Reebok RBCCEL5906.0 User Manual
Model No. RBCCEL5906.0
www.weslo.com
Visit our website at
www.jumpking.com
Visit our website at
www.imagefitness.com
Visit our website at
www.reebokfitness.com
Visit our website at
erial No.
S
Serial Number
Decal (on top
of the frame)
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, please call:
USER'S MANUAL
1-888-936-4266
Mon.–Fri. 8h00 until 17h00 EST
(excluding holidays).
customerservice@iconcanada.ca
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ELLIPTICAL EXERCISER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
REEBOK and the Vector Logo are registered trademarks and service marks of Reebok. This product is
manufactured and distributed under license from Reebok International.
2
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual before
using the elliptical exerciser.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
in-home use only. Do not use the elliptical
exerciser in a commercial, rental, or institutional setting.
4. Place the elliptical exerciser on a level surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical exerciser
indoors, away from moisture and dust.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
8. Wear appropriate exercise clothing when
using the elliptical exerciser. Always wear
athletic shoes for foot protection.
Always hold the handlebar or the upper body
arms when using the elliptical exerciser.
10. Keep your back straight when using the elliptical exerciser; do not arch your back.
11. If you feel pain or dizziness while exercising, stop immediately and cool down.
12. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
13. When you stop exercising, allow the pedals
to slowly come to a stop. The elliptical exerciser does not have a free wheel; the pedals
will continue to move until the flywheel
stops.
14. The decal shown on page 4 has been placed
on the elliptical exerciser in the indicated
location. If the decal is missing or illegible,
call the telephone number on the front cover
of this manual and order a free replacement
decal. Apply the replacement decal in the
location shown.
9. Always hold the handlebar when mounting
dismounting the elliptical exerciser.
or
WARNING:Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
REV–B
209489 & 210125
ongratulations for selecting the new REEBOK
C
545 elliptical exerciser. The RL 545 elliptical exerciser
s an incredibly smooth exerciser that moves your feet
i
in a natural elliptical path, minimizing the impact on
your knees and ankles. And the unique RL 545 features adjustable resistance and a state-of-the-art console to help you get the most from your exercise.
Welcome to a whole new world of natural, ellipticalmotion exercise from REEBOK.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
Upper Body Arm
Fan
Handlebar with Pulse Sensor
®
L
R
ions after reading this manual, please see the front
t
cover of this manual. To help us assist you, please
ote the product model number and serial number
n
before contacting us. The model number is
RBCCEL5906.0. The serial number can be found on
a decal attached to the elliptical exerciser (see the
front cover of this manual for the location of the
decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Bookrack
Console
BACK
Water Bottle Holder*
Upright
Pedal Cushion
Wheel
Pedal
Pedal Leg
RIGHT SIDE
Leveling Foot
*No water bottle is included
4
ASSEMBLY
M4 x 16mm
Screw (82)–6
M4 x 22mm
Screw (92)–2
M4 x 25mm
Screw (69)–2
M8 x 25mm Patch
Screw (73)–10
M8 x 19mm Patch
Screw (81)–4
M6 x 20mm Patch
Screw (75)–4
M6 Split
Washer (72)–2
Small M8
Washer (71)–2
Large M8
Washer (70)–2
M10 Nylon
Locknut (85)–4
Bolt Set (67)–2
M10 Split
Washer (87)–4
Wave Washer
(91)–2
M6 x 13mm
Shoulder
Screw (93)–2
M8 x 19mm
Shoulder
Screw (86)–2
lace all parts of the elliptical exerciser in a cleared area and remove the packing materials. Do not dispose of
P
the packing materials until assembly is completed.
In addition to the included tools, assembly requires an adjustable wrench and a rubber
mallet .
See the drawings below to identify the small parts needed for assembly. The number in parentheses below
each drawing is the key number of the part, from the PART LIST on page 25; the number following the key
number is the quantity needed for assembly. Note: Some small parts may have been preassembled. If a
part is not found in the parts bag, check to see if it has been preassembled.
