Red-M Blade User Manual

Download

Red-M Blade

Bluetooth Clip-on for Palm Vx

User Guide

980-959-03

Red-M Blade - Bluetooth Clip-on for Palm Vx Getting Started Guide

Table of contents

Introduction..............................................................................5

About the Red-M Blade ................................................................5

Getting started ...........................................................................6

Red-M Blade overvie w...............................................................7

Bluetooth services .......................................................................7

Additions to Palm Vx menus .........................................................7

Managing Bluetooth devices ..........................................................8

Palm network service settings .......................................................9

Installing the Red-M Blade software .......................................11

Before you begin ....................................................................... 11

To install the Red-M Blade software .............................................11

Additional software on the Red-M Blade CD ..................................11

Attaching the Red-M Blad e ...................................................... 12

Detaching the Red- M Bla de ....... ..............................................13

Configuring a connection to the Internet via a mobile phone ..14

Before you begin ....................................................................... 14

To configure your Palm Vx to connect to a mobile phone ................ 19

Configuring a Bluetoo th-enabled LAN connection....................21

Before you begin ....................................................................... 21

To configure your Palm Vx to connect to LAN Access infrastructure ..21

Configuring Blueto o th H o tSync operations..............................23

Configuring a HotSync operation with a computer .......................... 23

Configuring a HotSync operation via a Bluetooth-enabled LAN .........25

Configuring a remote HotSync operation via a mobile phone ...........27

Technical support and con ta ct information..............................30

Regulatory information ...........................................................31

Europe (EEA) ............................................................................31

North America ..........................................................................31

Power supply information ...........................................................32

Red-M User License and Limited Warranty Agreement ............35

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Introduction

About the Red-M Blade

The Red-M Blade is a simple and innovative accessory that adds a new level of flexibili ty to your Palm

you are in the off ic e or on the road you can enjoy hassle-free, wireless connection to personal , corpo rate and public data.

With a Red-M Blade and a Bluetooth you can access the Internet, and send and receive email. The connection is c a ble-free and there is no longer any need to carefull y line up your Palm Vx handheld with your mobile phone or PC to achieve a line-of-sight, infrared connection.

Vx handheld. Whether

enabled mobile phon e,

You can perform a wireless HotSync

operation to your lap to p via your Red-M Blade instead of the usual Palm cradle. When away from the office, you can perform a remote HotSync operation via your mobile phone. The Red-M Blade also enables you to interact with other Bluetooth-enabled Palm Vx handhelds.

If your office has Bluetooth infrastructure installed, you can use your Palm Vx with the Red-M Blade attached in meeting rooms and other Bluetooth enabled areas to maintain connection to the corporate intr anet or Internet, to send and receiv e emails, and to update your calendar.

Getting started

To us e your Red-M Blade, do the following:

1. Install the software

For ins t ructions on how to install Red-M Bla d e software on your Palm Vx, see Installing the Red-M Blade software on page 11.

2. Attach the Red-M Blade

For instructions on how to attach the Red-M Blade, see Attaching the Red-M Blade on page 12.

3. Configure your Palm Vx for Bluetooth services

Configure the software to connect with any or all of the followin g Blu etooth-enab le d devices:

• a mobile phone for access to the Internet or to perform remote HotSync ope rations with your computer via your corporate network (where you have a remote access dial-up facility). For instructions, see Configuring a

connection to the Internet via a mobile phone on page 14 and Configuring a remote HotSync operation via a mobile phone on page 27.

• a laptop computer or PC to perform HotSync operations. For instructions, see Configuring a HotSync operation with a computer on page 23.

• an Access Point on your local area network (LAN) for connection to LAN intranet and Internet services and to perform HotSync operations with a designated computer. For instructions, see Configuring a Bluetooth-enabled

LAN connection on page 21 and Configuring a HotSync operation via a Bluetooth-enabled LAN on page 25.

• another Bluetooth enabled Palm Vx handheld for playing games. There are games and associated documentation included on the Red-M CD.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Red-M Blade overview

This section lists the Bluetooth services provided by the Red-M Blade. It describes the additional options and menu items that you will find on your Palm Vx handhel d fo llowing installati on of the Red-M Blade software. It also explains how to use device categorie s and the informat ion used when you connect to the Internet.

Bluetooth services

To enable the Red-M Blade to connect to a number of different types of devices, Red-M software supports three Bluetooth services:

• LAN Access Use this service to connect to Bluetooth network

infrastructure.

• Dial-up Networking Use this service to connect to a Bluetooth-enabled mobile

phone.

•Serial Use this service to perform a Ho tSync operation with a

computer or to connect to another Palm Vx handheld to play games.

Additions to Palm Vx menus

When you have completed the software installation, you will find some additional items on your Palm Vx handheld System, Prefs

menus.

•the option Bluetooth has been added to the pick list in the upper-right corner of the System, Prefs screen. Fro m the Bluetooth preferences screen you can set the default device categories for each Bluetooth service which enables you to automate your Bluetooth connections (see Managing Bluetooth de vi c es below).

• four Blue to ot h co nnec t ion c onf ig ur at io n s (Bt LAN Access, Bt Dial-up, Bt Serial and Bt Serial Host) have been added to the

Available Configurations list on the System, Prefs, Connections screen. Choose Connections from the pick list described

above to access this screen.

