OPERATION MANUAL
3 IN ONE DATALOGGER PRINTER
MODEL: 9801 9802
Thank you for p urchasing t his 3 in one Hand H eld
Datalogge r Printer. This port able device i s the
first 3 in one da talogger pr inter on the ma rket.
FEATUREFEATURE
Datalogge r programme r and printer
Print in grap hic (2 modes) o r text mode
USB port to PC li nk
Saving max. 4 l ogger memor ies
Powered by 4p cs AAA batteries
Optional 9V DC adaptor fo r long time use
Low battery w arning
Datalogge r printer
4pcs AAA batteries
One thermo pa per roll
Instructi on manual
Logger link c able
Software +U SB cable
Optional:
-9VDC adapt or
-Datalogg er
MATERIAL SUPPLYMATERIAL SUPPLY
PAPER FEEDINGPAPER FEEDING
Ope n the pri nter co ver Ins ert the s harp- cut to
the p rinte r Pre ss if you c an’t
eas ily pul l out the s harp- cut Don e!
car tridg e
POWER SUPPLY & PORT ILLUS TRATIONPOWER SUPPLY & PORT ILLUS TRATION
The m eter is p owere d by 4pcs AA A bat terie s
or on e 9VDC (> 0.5A) a dapto r.
Whe n "Low Ba ttery " appea rs on LCD : Tur n off
the p rinte r Repla ce the ba ttery w ith cor rect
pol arity a nd make g ood con tact Do ne!
USB port
Connect to PC to download
the printer memories.
(Disabled in
9801/02)
9VDC
USB
Cont act Poi nts
Contact Points
For loggers with two metal contacts to connect
with printer. Including: 88128/8828/8829/8813/
8814/8815/8833/8834/8835/88335/88345/88355.
KEYPADKEYPAD
Men u
Up
Dow n
Ent er
Fee d
LCD
dis play
Normal: Select the pervious/next option.
Modified Mode: increase/decrease the the value.
You may press and hold for quick jump.
Power On: Press to turn on the printer.
Normal : To turn to the next page.
Escape : Escape without saving.
Printing : Press the button to stop printing.
Power Off: Press for 3 seconds to turn off.
Normal : To enter modification mode or run a
command.
Modification Mode: Press to enter next digit or
end modification with saving.
Feed the paper when it's inactive except printing.
PRINT PAGE (PRN)
To custom made the
printing content you
need, press /
to highlight the
field which need to be
configured and then
press to enter the modification.
NOTE: If you want to print the data of logger
which is plugged in, the Download command
must run first.
CONTRAST
Valid values for Contrast
: 1 to 9 (light to heavy).
During printing, you can
press / to
change the contrast
any time.
To set the contrast, highlight the contrast field and
press to enter.
Press / to increase/decrease the value
of contrast.
Press to end the modification with saving
the value, or press to end without saving.
ALARM
This field allows you to set the alarm critical value
for printing. To set the alarm, highlight the Alarm
field and press to enter.
Press / to enable/disable the alarm.
Press to save the modification or press
to escape without saving.
If you select enable mode, alarm setting must be
edited.
Press / to
increase/decrease the
highlighted value, press
to highlight the
next. The alarm setting
will exit and save when
you press in the
last value.
Valid values for Air temp.
/external temp./RH%:
Air Hi:-40.0 to185
Air Lo: -40.0 to 185
Ext. Hi: -40.0 to 212
Ext. Lo: -40.0 to 212
%RH Hi: 0.0 to 100
%RH Lo: 0.0 to 100
MODE
This field allows you to set the printing mode. To
set the printing mode, highlight the Mode field and
press to enter modification.
Press / to select the printing mode.
Press to save or press to escape
the modification without saving. You can choose
Graph or Report (Summary) or Text mode.
Report Mode: Print logger summary information
and compact chart of all data.
Graph Mode: Print logger detailed chart page by
page. Data range is selected in
"Content" option before printing.
Text Mode: Print logger detailed data one by
one. Data range is selected in
"Content" option before printing.
If text is printed with underline
means the value is over the printing
alarm (see page 7)
1
2
4
6
7
8
Poin t
1 - 100
Text
LNK
Poin t
1 - 100
Text
LNK
Poin t
1 - 100
Text
LNK
Poin t
1 - 100
Text
Ena ble
LNK
1 - 1
Pag e
Prin t
Gra ph
Prin t
Text
1 - 1
Poin t
LNK
LNK
IrDA
LOGGER
LINK
LOGG ER
LINK
Logger Link
For loggers without two metal contacts to connect
with printer. Including: 88193/88195/88393/88394
/88395/88396/88397/88398/88378.
NOTE:
88375 & 9801printer are not compatible.
Dual stereo phone jack cable is offered in package.
The logger side phone jack size is dia. 2.5 mm.