1. Identify the Front Stabilizer (63), which has Wheels
(27) attached to one side. Attach the Front Stabilizer
to the front of the Frame (1) with four M8 x 25mm
Patch Screws (73).
5
1
73
27
63
73
73
1
2. Attach the Rear Stabilizer (24) to the rear of the
rame (1) with four M8 x 25mm Patch Screws (73).
F
2
1
73
73
24
3. Remove the four M10 Nylon Locknuts (85) and the
four M10 Split Washers (87) from the welded bolts
near the front of the Frame (1).
While a second person holds the Upright (2), connect the Upper Wire Harness (15) to the Lower Wire
Harness (39).
Align the holes in the bracket on the lower end of the
Upright (2) with the welded bolts on the Frame (1).
Lower the Upright,
Harness (15) and the Lower Wire Harness (39) up
into the Upright, until the welded bolts are fully
inserted into the bracket. Be careful to avoid
pinching and damaging the Wire Harnesses.
Place the four M10 Split Washers (87) onto the welded bolts on the Frame (1). Then, tighten the four M10
Nylon Locknuts (85) onto the welded bolts.
feeding the Upper Wire
3
85
87
2
Be careful to
avoid pinching
and damaging the
Wire Harnesses
(15, 39) during
this step.
Bracket
15
39
1
Welded
Bolts
4. Feed the Upper Wire Harness (15) up through the
indicated hole in the Console Bracket (3).
Console Bracket to the Upright (2) with four M8 x
19mm Patch Screws (81).
pinching and damaging the Upper Wire Harness.
Attach the Water Bottle Holder (13) to the Upright (2)
with two M4 x 22mm Screws (92). Note: The water
bottle holder is designed to be used with your own
water bottle.
Be careful to avoid
Attach the
4
81
3
Hole
15
2
13
92
6
5. While another person holds the Handlebar (4) near
the Upright (2), feed the Pulse Sensor Wire (14) into
he Upright and out of the indicated hole in the
t
Console Bracket (3). Attach the Handlebar to the
pright with two M6 x 13mm Shoulder Screws (93)
U
and two M6 Split Washers (72). Be careful to
avoid pinching and damaging the Pulse Sensor
Wire.
5
Hole
3
93
4
1
2
72
4
6. The Console (8) requires four “D” batteries (not
included); alkaline batteries are recommended.
Press the indicated tab on the battery cover and
remove the cover. Press four batteries into the battery clips;
ed as shown by the markings inside of the battery clips. Then, reattach the battery cover.
7. Insert the Bookrack (7) into the slots in the Console
(8). Attach the Bookrack to the Console with two M4
x 25mm Screws (69).
and damaging the wires in the Console.
make sure that the batteries are orient-
Be careful to avoid pinching
6
8
Batteries
Battery
Cover
7
7
8
8. While another person holds the Console (8) near
the Console Bracket (3), connect the Pulse Sensor
Wire (14) and the Upper Wire Harness (15) to the
corresponding wires on the Console.
Insert all excess wiring down into the Upright
(2). Attach the Console (8) to the Console Bracket
(3) with four M4 x 16mm Screws (82). Be careful to
avoid pinching and damaging the Pulse Sensor
Wire (14) and the Upper Wire Harness (15).
69
8
8
Console
ires
W
82
15
3
2
14
82
7
9. Insert the Pivot Axle (21) into the Upright (2), and
center the Pivot Axle. Apply a generous amount of
he included grease to both ends of the Pivot Axle
t
and to the flat side of an Upright Bushing (20).
9
2
Identify the Left Upper Body Arm (5), which is
marked with a decal. Insert the Upright Bushing (20)
into an Upright Spacer (19). Turn the Upright
Spacer so that the semicircular cutout is at the top,
and slide the Upright Spacer onto the post on the
Left Upper Body Arm.
Slide the Left Upper Body Arm (5) onto the Pivot
Axle (21). Attach a Pivot Spacer (17) to the Left
Upper Body Arm with an M4 x 16mm Screw (82).
Turn a Pivot Endcap (16) so that the rectangular
cutout is at the bottom. Using a rubber mallet, tap
the Pivot Endcap into the Pivot Spacer.