• a new network service called B t LAN Access on the System, Prefs, Network screen (choose Network from the pick list). This is the service that is us ed to connect to a Bluetooth - enabled local ar ea network.

Managing Bluetooth devices

Before your Red-M Blade can connect to any other Bluetooth device it must first discover other Bluetooth devices within range.

You can discover all Bluetooth-enabled devices within range of your Red-M Blade by performing a ‘device discovery’. Once discovered, you can move devices into categories such as Phones, Computers and Access Points, for easy management and automate d c onnection to eac h Bluetooth s er vice.

Using categories

Each Bluetooth service (Dial-up, LAN access and Serial) has a default device category assigned to it. Whenever a Bluetooth connection is requested, your Palm Vx handheld will automatically connect to a device in the Bluetooth service’s default category. For example, if you place your mobile phone into the Phones category, you can specify that each time you make a Bluetooth Dial-up networking connection, your Palm Vx handheld should connect to a device in the Phones category. Similarly, if you put a Red-M Access Point into the Access Points category, you can specify that each time your Palm Vx handheld makes a LAN Access connection, it should connect to a device from the Access Points category.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

If a category contains multiple devices, the Red-M Blade will connect to t he first av ailable dev ice. This is useful if, fo r example, there are several LAN Access Points in your office to which you can connect.

File devices into categories using Bluetooth preferences screen 2.

When you have installed the Red-M Blade software, the Phones, Access Points and Computers categories will already be available for you to use. You can add, delete and merge categories as required using the Edit categories option from the pick list on this screen.

Set the default device category for each Bluetooth service by using Bluetooth preferences screen 1. Y ou can also set the default device category to Prompt. If you do this, when the Palm Vx handheld needs to make a Bluetooth connection, you will be aske d which category and / or device to which you want to connect.

Palm network service settings

When an application (for example, a WAP browser) on the Palm Vx handheld wants to us e the network, the netw ork s ervice that will be used to make the connection will be the service that is displayed on the System, Prefs, Network screen.

Each network service has a Connection setting, which determines the physical network connection used. Connections are managed through th e System, Prefs, Connection screen.

Red-M Blade software adds a network service setting called Bt LAN Access, with Connection set to Bt LAN Access. This is the network service that is used when you connect to Bluetooth LAN Access Points.

If you are connecting to an intranet or the Internet via a Bluetooth-enabled mobile phone, you must add a new network service and set Connection to Bt Dial-up. For more information, see Configuri ng a connection to the Internet via a mobile phone on page 14.

When a network service usin g Bt LAN Access or Bt Dial-up connection is used, the device used to make the connection will

be one that is stored in the default device category for LAN Access or Dial-up respectively.

Your System, Prefs settings determine which Bluetooth-enabled device and which network service will be used to make the connection. The diagram below illustrates how the information on the Bluetooth and Network screens from System, Prefs settings is used when internet connection is made.

Figure 1: Use of Network and Bluetooth preferences when making an Internet

connection

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Installing the Red-M Blade software

Before you begin

Before you begin, you w ill need:

• a Palm Vx handheld running Palm OS® 3.5.x or late r. To find out which version of the Palm OS Applications icon then the menu icon , and from the App

menu choose Info, then tap Version. Upgrades for earlier Palm OS versions are availabl e from the Palm web site at www.palm.com. Red-M Blade software is not compatible with Palm V models .

• a PC running Microsoft Windows 95, 98, NT4, ME or 2000 Professional with a CD-ROM drive (f or s oftware ins tallation). Your PC must have Palm Vx Desktop software installed and have the Palm cradle connected.

you are running, tap the

• a Red-M CD (supplied).

To install the Red-M Blade software

1. Insert the Red-M CD into your PC; the Red-M Blad e install menu is displ aye d.

2. Click on Install Software for Red-M Blade. If more than one Palm Vx user is installed on your PC, you will also need to specify which user you wish to receive the files.

3. Click OK to exit the install menu.

4. Install the Red-M Blade software on your Palm Vx by mounting the Palm Vx in its cradle (wit hout the Red-M Blade attached) and performing a HotSync operation.

5. When the Hot S ync op er atio n co mplet es, yo u w ill b e asked to reset your Palm Vx handheld. Do so.

Additional software on the Red-M Blade CD

Some additional Palm Vx applications have been included on the Red-M Blade CD which you may wish to install on your Palm Vx handheld to enhance your Bluetooth f unctionality and ease of connection. Adobe Acrobat Reader is also included, which is a PC application required to read t he do cumentation that is on the CD .

To install any or all of these applications, select ‘Other Software’ on the Red-M Blade install menu, select your application and then follow the on-screen instructions. Documentation for these applications is included on the CD.

Attachin g th e Red-M B la de

Before attaching the Red-M Blade, note down its Bluetooth address, wh ic h is printed on its front. Dependin g on your Bluetooth security settings, this may be required to identify the Red-M Blade when connecting to Bl uetooth servic es.

The Red-M Blade has a 10-pin connector at the bottom, which is identical to the one on your Palm handheld serial cradle. To attach the Red-M Blade, simply slide your Palm handheld onto the Red-M Blade's co nnector as you would for mo unting in its serial cradle. Once connected, push the Palm handheld back towards the Blade until you hear a ‘click’.