The printer side phone jack size is dia. 3.5 mm.
NOTE:
All loggers can be programmed through 9801
printer since it has two different contact ports
for all loggers. However, be sure to avoid using
two contact ports at the same time.
Example: DO NOT use logger link port while
operating 8829 logger.
Example: DO NOT use contact port while
operating 88395 logger.
OPERATIONOPERATION
Nex t Page
Cur rent Pa ge
Pre ss to acc ess
the M essag e Page. I f
no da talog ger is
plu gged, " Logge r
Off line" a nd cloc k are
dis playe d on the LC D.
(2) Datalogger is plugging on
(1) Datalogger is not plugged on
While logger is plugging,
the LCD displays the
logger's ID, total record,
rate and unit.
After downloading, the LCD will turn to print page
automatically. Press to print or escape by
pressing . If any error is happened, the LCD
will display the error information.
NOT E:You ca n' t ch ang e th e lo gger se tt in g
in th is MSG mo de.
Download function is
now selected. Press
to execute.
MES SAGE PAG E (MSG)
5
3
Men u
Fee d
Ent er
Up
Dow n
Fee d
Menu
Ente r
Ente r
Menu
Up
Down
Ente r
Ente r
Ente r
Menu
Up
Down
Up
Down
Ente r
Ente r
Ente r
Ente r
Up
Down
Up
Down
Menu
Ente r
Ente r
Up
Down
Menu
The se valu e is base d on prin ting al arm set ting
Whe n selec t Repor t mode, y ou will s ee foll owing :
NOT E: (x 512 /Div) m eans on e divis ion
inc l. 512 re cords .
Whe n selec t Graph m ode, yo u will se e follo wing :
NOT E: (x 16/ Div) me ans one d ivisi on
inc l. 16 rec ords .
The se valu e is calc ulate d from se lecte d pages
Whe n selec t Text m ode, yo u will se e follo wing :
This field allows you to
set the sleep mode of
datalogger. To enable
the sleep mode, select
Enable. Otherwise
select Disable .
SLP M ODE
ID
This field allows you to
set ID of datalogger.
To set the identification,
highlight the ID field and
press to enter
modified mode. Press / to set the first
character of identification then press to save
and enter the next. Max. 8 digits for editing, valid
characters for the identification are 0 to 9, A to Z ,
- , .
NOTE: When logger is removed, this page will
be skipped.
Select right after the last character, press
to save.
LOGGER PAGE (LOG)
Thi s page en able yo u
to pr ogram t he logg er.
This field allows you to set the clock of the logger.
YY, MM, DD, hh, mm, ss stands for year, month,
date, hour, minute, second. Valid values for these
are: YY (2000 to 2099), MM (1 to 12), DD (1 to 31),
hh (0 to 24), mm (0 to 59), ss (0 to 59).
LOG 'S CLOC K SETTI NG
Next LOG Setting
This allows you to set
more datalogger related
parameters, such as:
sample points, rate, unit,
start mode and alarm.
- Point
Point stands for the maximum record. Valid values
: 1000, 2000, 4000, 8000,12000, 16000 (You won't
see all of the points due to the printer will recognize
the available max. points of each datalogger)
-Unit
Unit stands for the unit of
temperature. Valid unit is °C or °F
-Mode
Mode stands for the start
mode of loggers. Valid
modes are: Immediate,
Magnetic, Schedule,
On-line, Key Start,
Repeat.
-Rate
Rate stands for the
sampling interval. Valid
value are 1 to 7200
seconds.
1. Immediate stands for starting right away.
2. Magnetic means you need to use magnet to
slide over the rear side of logger to start.
3. Schedule means logger will start at preset date
& time. The schedule time must be edited.
4. On-line means logger should connect to PC
while logging, so the logging point capacity
is unlimited and data are sent to PC real time.
5. Key Start means you could press the button to
start or stop the logger. In "non-logging" status,
press key for 1sec. to turn on/off the logger as
temp. monitor. Press key for 2 seconds to start/
stop the logging. Once stopping logging, you
could not press key to activate logging, it's
needed to use printer/PC to set the logger again.
6. Repeat means logger will auto-start again after
downloading the data to printer or PC.
Immediate
Magnetic
Schedule
On-line
Key Start
Repeat
8812 8/882 8
/882 9
8813 /8814
/881 5
8833/34 /35 /
88335/3 45
/355
Alarm Settin g
Ala rm Type :
%RH H i :
%RH L o :
%RH
This field allows you to set the Temp. or Humidity
alarm thresholds of logger. Logger red LED will
flash while over alarm
limit.
-Al arm Set ting
Cho ose the p arame ters
(Ai r or Ext. o r%RH)
fir st befo re sett ing the
val ue.
Vali d va lu e for Ai r te mp .
