ReelCraft 4000 Series, 4615 OLP, 4430 OLP, 4400 OLP, 4620 OLP Operating Instructions Manual

Operating Instructions

Series 4000 Spring Driven Hose Reels

Low Pressure Model Numbers:

4400 OLP 4430 OLP 4615 OLP 4620 OLP
4420 OLP 4435 OLP 4617 OLP 4625 OLP
4425 OLP 4600 OLP

Dimensions

A 12 7/8”

A

D

Four 5/16” diameter mounting holes

INSTALLATION:

MOUNTING:

LUBRICATION:

B 12 5/8”

B

C

E

A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.

The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.

Hose reel spring and bearings are factory lubricated and require no further lubrication.

C 8”

D 2 1/2”

E 5 3/8”

SAFETY

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.

2. Remove all spring tension before beginning dissassembly process.

REPLACING HOSE:

ADJUSTMENTS:

REPAIRS:

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
[e-mail] • www.reelcraft.com

1. Wind spool flange clockwise-facing swivel-until spring is tight.

2. Back off three turns and latch.

3. Insert hose through roller guide.

4. Connect hose fitting to swivel joint and secure hose with clamps.

To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.

Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.

Form# 491-884 Rev: 8/2011

Series 4000 Spring Driven Hose Reels

1

2

3

4

5

6

7

8

10

9

11

12

13

14

23

15

16

17

18

19

20

21

22

24

25

30

Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description

1 600886 1 Swivel Assembly 12 400107 1 Guide Arm Assembly 22 400012 1 Latch Bushing
2 300031 2 1” Snap Ring 13 400101 1 Base Assembly 23 400018 1 Latch Spring
3 300034 2 Spacing Washer 15 261360 1 Spring Case Stud 24 300001 5 10-32 x 3/8” Screw
4 S295-102 3 1/4” Plastite Hex Screw 16 300011 7 10-32 Hex Lock Nut 25 400020 1 O-ring
5 400005 1 Flange Assembly 17 300006 1 3/8-16 x 1/2” Set Screw 26 400109 1 Latch Plate Assembly
6 400006 1 Sheave Disk 18 400103 1 Spring Case Assembly 27 300035 1 10-32 x 1” Mach. Screw
7 400019 1 Latch Cam 19 S82-15 1 10-32 x 3/8” Nyloc Nut 28 3-117440 1 U-bolt
8 260648 1 Spring Arbor 20 400021 1 Latch Bumper 29 261650-1 2 1/4-20 Zinc Nyloc Nut
9 300002 2 10-32 x 1/2” Screw 21 S32-136 1 10-24 x 3/8” Mach. Screw 30 400015 1 Main Shaft

Item # Description # Req. 4400 OLP 4420 OLP 4425 OLP 4430 OLP 4435 OLP 4600 OLP 4615 OLP 4617 OLP 4620 OLP 4625 OLP

10 Hose Bumper Assembly 1 None A1-HR1004A A1-HR1004A A1-HR1004A A1-HR1004A None A1-HR1004 A1-HR1004 A1-HR1004 A1-HR1004
11 Hose Assembly 1 None 601001-20 601001-25 601000-30 601001-35 None 601011-15 601011-17 601011-20 601013-25

14 Drive Spring Assembly 1 400030 400030 400030 400030 400030 404230 404230 404230 404230 404230
Hose I.D. and Length None 1/4” x 20’ 1/4” x 25’ 1/4” x 30’ 1/4” x 35’ None 3/8” x 15’ 3/8” x 17’ 3/8” x 20’ 3/8” x 25’
Reel Inlet Connection 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T.
Max. Operating Pressure 500 P.S.I. 300 P.S.I. 300 P.S.I. 300 P.S.I. 300 P.S.I. 500 P.S.I. 300 P.S.I. 300 P.S.I. 300 P.S.I. 300 P.S.I.
Max. Operating Temperature 210° F 150° F 150° F 150° F 150° F 210° F 150° F 150° F 150° F 150° F

29

28

27

26

Page 2

www.reelcraft.com