Note: With the Red-M Blade attached, you can perform a Bluetooth HotSync operation but not the usual serial HotSync operation using the cradle. If you need to perfor m a serial HotSync operation with the cradle attached, simply detach the Blade from your Palm handheld. The Palm handheld will recharge its batteries as normal when placed in the serial cradle with the Red-M Blade attached.

Figure 2: Attaching the Red-M Blade

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Detaching the Red-M Blade

To detach the Red-M Blade, turn the unit over so that it is face down, and push the latch at the back to the left to unclip the Palm Vx handheld. Pull the Palm Vx handheld up and away from the Red-M Blade.

Figure 3: Pushing the latch on the back of the Red-M Blade

Figure 4: Detaching the Red-M Blade

Configuring a connection to the Internet via a mobile phone

Before you begin

Before you begin, you w ill need:

• a Palm Vx handheld with a Red-M Blade attached (see page 12) and Red-M software installed (see page 11).

• a Bluetooth-enabled mobile phone:

• if you have a Nokia 6210, see To configure you r P al m Vx

to connect to a Nokia 6210 with bl uetooth battery on page 14.

• if you have and Ericsson T39m or R520m, see To

configure your Palm Vx to connect to an Ericsson T39m or R520m on page 16.

• if you have any other Bluetooth-enabled mo bile phone,

see To configure your Palm Vx to connect to a mobile phone on page 19.

• the Bluetooth address and passk ey of your mobile phone. This information may be printed on the mobile phone’s battery label, but the location varies with manufacturer. On some mobile phones you choose your own passkey. Refer to your mobile phone manual for more information.

• an ISP account user name, password and phone number.

To configure your Palm Vx to connect to a Nokia 6210 with bluetooth battery

Configuring your Palm Vx handheld

1. On your Palm Vx handheld, perform a device

discovery:

i. Go to System, Prefs and select Bluetooth

from the pick list.

ii. Tap 2 ( ) to go to Screen 2 (shown);

ensure that the pick list selection is set to All or Unfiled, and then tap Discover.

iii. The Red-M Blade will then find all

Bluetooth-enabled devices in range.

iv. Tap Stop to ha lt the discovery pr o c es s.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

2. Look for the Bluetooth address or name of

your mobile phone in the list of discovered devices. Tap on this address or name to go to the Device Information dialog (shown).

3. In the Device In formation dialog , t a p

-Not set- and enter th e pa s s key of your mobile phone. Tap OK to close the Bluetooth Passkey dialog.

4. Tap Update. T he Red-M Blade will r e tr ieve

the device nam e an d s er vice profiles available; a tick should now be displayed beside Dial-up N etworking.

5. Tap OK to exit th e Device Information dialog

and return to the list of discovered devices.

6. Move your mobile phone into the Phones

category:

i. Tap the checkbox to th e left of the name

of your mobile phone.

ii. Tap Move; in the Move Selected Devices

dialog, select Phones from the drop-down menu. Tap OK to accept the change and close the di a log.

7. Tap 1 to go to Screen 1; ensure that the

Dial-up category is set to Phones.

8. Set up your ISP details: i. From the pick list in the top right-hand

corner, select Network, then tap the Menu icon and tap New.

ii. Give the Service a name - ‘Freeserve’ for

example - and under User Name input the name required by your ISP.

iii. Tap -Prompt- to enter the ISP p a ss wor d ;

if you leave the password setting as

-Prompt- you will be asked t o input the password each time you connect.

iv. Set Connection as Bt Dial-up using the

drop-down list.

v. Enter the ISP ph one number in Phone.

Testing the connection

To tes t the connection, tap Connect in the Network, Prefs screen.

Using the Internet

Now that the IS P and phone s et up is compl ete, when you use an application that requires an Internet connection, the R ed-M Blade will automat ically contact the mo b ile phone which will di al your ISP and give you an Internet connection.

Note: If you subsequently change the network service selected on the System, Prefs, Network screen (for example, if you change to Bluetooth Bt LAN Access service that uses a LAN Access Point on a corporate Bluetooth network), when you want to connect to your mobile phone, you must reset the current network service to the Bluetooth Dial-up service that you added in the above proc edure.

To end the Bluetooth session

To end th e Bluetooth session and th ereby terminate the mobil e phone call, do one of the following:

• switch off the Palm Vx.

•use the Disconnect option (if one exists) in whichever application you are using.

•go to System, Prefs, Network and tap the Disconnect butt on .

To configure your Palm Vx to connect to an Ericsson T39m or R520m

Connecting your Palm Vx handheld to your mobile phone

1. On your mobile phone, sele ct Menu, Extras,

Bluetooth and Discoverable.

2. On your Palm Vx handheld, perform a device

discovery:

i. Go to System, Prefs and select Bluetooth

from the pick list.

ii. Tap 2 ( ) to go to Screen 2 (shown);

ensure that the pick list selection is set to All or Unfiled, and then tap Discover.

iii. The Red-M Blade will then find all

Bluetooth-enabled devices in range.

iv. Tap Stop to ha lt the discovery pr o c es s.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

3. Look for the Bluetooth address or name of

your mobile phone in the list of discovered devices. Tap on this address or name to go to the Device Information dialog (shown).

4. In the Device In formation dialog , t a p

-Not set- and enter a passkey for your mobile phone (a four figure number, for example). Tap OK to close the Bluetooth Passkey dialog.