/Ex t. Temp ./RH% a re:
10 11
13
12
14
15
16
SLP M ode
LOG 's Clock Setti ng
Nex t LOG Sett ing
LNK
SLP M ode
Enab le
LOG 's Clock Setti ng
Nex t LOG Sett ing
LNK
SLP Mo de
Ena ble
Nex t LOG Set ting
LOG 's Cloc k Setti ng
SET TING CL OCK
MM-D D-YY hh :mm:s s
-2 5- 0 3 13 :4 4 : 59
0 4
LNK
LNK
SLP M ode
Ena ble
LOG 's Cloc k Setti ng
Nex t LOG Set ting
LNK
Poin t : 1000
o
Rate : 10 Unit : C
Mod e : Immed iate
Nex t LOG Setti ng
Poin t : 1000
o
Rate : 10 Unit : C
Mod e : Sched ule
xx-x x-xx x x:xx:x x
Nex t LOG Setti ng
LNK
LNK
LNK
CONTENT
(Ex : 1-10)
(Ex : 200-1 000)
the m ost pag e
wit hin rec orded p oint
This field allows you to select data range in Graph
and Text printing mode. To select: Highlight the
page or point field and press to enter.
Mode : Report
Content : ( Blank )
Mode : Graph
Content : Page
xx - xx
Mode : Text
Content : Point
xx - xx
Press / to set the data range. Press
to save or press to escape without
saving.
Valid printing ranges are depended on the data of
logger.
One page includes 1000 temperature and humidity
(if available) records.
The n ext pag es show t he exam ples at
Rep ort, Tex t, G ra ph pr in ti ng m ode .
9
88193/8 8195
88393 /8839
4/883 95
88396/3 97/
398
88378
Ente r
Ente r
Up
Down
Menu
Up
Ente r
Down
Ente r
Ente r
LNK
CFG
MSG
PC < > Logger
PC < Printer
PC CONNECTION
USB1.0
USB1.0
PC LINK (LNK)
Thi s print er can co nnect
wit h PC via US B.
Sel ect the f uncti on as
"LN K". Two PC C om mu nic at io n in clu de d in
"LN K" .
Use / t o se le ct t he ne ed ed
fun ction t hen pre ss to con firm an d enter.
Whi le sele cting , y ou only c an
dow nload t he stor ed data t o PC. Thi s is a n on e
way c ommun icati on. Und er Prin ter to PC ,
"Lo gger Se tting " is disa bled. Af ter dow nload ing
PC < Printer
the s tored d ata to so ftwar e, you ca n use thi s
sof tware t o revie w and ana lyse th e store d data.
Whi le sele cting , y ou c an u se t he
pri nter as a r egula r inter face to s et & down load
the l ogger t hroug h PC. Thi s is a t wo w ay
com munic ation s o the pri nter wo rks lik e 8818P,
882 8P, 882 9P, 882 4P inte rf ac e. Un der thi s
fun ction , "Logg er Sett ing" wi ll not be d isabl ed.
PC < > Logger
PC < Printer
PC < > Logger
Thi s print er has
sto rage ca pacit y for
4 log gers an d then
dow nload t he data t o
PC. B eside s, 9801 c an
als o be trea ted as
sta ndard i nterf ace to
upl oad the c omman d
fro m PC to log ger or to
dow nload t he data
fro m logge r to PC.
4 LOGGER’S MEMORY
Pri nter ca n store 4 l ogger s' data . Befor e each
pri nting , uploa ding an d downl oadin g, it is
nee ded to hi ghlig ht LOGG ER 1 .. or LO GGER 4
fil e numbe r and act ivate t he sele cted st orage
fil e.
DOW NLOAD ING
If yo u want to s tore
mor e than on e logge r,
sel ect the f ile num ber
is im porta nt. To load
mor e than on e logge r
wit hout se lecti ng
ano ther fi le numb er,
the L OGGER 1 w ill be
ove rwrit e.
Whe n execu te the do wnloa d comma nd (see
pag e5), "L OG STO Se tt in g" wi ll d is pl ay on t he
LCD .
LOG STO Setting
1 LOGGER1
2 LOGGER2
3 LOGGER3
4 LOGGER4
The f ile ind icato r
poi nts to cu rrent
sto rage fi le. Afte r
dow nload ing, th e ID of eac h datal ogger w ill
rep lace th e origi nal fil e name.
LOG STO Setting
LNK
1 Your own ID
2 LOGGER2
3 LOGGER3
4 LOGGER4
PRI NTING & U PLOAD ING TO PC
Sam e as exec uting d ownlo ad comm and,
"LO G STO Set ti ng " wil l di sp la y on th e LC D.
Sel ect a sui table f ile num ber and p ress
to co nfirm .
Pre ss /
key t o highl ight th e file
num ber and p ress
to co nfirm .
TROUBLE SHO OTINGTROUBLE SHO OTING
1).
