Page 1
Operating Instructions
Series 5000 Spring Driven Hose Reels
Enclosed Pre-Rinse Model Numbers:
5635 ELPSW5
Dimensions
A 15”
B 16 1/4”
C 9 3/4”
SAFETY
INSTALLATION:
MOUNTING:
LUBRICATION:
REPLACING HOSE:
D 2 1/2”
E 7”
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the 1/4-20 hex nuts (4) fastening the hose guide enclosure to the reel back cover. Shift the hose guide
enclosure to the desired position and replace the 1/4-20 hex nuts. NOTE: For proper installation in wall mount
applications, ensure reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause
latching issues.
Hose reel spring and bearings are factory lubricated and require no further lubrication.
1. Remove 1/4-20 hex nuts (4) which fasten the hose guide enclosure to the reel back cover and pull off the
enclosure.
2. Wind spool flange clockwise-facing swivel-until spring is tight.
3. Back off three turns and latch.
4. Insert hose through roller guide.
5. Connect hose fitting to swivel joint and secure hose with clamps.
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
ADJUSTMENTS:
REPAIRS:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Form# 1261-314 Rev: 5/2018
Page 2
Series 5000 Spring Driven Hose Reels
Hose I.D. and Length 3/8” x 35’
Reel Inlet Connection 3/8” NPT(F)
Max. Operating Pressure 250 PSI
Max. Operating Temperature 210 °F
6
5
4
3
2
1
16
17
15
14
18
13
12
11
10
9
8
7
19
20
21
22
23
24
25
26
27
28
31
35
30
32
33
34
Item # Part # # Req. Description Item # Part # # Req. Description
1 500102 1 Case and Cover Assembly 19 S82-15 1 10-32 x 3/8” Nyloc Nut
2 300001 4 10-32 x 3/8” Screw 20 S400021 1 Latch Bumper
3 S600886 1 Swivel Assembly 21 S32-136 1 10-24 x 3/8” Screw
4 300031 1 1” Snap Ring 22 S400018 1 Latch Spring
5 300034 4 Spacing Washer 23 300002 7 10-32 x 1/2” Screw
6 S295-102 3 1/4-10 x 5/8” Hex Screw 24 S400012 1 Latch Bushing
7 260022 1 Sheave Flange 25 400020 7 O-ring
8 500006 1 Sheave Disk 26 S400109 1 Latch Plate Assembly
9 S500019 1 Latch Cam 27 300035 1 10-32 x 1” Mach. Screw
10 S260648 1 Spring Arbor 28 3-117440 1 Hose Clamp
11 500004 1 Reel Cover 30 S400015 1 Main Shaft
12 300070 4 1/4-20 Nyloc Nut 31 601052-35 1 Hose Assembly
13 500101 1 Base Assembly 32 1-HR1004 1 Bumper Stop
14 504240 1 Drive Spring Assembly 33 S260019 1 Guide Roller Pin Kit
15 S261360 1 Spring Case Stud 34 HR2012 1 Hose Guide Assembly
16 S500103 1 Spring Case Assembly 35 261650-1 2 1/4-20 Nyloc Nut
17 300006 1 3/8-16 x 1/2” Set Screw 36 S600080 1 Spray Valve
18 S300011 7 10-32 Hex Lock Nut 37 600248 * 360° Swivel (Optional)
37
36
Page 2
www.reelcraft.com
Loading...