5. On your mobile phone, sele c t Menu, Extras,

Bluetooth. Select Paired devices, Add device, and Phone accepts.

6. On the Palm Vx handheld, ensu re your

mobile phone is highlighted in the list of discovered devices. From the Preferences pick list, tap Connect. Y our mobile phone will display the prompt : Add to paired devic es ?.

7. On your mobile phone select Yes. Your

mobile phone will now prompt you for th e passkey that you entered on the Palm V x handheld earlier in this procedure.

8. On your mobile phone, enter the pass key

and select Yes. If pairing is successful, you can now edit the name of your Palm Vx on your mobile phone. Your mobile phone adds your paired devices to the Paired List.

9. On your Palm Vx handheld, move your

mobile phon e into the Phones category:

i. Tap the checkbox to th e left of the name

of your mobile phone.

ii. Tap Move; in the Move Selected Devices

dialog, select Phones from the drop-down menu. Tap OK to accept the change and close the di a log.

10. Tap 1 to go to Screen 1; ensure that the

Dial-up category is set to Phones.

11. Set up your ISP details: i. From the pick list in the top right-hand

corner, select Network, then tap the Menu icon and tap New.

ii. Give the Service a name - ‘Freeserve’ for

example - and under User Name input the name required by your ISP.

iii. Tap -Prompt- to enter the ISP p a ss wor d ;

if you leave the password setting as

-Prompt- you will be asked t o input the password each time you connect.

iv. Set Connection as Bt Dial-up using the

drop-down list.

v. Enter the ISP ph one number in Phone.

Testing the connection

To test the connection, tap Connect in the Network, Prefs screen

Using the Internet

To end the Bluetooth session

To end th e Bluetooth session and th ereby terminate the mobil e phone call, do one of the following:

• switch off the Palm Vx.

•use the Disconnect option (if one exists) in whichever application you are using.

•go to System, Prefs, Network and tap the Disconnect butt on .

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

To configure your Palm Vx to connect to a mobile phone

Note: Depending on the manufacturer, you may need to configure your m ob ile phone to be Blueto ot h- enabled. Refer to the documentation that accompanied it for more information.

1. On your Palm Vx handheld, perform a device

discovery:

i. Go to System, Prefs and select Bluetooth

from the pick list.

ii. Tap 2 ( ) to go to Screen 2 (shown);

ensure that the pick list selection is set to All or Unfiled, and then tap Discover.

iii. The Red-M Blade will then find all

Bluetooth-enabled devices in range.

iv. Tap Stop to ha lt the discovery pr o c es s.

2. Look for the Bluetooth address or name of

your mobile phone in the list of discovered devices. Tap on this address or name to go to the Device Information dialog (shown).

3. In the Device In formation dialog , t a p

-Not set- and enter th e pa s s key of your mobile phone. Tap OK to close the Bluetooth Passkey dialog.

4. Tap Update. T he Red-M Blade will r e tr ieve

the device nam e an d s er vice profiles available; a tick should now be displayed beside Dial-up N etworking.

5. Tap OK to exit th e Device Information dialog

and return to the list of discovered devices.

6. Move your mobile phone into the Phones

category:

i. Tap the checkbox to th e left of the name

of your mobile phone.

ii. Tap Move; in the Move Selected Devices

dialog, select Phones from the drop-down menu. Tap OK to accept the change and close the di a log.

7. Tap 1 to go to Screen 1; ensure that the

Dial-up category is set to Phones.

8. Set up your ISP details: i. Select Network, then tap the Menu icon

and tap New.

ii. Give the Service a name - ‘Freeserve’ for

example - and under User Name input the name required by your ISP.

iii. Tap -Prompt- to enter the ISP p a ss wor d ;

if you leave the password setting as

-Prompt- you will be asked t o input the password each time you connect.

iv. Set Connection as Bt Dial-up using the

drop-down list.

v. Enter the ISP ph one number in Phone.

Testing the connection

To tes t the connection, tap Connect in the Network, Prefs screen.

Using the Internet

To end the Bluetooth session

To end th e Bluetooth session and th ereby terminate the mobil e phone call, do one of the following:

• switch off the Palm Vx.

•use the Disconnect option (if one exists) in whichever application you are using.

•go to System, Prefs, Network and tap the Disconnect butt on .

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Configuring a Bluetooth-enabled LAN connection

Before you begin

Before you begin, you w ill need:

• a Palm Vx handheld with a Red-M Blade attached (see page 12) and Red-M software installed (see page 11).

• configured Bluetooth infrastructure (for example, a Red-M 3000AS access serv er running software version 1.3 or later with Access Points connected).

• the name or Bluetooth address of the Access Point or Access Server to which you want to connect and the Bluetooth passkey if one is u sed. For this i nform atio n , ask yo ur syst em administrator.

To configure your Palm Vx to connect to LAN Access infrastructure

1. On your Palm Vx handheld, perform a device

discovery:

i. Go to System, Prefs and select Bluetooth

from the pick list.

ii. Tap 2 ( ) to go to Screen 2 (shown),

ensure that the pick list selection is set to All or Unfiled, and then tap Discover.

iii. The Red-M Blade will then find all

Bluetooth-enabled devices in range.

iv. Tap Stop to ha lt the discovery pr o c es s.

