ReelCraft A5800 OMP, A5825 OMP, 5000 Series, A5800 OLP, A5825 OLP Operating Instructions Manual

Operating Instructions

Series 5000 Spring Driven Hose Reels

Low and Medium Pressure Model Numbers:

A5800 OLP A5800 OMP
A5825 OLP A5825 OMP

Dimensions

A 14 3/8”

B 14”

C 9 3/4”

SAFETY

INSTALLATION:

MOUNTING:

LUBRICATION:

REPLACING HOSE:

D 2 1/2”

E 6 1/8”

A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.

The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.

Hose reel spring and bearings are factory lubricated and require no further lubrication.

1. Wind spool flange clockwise-facing swivel-until spring is tight.

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to swivel joint and secure hose with clamps.

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.

2. Remove all spring tension before beginning dissassembly process.

ADJUSTMENTS:

REPAIRS:

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [e-mail] • www.reelcraft.com

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.

Form# 1170-505 Rev: 4/2013

Series 5000 Spring Driven Hose Reels

Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description

1 300031 2 1” Snap Ring 13 S300011 7 Hex Lock Nut 23 300001 5 10-32 x 3/8” Screw
2 300034 2 Spacing Washer 14 S505740 1 Drive Spring Assembly 24 400020 1 O-ring
3 S295-102 3 1/4-10 Hex Head Screw 15 S261360 1 Spring Case Stud 25 S400109 1 Latch Plate Assembly
4 260022 1 Flange Sheave 16 300006 1 3/8-16 x 1/2” Set Screw 26 300035 1 10-32 x 1” Mach. Screw
5 500006 1 Sheave Disk 17 S500103 1 Spring Case & Hub Assembly 27 3-117440 1 U-bolt Hose Clamp
6 S500019 1 Latch Cam 18 S82-15 1 10-32 x 3/8” Nyloc Nut 28 261650-1 2 1/4-20 Zinc Nyloc Nut
7 S260648 1 Spring Arbor 19 S400021 1 Latch Bumper

8 300002 2 10-32 x 1/2” Mach. Screw 20 S32-136 1 10-24 x 3/8” Self Tap Screw
11 S500107 1 Guide Arm & Roller Assembly 21 S400012 1 Latch Bushing
12 500101 1 Base Assembly 22 S400018 1 Latch Spring

Item # Description # Req.

9 Hose Bumper Assembly 1 None 2-HR1004-3 None 2-HR1004-3
10 Hose Assembly 1 None 601020-25 None 21-260043
31 Swivel Union 1 300010 300010 260749 260749
32 Swivel Union 1 300010 300010 S257-26 S257-26
33 Swivel Assembly 1 S600887-1 S600887-1 S600595-1 S600595-1

Hose I.D. and Length None 1/4” x 20’ 1/4” x 25’ 1/4” x 30’
Reel Inlet Connection 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T.
Max. Operating Pressure 500 P.S.I. 300 P.S.I. 3250 P.S.I. 3250 P.S.I.
Max. Operating Temperature 210° F 150° F 210° F 210° F

Model

A5800 OLP

Model

A5825 OLP

A5800 OMP

30 602305 1

Model

Model

A5825 OMP

Main Shaft & Snap Ring
Assembly

Page 2

www.reelcraft.com