Page 1
R450+
Chain Vise Tripod (R450+, R45OC, R45OP, R470+)
Replacement Parts
19
20
23
18
21
24
17
22
25
26
28
30C
16
16C or 16P
27
1C
8
5
6
1
7
9
14
A
R470+
12
29
Capacity: 1/8" Through 6"
Patented
Ref. Description REED (pack) REED
1A R450+ Base with Wear Plate and Screws 99050 41170 / 72097* —
1B R470+ Base with Wear Plate and Screws 99403 — —
2 X-7002-B5190425099ylbmessA yarT & geL
3 T 844-C0421440099yarT loo
4 Tray Support Clamp w/screw & nut 99054 41235 D-488-X
5 W 9331-E5590422099etalP rae
6 Screw for wear plate (2) 5 Pk=99069 39002 40960 E-75-X
7 868-E076647810308099=kP 5)3( tloB geL
8 4901-E522442300317099=kP 5)3( tuN
9 Lock Washer (5) 5 Pk=99072 30033 40930 E-1095
11 "X" Washers (6) 5 Pk=99073 99010 41270 E-1377
Replaces Ridgid®
Parts List
N/P dlO.oN taCedoC metIedoC metI.oN
——15099esaB mooR naelC C054RC1
X-5731-E5621435099)6( srehsaW "X"/w )3( sniP yarT01
X-5831-E5521475099)2( ylbmessA geL tnorF21
X-9831-E0521485099ylbmessA geL raeR31
——38104pirG eldnaH41
X-4441-E5490455099ylbmessA niahC geL51
——5209957099=riaP)2( swaJ61
Ref. Description REED (pack) REED
17 Jaw Screws & Nuts (2) 5 Pk=99059 99084 NI NI
29 Grommet (3) 40171 40940 F-532
30C R450C Chain Cover for clean rooms 99030 — —
NI - Not Interchangable with Ridge Tool Co. parts. ® Ridgid is a registered trademark of Ridge Tool Co.
*First number is for Ridgid 450, second number for Ridgid 460.
4
15
11
3
A
10
29
13
2
Replaces Ridgid®
N/P dlO.oN taCedoC metIedoC metI.oN
ININ8209967099=riaP)2( C054RC61
3209977099=Pair)2( P054RP61
ININ70029eldnaH81
X-1713-E0501406099ylbmessA wercS & eldnaH91
ININ16099rehsaW & tuN htiw eldnaH02
ININ42099rehsaW tsurhT12
ININ02099wercS niahC22
ININ65029niP relloR32
8842-E0990401029relloR42
—*29027 / 5701431099ylbmessA niahC52
1872-E0401422129niP wercS niahC62
—*20127 / 0321446099ylbmessA wercS kcaJ72
3874-E0561363439niP gnikcoL tuN82
Page 2
R450+ & R40+ Series Tripods
Operation & Instructions For Assembling Legs & Tray
R450+ Chain Vise Tripod
RUBBER OPTIONALROTATE TO RENEW TEETH
R450P Plastic Pipe Tripod
R450C Clean Room Tripod
R40+ Yoke Vise Tripod
R470+ Chain Vise Tripod
Patented
VISE SCREW
BENDING
GROOVES
CHAIN
TRAY
SUPPORT CLAMP
CLAMP SCREW
JACK SCREW
BASE
6" PIPE REST
BOLT, NUT &
WASHER
HANDLE GRIP
REAR LEG
ADJUST CLAMP
A
CHAIN
FOOT
A
Replacement Parts Assembly
TRAY PIN
1) For easier assembly, place the base upside down on a flat surface.
2) Insert rear leg in base with foot pointing outward as shown. Secure to base with bolt, nut, and washer. Tray support is preset with a clamp collar for approximate position and is adjustable. (see "Tray Adjustment" note below).
3) Insert front legs so feet are pointing outward and secure to base with bolts, washers, and nuts.
4) To assemble tray, open tray so that side of flanges are facing bottom of base. Attach the rear leg first with tray pin
then proceed to front legs.
5) Push "X" washers in pin grooves and pinch long ends together with pliers.
6) Stand tristand on legs. If you have a yoke vise tripod, assemble yoke to base. The hook on the yoke can either be
on the right or left side depending on operator.
"X" WASHER
Operation and Maintenance
JAWS — To renew teeth—remove jaw screws and nuts, rotate jaws in either direction, replace jaw screws and nuts and tighten.
TRAY ADJUSTMENT— If folding tray does not snap into position and hold legs rigid when tripod is set up, loosen
clamp screw in rear leg tray support and slide support clamp upward — tighten clamp screw securely.
JACK SCREW — Used with a length of 1" pipe as an adjustable ceiling brace to anchor tripod, but for large heavy
pipe, fasten feet of tripod to floor securely.
BENDERS — Place pipe, conduit, or tubing into holes provided on base and pull down into grooves.
HANDLE GRIP — To install new handle grip over top of rear leg, insert compressed air hose nozzle under bottom edge
and pull down while expanding with air flow.
LUBRICATION — Perodically lubricate the tray hinge, vise screw, jack screw, and chain with oil or spray silicone.
Loading...