2. In the list of discovered devices, look for the

name or Bluetooth address of each of the Access Points to which you want to connect. Access Points and Access Servers will be categorized as LANs in this list. (Access Servers are treated as Access Points in this procedure.)

3. If your system administrator has given you a

Bluetooth passkey:

i. Tap the Access P oint’s name to go to the

Device Information screen (shown)

ii. Tap -Not set- and enter the passk ey. Tap

OK to exit the Bluetooth Passkey dialog.

4. Move your Access Point into the Access

Points category:

i. Tap the checkbox to th e left of the name

of your Access Point.

ii. Tap Move; in the Move Selected Devices

dialog, select Access Points from th e drop-down menu.

iii. Tap OK to accept the change and close

the dialog.

5. Tap 1. Ensure the LAN Access default

category is set to Access Points.

6. Set the Service type to Bt LAN Access: i. Select Network from the top right-hand

menu.

ii. Set the Service type to Bt LAN Access

using the drop-dow n list that appears on this screen.

iii. The Connection selection should also be

Bt LAN Access.

Now that the Access Point set up is complete, when you use an application that needs a network connection, the Red-M Blade will automatically make a Bluetooth connection to an available Access Point in the Access Points category and give you acce ss to the network.

Note: If you subsequently change the network service selected when you go to System, Prefs, Network (for example, if you change to a Bluetooth dial-up service that uses a mobile phone), when you want to connect to an Access Point, you must reset the current network service to Bt LAN Access.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Configuring Bluetooth HotS ync op erations

You can perform a Bluetooth HotSync operation with your computer using your Red-M Blade in three different ways:

• from your Red-M Bla de directly to a Bluetooth-e nabled laptop or PC.

• from your Red-M Blade via an Access Point on a Bluetoothenabled LAN to a designated computer.

• from your Red-M Blade via a mobile phone connection to a remote access server on your LAN.

Note: to perform a serial HotSync operation using the Palm cradle, you must first detach the Red-M Blade from your Palm Vx.

Configuring a HotSync operation with a computer

Before you begin

Before you begin, you w ill need:

• a Palm Vx handheld with a Red-M Blade attached (see page 8) and Red-M software installed (see page 6).

• a computer with Palm Vx Desktop software and a Bluetooth PCMCIA card or Bluetooth USB device installed.

• the Bluetooth address of the Bluetooth PCMCIA card or Bluetooth USB device. You can find this address by using the Bluetooth cli ent software on your computer.

To configure a HotSync operation with a computer

1. On your Palm Vx handheld, perform a device

discovery:

i. Go to System, Prefs and select Bluetooth

from the pick list.

ii. Tap 2 ( ) to go to Screen 2 (shown),

ensure that the pick list selection is set to All or Unfiled, and then tap Discover.

iii. The Red-M Blade will then find all

Bluetooth-enabled devices in range.

iv. Tap Stop to ha lt the discovery pr o c es s.

2. Look for the Bluetooth address or name of

your computer on the discovered devices list.

3. If you are using Bluetooth authentication: i. Tap the computer’s address or name to

go to the Device Information dialog.

ii. Ent er the passkey here by ta pping -Not

set-.

iii. Tap Update; tap OK to exit the Device

Information dialog.

4. Move your computer into the Computers

category:

i. Tap the checkbox to th e left of the name

of your computer.

ii. Tap Move; in the Move Selected Devices

dialog, select Computers from the dropdown menu.

iii. Tap OK to accept the change and close

the dialog.

5. Tap 1. Ensure that the Serial Port default

category should be set to Computers.

6. Tap the Applications icon then th e

HotSync icon .

7. Your HotSync settings should specify a local

HotSync operation:

i. Tap Local to select the Local tab. ii. Tap the Menu icon and select

LANSync Prefs.

iii. Tap Local HotSync and OK.

8. On the HotSync screen, select Bt Ser i al from

the pick list beneath the HotSync button.

9. Tap the HotSync button. Th e HotSync

operation will begin.

Now that you have configured your Palm Vx handheld to perform a Hotsync operation with a Bluetooth-enabled computer, the next time you want to perform a Hot Sync operati on you only have to tap the HotSync button.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Note: If you are using a PC with a Bluetooth USB device, ensure that the HotSync Manager on your PC is configured to use same serial port as your Bluetooth USB device. To check this, rightclick the HotSync Manager on your PC, select Setup and then the Local tab.

Configuring a HotSync operation via a Bluetooth-enabled LAN

You can perform a HotSync operation from your Palm Vx handheld (with Red-M Blade attached) via an Access Point on a Bluetooth-enabled loca l area network (L AN). The PC that y our Palm Vx will perform the operation with is specified as part of the configuration process.

Before you begin

Before you begin, you w ill need:

• a Palm Vx handheld with a Red-M Blade attached (see page 12) and Red-M software installed (see page 11).

• a computer with Palm Vx Desktop software installed and the name and IP address of this computer, which should be configured to allow network HotSync opera tions.

• configured Bluetooth infrastructure (for example, a Red-M 3000AS access serv er running software version 1.3 or later with Access Points connected).

• to have completed the procedure to connect to LAN Access infrastructu r e on pa ge 21.

