Page 1
Operating Instructions
Series 5000 Spring Driven Hose Reels
Low Pressure Model Numbers:
5600 OLB
Dimensions
A 14 3/8”
B 14”
C 9 3/4”
SAFETY
INSTALLATION:
MOUNTING:
LUBRICATION:
REPLACING HOSE:
D 2 1/2”
E 6 1/8”
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.
Hose reel spring and bearings are factory lubricated and require no further lubrication.
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
ADJUSTMENTS:
REPAIRS:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Form# 581-1091 Rev: 4/2018
Page 2
Series 5000 Spring Driven Hose Reels
Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description
1 300031 2 1” Snap Ring 11 500101 1 Base Assembly 23 400020 5 O-ring
2 300034 2 Spacing Washer 13 S504240 1 Drive Spring Assembly 24 S400109 1 Latch Plate Assembly
3 S295-102 3 1/4” Plastite Hex Screw 14 S261360 1 Spring Case Stud 25 300035 1 10-32 x 1” Mach. Screw
4 260022 1 Sheave Flange 15 300006 1 3/8-16 x 1/2” Set Screw 26 3-117440 1 U-bolt
5 500006 1 Sheave Disk 16 S500103 1 Spring Case Assembly 27 261650-1 2 1/4-20 Zinc Nyloc Nut
6 S50019 1 Latch Cam 17 S82-15 8 10-32 x 3/8” Nyloc Nut 28 260227-B 1 Main Shaft**
7 S260648 1 Spring Arbor 18 S400021 1 Latch Bumper 28 S262922-B 1 Main Shaft
8 300002 7 10-32 x 1/2” Screw 19 S32-136 1 10-24 x 3/8” Mach. Screw 29 600374-1B 1 Swivel Assembly**
9 1-HR1004A 1 Bumper Stop Assembly 20 S400012 1 Latch Bushing 29 602689-1B 1 Swivel Assembly
10 S500107 1 Guide Arm & Roller Assembly 21 S400018 1 Latch Spring 30 S160-3 1 Street Ell
Specifications
Hose I.D. and Length None
Reel Inlet Connection 3/8” FPT
Max. Operating Pressure 300 psi
Max. Operating Temperature 210 °F
**Prior to August 2016
See online tech bulletin for more information
Page 2
www.reelcraft.com
Loading...