ReelCraft L CA37122 L, CA37128 L, CA37118, EA37128 L12D, EA37118 L12D Operating Instructions Manual

Operating Instructions

Series 37000 Hose Reels

CA37118 L CA37122 L CA37128 L
EA37118 L12D EA37122 L12D EA37128 L12D

Dimensional Data

A
B

D

C

Safety Precautions

Personal injury and/or equipment
damage may result if proper safety
precautions are not observed.

• Ensure that the reel has been properly
installed before connecting supply line
(see installation instructions).

Part # A B C D

CA37118 L

EA37118 L12D

CA37122 L

EA37122 L12D

CA37128 L

EA37128 L12D

• Do not play pranks on other personnel.
Even low pressure is very dangerous
and can cause irrepairable damage or
death.

• Do not wear loose fitting clothing while
operating reel.

31 3/4” 18” ----- 21 3/4”

----- 18” 31 1/4” 21 3/4”

35” 22” ----- 25 3/4”

----- 22” 35 1/4” 25 3/4”

40” 27” ----- 30 3/4”

----- 27” 40 1/4” 30 3/4”

• If a leak occurs in the hose or reel,
remove supply line pressure
immediately.

• If the reel is power driven check for
loose, frayed, and/or broken wires before
operating.

• Bleed fluid/gas pressure from system
before servicing reel.

• Before connecting reel to supply line
ensure that supply line pressure does
not exceed maximum rated working
pressure of reel.

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [e-mail] • www.reelcraft.com

• Be aware of other personnel in work
area.

• Be aware of other machinery in work
area.

• Treat and respect a hose reel as any
other piece of machinery, observing all
common safety practices.

Form# 1109-1101 Rev: 10/2016

Series 37000 Hose Reels

INSTALLATION INSTRUCTIONS

Inspection

Unpack and inspect the reel for damage.
Turn the reel by hand to check for smooth
operation. Check for completeness.

Mounting of all hose reels
NOTE: Ensure that mounting surface is

flat to prevent binding on reel after it is
mounted.

1. Two 1/2” diameter mounting holes are
located at the base of each side
support panel (2 each). Mount reel
using four (customer supplied) bolts;
tightening them securely to ensure a
solid, rigid attachment.

2. Perform the following steps only after
all other installation steps, pertaining
to your particular reel, are
accomplished. Refer to page 4 for
special instructions.
NOTE: A flexible hose connection must be
used to compensate for any offset between
the supply line and the reel swivel.

3. Apply thread compound to all threads.

4. Thread male connector of supply line
into swivel. Tighten securely.

Manual Driven Reels

Additional mounting instructions are not
required.

Power Drive Reels
CAUTION: Remove all electrical power

when wiring. Do not “hot-wire”. Observe
all applicable NEC/OSHA requirements.

1. Ensure that supply and motor voltage
ratings are compatible.

2. Consult wiring diagrams and determine
which one is applicable to your reel.

3. Perform electrical wiring following
applicable diagram.

DOUBLE POLE SINGLE-THROW SWITCH

110 Volt A.C.

Hot

Neutral

SINGLE POLE SINGLE-THROW

Connection shown
gives counter­clockwise rotation
looking at end of
motor shaft. To
reverse rotation
interchange Leads
5, 6.

12/24 VOLT D.C.

Connecting the hose
CAUTION: Do not connect the hose to the

connecting tube assembly until after hose
reel has been installed. Fully extend and
charge hose before winding on to reel.
Momentarily open control valve, when
initially charging, to purge hose of gases.
When fluid appears at control valve, close
valve. This prevents flattening of the hose
and excessive pressure on the drum when
fluid supply is reinitialized at a later time.

3. Using a wrench, firmly hold onto
connecting tube assembly while
tightening hose connector.

OPERATING INSTRUCTIONS

WARNING-PREVENT STATIC
SPARKING: When working around flam-

mable liquids such as solvents, paints,
chemicals or petroleum products, ensure
that the hose reel, hose and the equipment
being serviced are properly grounded.
Use grounded hose(s) (static wire). Use
an ohmmeter to check continuity of the
ground circuit. Fire and/or explosion can
result if proper grounding is not achieved.
If reel is power or air driven, be careful of
chain/sprocket drive system. Keep hands
clear. Do not wear loose fitting cloth­ing. Pull hose from the reel by grasping
the hose itself, not the control handle or
swivel.

SERVICE INSTRUCTIONS

Replacing the hose

1. Using a wrench, firmly hold onto the
connecting tube assembly while
removing hose connector.

2. Follow procedures for “Connecting the
hose” (refer to installation
instructions).

Page 2

1. Apply thread compound to all threads.

2. Hand thread male hose connector into
connecting tube assembly.

www.reelcraft.com