To configure a HotSync operation via a Bluetooth-enabled LAN

1. Go to System, HotSync. Tap Modem on the

HotSync screen to select the Modem tab.

2. Tap the Menu icon , select Modem Sync

Prefs, then choose Network and tap OK.

3. Tap the Menu icon , select LANSync P refs

then choose LANSync and tap OK.

4. Tap the Menu icon , select Connection

Setup, ensure Bt LAN Access is selected in the list and ta p Done.

5. Select Bt LAN Access as the ser vice, using

the pick list beneath the HotSync icon. The HotSync screen should no w loo k like the on e shown.

6. Tap the Menu icon , select Primary PC

Setup and enter your HotSync PC’s name in the Primary PC Name fiel d.

• to view th is informatio n, right-click the

HotSync Manager on your PC, select

Setup and the Network tab and the n click TCP/IP Settings.

7. Enter your HotSync PC’s IP address in the

Primary PC Address field.

• to view th is informatio n, right-click the

HotSync Manager on your PC, select

Setup and the Network tab and the n click TCP/IP Settings.

8. Tap the HotSync button. Th e HotSync

operation will begin.

Now that you have configured your Palm Vx handheld to perform a Hotsync operation via a Bluetooth-enabled LAN, the next time you want to perform a Ho tSync operation you only have to ta p the HotSync button.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Note: If your computer has more than one IP address, you will need to ensure that the HotSync Manager is using the correct address. To check this, right-click the HotSync Manager on your PC, select Setup and the Network tab and then cl ick TCP/IP Settings; the IP address displayed here should be the same as the IP address you have entered into the Primary PC Setup on your Palm handheld.

Configuring a remote HotSync operation via a mobile phone

You can perform a HotSync operation from your Palm Vx handheld (with Red-M Blade attached) to a computer co nnected to your company network, via a Bluetooth connection to your mobile phone. T his option will only be available if your company network supports dial-up remote access.

Before you begin

Before you begin, you w ill need:

• a Palm Vx handheld with a Red-M Blade attached (see page 12) and Red-M software installed (see page 11).

• a computer with Palm Vx Desktop software installed.

• a dial-up account on your company netwo r k.

• a Bluetooth-enabled mobile phone.

• the Bluetooth address and passk ey of your mobile phone. Sometimes these are printed on the battery label. You will need these before you can make a Bluetooth connection.

To configure a HotSync operation with a mobil e phon e

1. Follow the instructions to connect to your

mobile phone on page 14 up to and including step 7.

2. Set up your company dial-up details: i. Go to System, Prefs an d from the pick li st

on the upper-right corner of the screen, select Network

ii. Tap the Menu icon and tap New. iii. Giv e the Service a name; this name will

be used to select this service from the Network, Services pi ck list.

iv. Select Bt Dial-up as the connection type

using the Connection drop-down menu.

v. Enter the telephone number of your

company’s dial-up service and your username and password.

vi. Tap OK.

3. Tap the Applications icon then th e

HotSync icon .

4. Tap Modem on the HotSync dialog to select

the Modem ta b.

5. Tap the Menu icon and select Modem

Sync Prefs. Select Network and tap OK.

6. Tap the Menu icon and select LANSync

Prefs. Select LANSync and tap OK.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

7. Ensure that your corporate remote-access

dial-up service is the selected service (this is displayed below the HotSync icon). If you need to change the service selection:

i. Tap the current service selection. ii. On the Prefs, Network screen, tap Service

and select your corporate remote-access dial-up service.

iii. Tap Done.

8. Tap the Menu icon , select Primary PC

Setup and enter your HotSync PC’s name in the Primary PC Name fiel d.

• to view th is informatio n, right-click the

HotSync Manager on your PC, select

Setup and the Network tab and the n click TCP/IP Settings.

9. Enter your HotSync PC’s IP address in the

Primary PC Address field.

• to view th is informatio n, right-click the

HotSync Manager on your PC, select

Setup and the Network tab and the n click TCP/IP Settings.

10. Tap the HotSync butt on. The HotSync

operation will begin.

Now that you have configured your Palm Vx handheld to perform a Hotsync operation via your mobile phone, the next time you want to perform a HotSync operation in this way you only have to tap the HotSync button.

Technical support and contact information

For Red-M B lade support information, visit the Red-M website at www.red-m.com/blade

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Regulatory information

The following regulatory statements apply to the Red-M Blade - Bluetooth Clip-on for Palm Vx.

Europe (EEA)

This product is designed to connect to "Bluetooth" compatible radio interfaces us in g the 2.4 GHz frequency ba nd in all E EA Member States with the excep tion of Fr ance wher e the use of the follow ing frequen cies is restricted:

2.4000 - 2.4460 GHz Use Excluded - Military Band

2.4540 - 2.4835 GHz Limited to indoor video applications

[Member States of the EEA are: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Liechtenstein, Netherlands, Norway, Port ugal, Spain, Sweden, Switzerland, United Ki ngdom.]

