The warning decal shown here has been applied in
the location shown. If the decal is missing or
illegible, call the telephone number on the front
cover of this manual and request a free replacement decal. Apply the decal in the location
shown. Note: The decal may not be shown at
actual size.
REEBOK and the Vector Logoare registered trademarks and service marks of Reebok. This product is
manufactured and distributed under license from Reebok International.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise cycle before using your exercise
cycle. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.
2. Use the exercise cycle only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise cycle are adequately informed of all precautions.
4. The exercise cycle is intended for home use
only. Do not use the exercise cycle in a commercial, rental, or institutional setting.
5. Keep the exercise cycle indoors, away from
moisture and dust. Place the exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the exercise cycle to mount, dismount, and use it.
6. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
7. Keep children under the age of 12 and pets
away from the exercise cycle at all times.
8. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise cycle. Always wear
athletic shoes for foot protection.
9. The exercise cycle should not be used by
persons weighing more than 250 lbs.
(113 kg).
10. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. Always keep your back straight while using
the exercise cycle; do not arch your back.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
3
BEFORE YOU BEGIN
ongratulations for selecting the new REEBOK
C
310 exercise cycle. Cycling is one of the most effective exercises for increasing cardiovascular fitness,
building endurance, and toning the entire body. The
B 310 exercise cycle offers an impressive array of
R
features to let you enjoy this healthful exercise in the
convenience and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
Backrest
®
B
R
Pulse Sensor
Water Bottle Holder*
odel number and serial number before contacting
m
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
To avoid a registration fee for any service needed
under warranty, you must register the exercise
cycle at www.reebokservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Upright Knob
Seat
Handle
Pedal/Strap
Wheel
Leveling Foot
Game Controller
Handlebar
*No water bottle is included
4
M8 x 19mm Button
Screw (77)–4
M8 x 16mm Button
Screw (54)–6
M8 Split
Washer (55)–14
M4 x 16mm
Round Head
Screw (80)–4
M6 Washer
(44)–7
M10 x 63mm Bolt Set (62)–1
M8 x 50mm Button
Screw (52)–4
M6 x 38mm Button
Screw (72)–3
M6 x 42mm Button
Screw (81)–4
ASSEMBLY
To hire an authorized service technician to assemble the exercise cycle, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the pack-ing materials. Do not dispose of the packing materials until assembly is completed. In addition to the included
tools, assembly requires a Phillips screwdriver, an adjustable wrench, and
rubber mallet.
a
As you assemble the exercise cycle, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number
following the parentheses is the quantity needed for assembly. Note: Some small parts may have been pre-
assembled. If a part is not in the hardware kit, check to see if it has been pre-assembled.
1. Orient the Left Front Stabilizer (15) with the
Wheel (17) positioned as shown. Attach the Left
Front Stabilizer to the left side of the Frame (1) with
three M8 x 16mm Button Screws (54) and three M8
Split Washers (55).
Attach the Right Front Stabilizer (not shown) to
the right side of the Frame (1) in the same way.
1
17
5
15
55
55
54
54
1
2. While another person lifts the rear of the Frame (1),
attach the Rear Stabilizer (16) to the Frame with
four M8 x 50mm Button Screws (52) and four M8
plit Washers (55).
S
2
1
16
3. Tighten the Upright Knob (7) into the Frame (1).
4. While another person holds the Upright (2) near the
Frame (1), use the wire tie in the Upright to pull the
Upper and Main Wire Harnesses (42, 43) through
the Upright. See the inset drawing. Tie the wire tie
to the ends of the Wire Harnesses. Then, pull the
other end of the wire tie upward out of the top of the
Upright.
3
4
Avoid pinching
and damaging
7
the wires
2
55
52
55
52
1
42
43
Attach the Upright (2) to the Frame (1) with an
M10 x 63mm Bolt Set (62). Be careful to avoid
pinching the Wire Harnesses (42, 43).
62
1
62
Wire Tie
42, 43
6
. The Console (4) requires four “D” batteries (not
5
included); alkaline batteries are recommended.
IMPORTANT: If the exercise cycle has been
exposed to cold temperatures, allow it to warm
o room temperature before inserting batteries
t
into the Console. If you do not do this, the con-
ole displays or other electronic components
s
may become damaged. Remove the battery cover
from the back of the Console. Next, insert four batteries into the battery compartment; make sure that
the batteries are oriented as shown by the diagram inside the battery compartment. Then, reat-
tach the battery cover.
The Console (4) can also be operated with an
optional power adapter (not included). To purchase
a power adapter, call the telephone number on
the front cover of this manual. To avoid damaging the console, use only a manufacturer-supplied power adapter. Plug one end of the power
adapter into the jack on the Console; plug the other
end into an outlet installed in accordance with all
local codes and ordinances.
5
Batteries
atteries
B
Battery
4
Cover
6. While another person holds the Console (4) near
the Upright (2), connect the console wire harnesses
to the Upper and Main Wire Harnesses (42, 43).
Insert the excess wire downward into the Upright.
Attach the Console (4) to the Upright (2) with four
M4 x 16mm Round Head Screws (80). Be careful
to avoid pinching the Wire Harnesses (42, 43).
6
Avoid pinching and
damaging the wires
80
80
2
4
42
43
Console
Wire
Harnesses
7
7. Attach the Seat (9) and the Backrest Bracket (3) to
he Seat Bracket (11) with four M6 x 42mm Button
t
Screws (81) and four M6 Washers (44) as shown.
Start all four Button Screws before you tighten
any of them.
7
9
11
3
44
44
81
81
8. Attach the Backrest (8) to the Backrest Bracket (3)
with three M6 x 38mm Button Screws (72) and
three M6 Washers (44). Start all three Button
Screws before you tighten any of them.
8
8
3
44
72
44
44
72
8
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.