameter mounting holes
INSTALLATION:
LUBRICATION:
REPLACING HOSE:
ADJUSTMENTS:
F 22 1/4”
1. Do not use reel at higher pressures or temperatures than listed on the back
G 12 1/4”
H 13 7/8”
J 26 3/8”
The swivel union is packed separately in the reel carton, use teflon tape to assure a satisfactory seal. A flexible hose
connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and
binding. Non flexible connections will void the warranty, pressure rating of inlet hose must be equal to or more than
the pressure rating of the reel. Consult factory for proper spring when installing reels above 16 ft.
Hose reel spring and bearings are factory lubricated and require no further lubrication.
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to female outlet ell.
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
3. Reel spring motor case is permanently sealed. Any attempt to remove the
spring motor may cause serious injury.
SAFETY
REPAIRS:
MODIFICATION:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Hose latching mechanism can be removed for constant tension applications.
Form# 1234-1011 Rev: 7/2012
Series D9000 Spring Driven Hose Reels
Item
Part #
#
1 S2-41 4 1/4-20 x 1/2” Hex Screw 19 S2-42 4 1/4-20 x 5/8” Hex Screw
2 270009 2 Side Frame 21 S280-8 1 1/2-20 x 5/8” Hex Screw
3 S281-6 12 3/8-16 Hex Flange Nut 22 S82-16 1 Nut, Nyloc
4 S270058 2 Pillow Block 23 S600018 1 Latch Pawl Assembly
5 270012 1 End Frame Support 24 S260067 1 Latch Spring
6 S44-2 8 3/8-16 x 5/8” Screw 26 S393-2 1 10-32 Shoulder Screw
7 S44-8 4 3/8-16 x 1-3/4” Screw 28 A3-HR1005 1 Hose Bumper
8 602314 1 Support Shaft 29 S270016 2 Guide Roller Pin - Long
9 S140-31 5 Snap Ring 30 S270015 2 Guide Roller Pin - Short
10 S270105 1 Spring & Case Assembly 31 262436-5.468 2 Guide Roller
11 S270002 1 Spring Arbor 32 262436-2.968 2 Guide Roller
12 270107 1 Sheave Assembly 33 S270014 4 Guide Roller Post
13 S281-4 8 1/4-20 Hex Flange Nut 34 270011 1 Hose Guide Roller Plate
14 261047 1 Inlet Tube 35 S2-51 4 5/16”-18x1/2” Hex Screw
15 270029 1 Hose Outlet Support 36 S32-136 1 #10 x 3/8” Self Tap Screw
17 S160-16 1 90° Elbow
18 S270001 1 Latch Ratchet Hub
Item
Description
#
16 Reducer Bushing 1 S380-112 S380-112 S380-113 S380-113
20 Swivel Assembly 1 602471-2 602471-2 602472-2 602472-2
27 Hose Assembly 1 None 601101-75 None 601105-50
#
Req
#
Req
Description
URD9200
OLBBW70
Item
#
URD9275
OLBBW70
Part #
#
Req
URD9300
OLBBW70
Description
URD9350
OLBBW70
Page 2
www.reelcraft.com
Loading...