North America

This equipment co mplies with part 15 of the FCC rules. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Operation is subje c t to the following two conditio n s : (1) this de vic e may not cause interfer ence, and (2) thi s device must accept any in terfe rence, including in terference that may cause undesired operation of the devi ce. This device has been designed to operate with an antenna having a maximum gain of 0 dB. Antenna having a higher gain is strictly prohibited pe r re gulations of Industry Canada. The req uir ed antenna impedance is 50 ohms. To reduce poten tial rad io in t er fe re n ce to other users, th e an te nn a type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. To prevent radio interference to the licensed service, this device is intended to be op era te d indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is sub jec t to lic e ns ing . IMPORTANT NOTE: To comply with FCC RF expo s ure co mp lia n ce requireme nts , th e foll ow in g ante nna installation and de vice operating configuratio ns mu st b e sa tisf ied- The devi ce and i ts ant enn a must n ot b e co-located or operating in conjunction with any other antenna or transmitter.

Power supply information

English

CAUTION: Only use this produc t wi th a po wer sour c e that m eets the "Limited Power Source" requirements of IEC 60950 or equivalent safety standards . Use the power supply provided (if applicable) or contact RedM for a list of suita ble po we r so u rc e s .

Dansk

ADVAR SEL: Dette produkt må kun anvendes sammen med strømki lder, der opfylde r kravene vedrørende "Limited Power Source" i IEC 60950 eller tilsvarende sikkerhedsstandarder. Anvend den medfølgende strømforsyning (hvis muligt), eller kontakt Red-M og få en liste over godkendte strømkilder.

Français

ATTENTION: n'utilisez ce produit qu'avec une source d'énergie conforme à la norme IEC 60950 en matière de « source d'énergie limitée », ou autre norme de sécurité équivalente. Utilisez l'alimentation en courant fournie (si applicable) ou bien contactez Red-M pour obtenir une liste des sources d'énerg ie adéquates.

Español

PRECAUCIÓN: Emp lee este producto únicamente con una fuente de alimentación que cumpla la norma de seguridad IEC 60950 de alimenta ci ón limitada, o equivalen te . Utilice la fuente de al im en ta c ión suministrada, si es el caso, o consulte a Red-M para obtener una lista de fuentes de alimentación apropiadas.

Português

Advertência: Utilize este produ to apenas com uma fonte de energia que respeite os requisitos definidos em "Fontes de Energia Limitadas" da norma IEC 60950 ou dos padr ões de seg urança equivalent es . Utili ze a fonte de alimentação fornecida (se aplicável) ou contacte Red-M para obter uma lista de fontes adequadas.

Suomi

MUISTUTUS: Kä ytä tä tä tuo te tta vain sella ise n virt a lähte e n yhte yd es s ä, joka täyttää standardin 60950 "rajoitetun virtalähteen" tai muiden vastaavien sta nda r di en asettamat turvallisu usvaatimukset. Käytä toimitettua virtalähdettä (jos asianmukaista) tai ota yhteys RedM:ään sopivien virtalähteiden luettelon saamiseksi.

Flemish

OPGELET: gebruik dit product enkel met een voe di ngsbr on di e voldoet aan de "Minimum voedings bron"-verei sten van IEC 60950 of evenwaardige veiligheidsvoorschriften. Gebruik bij horende voedingsbron (indien deze geschikt is) of neem contact op met RED-M voor een lijst van geschikte voedin gs br onnen.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Nederlands

WAARSCHUWING: Gebruik dit product alleen met een voedingsbron die voldoet aan de "Minimum voedingsbron"-vereisten van IEC 60950 of evenwaardige veiligheidsvoorschriften. Gebruik de bijbehorende voedingsbron (indien van toepassing) of neem contact op met Red-M voor een lijst van geschikte voedingsbronnen.

Deutsch

WARNUNG: Verwenden Sie dieses Produkt nur mit einer Stromquelle, die die Anford er u ngen bezüglich "b egrenzter Stro m qu e ll en" gemäß IEC 60950 oder entsprechender Sicherheitsnormen erfüllt. Verwenden Sie das im Liefer umfang ent haltene Net zteil ( sofern zu treffen d), oder f ordern Sie bei Red-M ein e Liste de r ge eigneten Stro mq u e lle n a n .

Svensk

FÖRSIKTIGT! Denna produkt får bara användas med en effektkälla som uppfyller kraven för "Begränsad effektkälla" i IEC 60950 eller motsvarande säkerhetsnormer. Använd medföljande effektkälla (i förekommande fall) eller begär en lista över lämpliga effektkällor från Red-M.

Íslenska

VARÚÐ: Notið þessa vöru eingöngu með aflgjafa sem stenst kröfur í kaflanum um "aflgjafa með takmarkað afl" í IEC 60950 (ÍST EN 60950) eða sambærilegra öryggisstaðla. Notið aflgjafann sem fylgir (ef viðeigandi) eða fáið lista yfir nothæfa aflgjafa hjá umboðsaðila vörunnar.

Norsk

FORSIKTIG: Dette produktet skal bare bruk es med en strømkilde som tilfredsstiller kravene til "Begrenset strømkilde" i IEC 60950 eller tilsvarende sikkerhetsstandard. Bruk den medfølgende strømforsyningen (hvis en slik finnes) eller kontakt Red-M for å få en oversikt over passende str ømkilder.