Probl em: Pr ess to ru n prin t comma nd
but ski p to MSG p age wit h noth ing
print ed.
Reaso n: Bat tery ha s less e nergy.
Solut ion: O pen the r ear ba ttery c over t o repla ce
with ne w batt ery ( ).
NOTE: Alk alin e batte ry is be tter.
4pcs AAA
Whe n scree n displ ays "Lo w Batte ry”
,t ho ug h you m ight st ill pri nt whil e
"Lo w Batte ry" is sh own, st rongl y
rec ommen d to repl ace bat terie s right
awa y.
24
2).
Probl em: Pr ess to ru n prin t comma nd
but not hing d ispla yed an d no any
infor mati on.
Pap er Jam !
Ple ase Cle ar Pape r !
Pre ss to
con tinue ...
3).
Probl em: Pr ess , but n ot wor king
Low B atter y !
Reaso n: Pap er is jam med.
Solut ion: C lear pa per ja mmed in t he pri nter.
Reaso n: Pap er is jam med.
.
Solut ion: C lear pa per ja mmed in t he pri nter.
4).
Probl em: Lo w Batte ry dis play on L CD
Reaso n: Pow er is not e noug h for ope rati on.
Solut ion:
Electronic Characteristics:
a) Power : DC9V 500mA or
Alkaline AAA 1.5V × 4
(Recommend Alkaline)
b) Consumption :
< 3.2 A : Peak value when printing
< 300 mA : Average value when printing
0.5 ~ 2 mA: Quiescent
< 80 uA : Power down (Typ.: 40 uA)
c) Auto power off after 5 min. of inactivity
o o
d) Operating Temperature : 0 C ~ 50 C
Printing characteristics:
a) Voltage compensating to stabilize the contrast
of printing.
b) While paper jam, printer will stop feeding to
protect printer hand.
c) Feed paper
d) Printing Contrast : 1 ~ 9
e) Print type by report, graphic or text.
(Font : Roman 8 )
f)
g)
h)
LCD C ontra st : 1~9
The rmo-p aper : 58 mm x 20M ( le ngth)
Dim ensio n : 120mm x 1 50mm x 48 m m
( L x W x T )
SPECIFICATIONSPECIFICATION
WARRANTY & RETURN AUTHO RIZATIONWARRANTY &
Autho riza tion mu st be ob taine d from t he
suppl ier be fore re turn ing ite ms for a ny reas on.
When re quir ing a RA (Ret urn Auth oriza tion ),
pleas e incl ude dat a rega rding t he def ectiv e
reaso n, the m eters a re ret urned a long w ith goo d
packi ng to pr event a ny dam age in sh ipme nt and
insur ed aga inst po ssib le dama ge or lo ss.
Proof o f purc hase is r equi red for w arra nty
repai rs. Warranty i s void if the met er has been
opene d.
The met er is wa rrant ed to be f ree fro m defe cts
in mate rial a nd work mans hip for a p erio d of one
year fr om the d ate of pu rcha se. Thi s warra nty
cover s norm al oper atio n and doe s not co ver
batte ry, misus e, abu se, alt erat ion, ta mper ing,
negle ct, im prope r main tenan ce or da mage
resul ting f rom lea king b atter ies.
18
19
21
20
22 23 24
NOT E: The ca libra tion of 8 8335~ 88355
cou ld only b e set by so ftwar e inste ad of
980 1 print er.
NOT E: Pres s to exit P C commu ni-
cat ion mod e.
MSG
Air H i:-40 t o 185 Air Lo : -40 to 18 5
Ext . Hi:-4 0 to 212 Ex t. Lo:- 40 to 212
%RH H i:0 to 10 0 %RH Lo: 0 to 100
NOTE: Low value isn't allowed to exceed high
alarm setting.
-DATE/TIME SETTING
To edit the clock of printer. Valid values are:
YY(2000 to 2099), MM(1 to 12), DD(1 to 31),
hh(0 to 24), mm (0 to 59), ss(0 to 59).
LCD C ont:
Bau drate : 9600
Date : MM-D D-YY
Date /Time S ettin g:
5
PRN
-LCD CONTRAST
To select the printer LCD contrast from 1 to 9.
-BAUDRATE
This field indicates the baudrate of communication.
It is fixed at 9600. Press to skip.
-DATE
To select the format of date. There are: MM-DD-YY
, DD-MM-YY, YY-MM-DD.
CONFIGURATION (CFG)
You can set the configuration of the printer.
SET TING CL OCK
MM-D D-YY hh :mm:s s
-2 5- 0 3 13 :4 4 : 59
0 4
17
201 3.08 ve r.3
Down
Down
Up
Ente r
Menu
Down
Up
Ente r
Ente r
Ente r
Ente r
Feed
Ente r
Pre ss to
con tinue ...
Ente r
Loading...