Slide a Small M8 Washer (71) onto an M8 x 19mm
Shoulder Screw (86), and finger tighten the Shoulder
Screw into the Pivot Axle (21).
Attach the Right Upper Body Arm (6) in the
same manner. Tighten both M8 x 19mm Shoulder
Screws (86).
10. Apply a small amount of grease to the axle on the
left Crank Arm (40).
10
71
86
16
82
5
9
1
17
Post
20
21
Grease
6
Identify the Left Pedal Leg (28), which is marked
with a decal. Slide the Left Pedal Leg onto the axle
on the left Crank Arm (40). Slide a Wave Washer
(91) and a Large M8 Washer (70) onto an M8 x
25mm Patch Screw (73), and tighten the Patch
Screw into the axle.
Washer is on the end of the axle before tightening
the Patch Screw.
Snap a Pedal Cushion (74) around the Left Pedal Leg
(28) onto a Cushion Bracket (46). Make sure that the
arrow on the Pedal Cushion is pointing to one of the
numbers on the Left Pedal Leg and that the number
shows through the window in the Cushion Bracket.
Assemble the Right Pedal Leg (not shown) in the
same way.
Identify the Left Pedal
1.
1
with a decal. Attach the Left Pedal (35) to the Left
Pedal Arm with two M6 x 20mm Patch Screws (75)
as shown.
Attach the Right Pedal (not shown) to the Right
Arm (not shown) in the same way.
Pedal
Make sure that the Wave
Arm (33), which is marked
1
1
74
Window
33
46
73
Grease
28
40
91
70
75
35
8
12. Set the Left Pedal Arm (33) on the left Pedal Cushion
(74), and hold the end of the Left Pedal Arm inside of
he bracket on the Left Pedal Leg (28).
t
old a Plastic Pedal Arm Spacer (65) between the
H
Left Pedal Leg (28) and the Left Pedal Arm (33).
Insert the long part of a Bolt Set (67) through the Left
Pedal Leg, the Plastic Pedal Arm Spacer, and the
Left Pedal Arm.
Apply a film of the included grease to the long part of
the Bolt Set (67). Lift the Left Pedal Leg (28), and
hold the lower end of the Left Upper Body Arm (5)
inside of the bracket on the Left Pedal Arm (33).
Insert the long part of the Bolt Set through the Left
Upper Body Arm. Hold another Plastic Pedal Arm
Spacer (65) between the Left Pedal Arm and the Left
Pedal Leg, and insert the long part of the Bolt Set
through these parts. Tighten the short part of the Bolt
Set into the long part.
Attach the Right Pedal Arm (32) in the same way.
13. Make sure that all parts are properly tightened before you use the elliptical exerciser. Note: Some
hardware may be left over after assembly is completed.
12
5
65
67
Grease
65
32
33
67
28
74
HOW TO INSTALL THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR
The elliptical exerciser is now fully assembled. If you purchase the optional chest pulse sensor (see
page 21), follow the steps below to install the receiver included with the chest pulse sensor.
1. See assembly step 7 on page 7, and remove the two
M4 x 25mm Screws (not shown) and the Bookrack (7).
Next, look under the Console (8) and locate the three
indicated screws (not shown). Remove the three
screws. Do not remove the screws attaching the
Console to the Console Bracket (not shown).
2. Carefully lift the top of the Console (8) as shown. Using
the two small screws included with the chest pulse sensor, attach the receiver to the indicated plastic posts on
the Console. Make sure that the receiver is turned
exactly as shown. Connect the wire on the receiver to
the indicated wire on the Console.
See step 1 above. Lower the top of the Console (8).
Make sure that no wires are pinched. Reattach the
top of the Console with the three screws removed in
step 1. See assembly step 7 on page 7, and reattach
the Bookrack (7) with the two M4 x 25mm Screws (not
shown). Note: The remaining wires included with the
chest pulse sensor may be discarded.
1
2
Screws
8
Screws
7
8
W
Receiver
Posts
ire
9
Loading...