λληνικά

ΠΡΟΣΟΧΗ: Χρησιµοποιήστε αυτό το προϊόν µόνο µε πηγή ενέργειας που είναι σύµφωνη µε την οδηγία του IΕC 60950 περί «Περιορισµένης Πηγής Ενέργειας» ή αντίστοιχων προδιαγραφών ασφαλείας. Χρησιµοποιήστε την πηγή ενέργειας που παρέχεται (αν είναι κατάλληλη) ή επικοινωνήστε µε την Red-M για να σας προµηθεύσει µε κατάλογο συµβατών πηγών ενέργειας

Italiano

ATTENZIONE: Utilizza re que sto prodotto solo con sorge nti di alimentazione che soddisfano i requisiti di sicurezza IEC 60950 o equivalenti. Utilizzare l'alimentatore fornito (ove applicabile) o contattare Red-M per ottenere un elenco delle sorgenti di alimentazione adeguate.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

Red-M User License and Limited Warranty Agreement

IMPORTANT: THIS IS A LEGAL AGREEMENT BETWEEN YOU AND RED-M.

BY INSTALLING, COPYING OR OTHERWISE USING THE SOFTWARE PRODUCT (AS DEFINED BELOW), YOU AGREE TO BE BOUND BY THE TERMS OF THE "RED-M USER LICENSE AND LIMITED WARRANTY AGREEMENT " BELOW. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RED-M ARE UNWILLING TO LICENSE THE SOFTWARE PRODUCT TO YOU. IN SUCH EVENT, YOU MAY NOT USE OR COPY THE SOFTWARE PRODUCT, AND YOU SHOULD PROMPTLY RETURN THE UNUSED PRODUCT EITHER TO RED-M OR AN AUTHORIZED RESELLER FOR A REFUND. THE "SOFTWARE PRODUCT" INCLUDES COMPUTER HARDWARE AND SOFTWARE, EMBEDDED FIRMWARE, THE ASSOCIATED MEDIA, ANY PRINTED MATERIALS, AND ANY "ONLINE" OR ELECTRONIC DOCUMENTATION.

RED-M User License and Limite d Warranty Agreement

This Red-M User License and Limited Warranty Agreement, as modified by the "Addi tional License Provisions" set forth below or in the documentation accompanying this product (collectively, the "Agreement in this package (if any) (the "Hardware use the Red-M software de scribed below (the "Software terms and conditions below. You agree that all other hardware subsequently supplied to you by Red-M or Red-M's authorized agents, distributors or resellers will be subject to the terms, conditions, limited warranties and remedies of this Agreement, unless you are bound by terms of a different Red-M agreement distributed with such hardware.

Red-M License

The Softwa re lice nsed by th is Agre ement i nclud es all the s oftw are on any distribution media supplied to you within this package (and includes any software accompanying, pre-pr og rammed or pre-loaded within any Hardware supplied). You agree that all other software and upgrades, enhancement s or imp rove m en ts to any of the Software subseque ntl y supplied t o you by Red-M or Red-M's au thorized age nts, distribu tors or resellers on any distribution media or via any form of electronic distribution will be subject to the terms, conditions, limited warranties and remedi es of th i s Ag re e m en t , u nle ss yo u a re bou n d by te rm s of a different Red-M license distributed with such software, upgrades, enhancements or improvements. The Software is owned by Red-M or its licensors and is protected by United States and other country copyright laws and by international treaty provisions. Red-M or its licensors retain ownership of the Software and no rights are granted to you other than a license to use the Software on the terms expressly set forth in this Agreement. This Agreement imposes certain restrictions on your use of the Sof tware .

"), grants you the right to use the Red-M hardware enclosed

") and a non-exclusi ve license to

"), under the

Subject to any limitation in the Additional License Provisions, if any, you may:

• use only one copy of the Software on any accompanying Hardware;

• use the Software in only machine-readable form

• make copies of the Software for back-up purposes, but you may not use the back-up copies other th an as a replacement for the original copy. You must incl ude all copyright and ot her notices included on the Software on any copie s you make;

• make copies of the documentation, the written materials or electronic user information accompanying the Software and/or the Hardware (if any) supplied by Red-M, but only for use within the organization to which you belong , and only for the purposes of installing and using the Software and the Hardware. You must include all copyright and other notices included on the materials on any copies you make.

Except as otherwise permitted pursuant to this Agreement, you may not:

• make any copies of any of the Software other than for back-up purposes as permi tte d a bove ;

• sublicense, rent, loan or lease the Software or documentation to another, except where you are leasing Red-M Hardware with which or for which th e Softw are was supp lied (if any) to an end user, and in such circumstan ces, you ag ree on beha lf of t he end user to be bou nd by all of the terms of this Agreement;

• decompile, disassemble, reverse engineer, or modify in any way, any of the Hardware, Software or other Red-M Products , e xce pt to the extent that this restriction is expressly prohibited by applicable law;

• transfer or assign your rights to use the Software except upon a transfer of any associated Red -M hardware

• transfer or assign your rights to use the Software except upon a transfer of any associated Red-M hardware with which or for which the Software was supplied (if any), and in such circumstances, you agree on beha l f of the en d u ser to be bound by all of the ter m s of this Agreement;

• use the Software in a life-support or safety system or in any other application in which the failure of the Sof twa r e or Har dwa re co uld create a situation where p ersonal in jury or death may oc cur, without the prior approval of Red-M, an d in any eve nt, you s ha ll take fu ll responsibility for any such use.

• use the Software for any purpos e othe r tha n as pe r mi tte d in this Agreement.

You acknowledge and agree that:

• if you upgrade any older Red-M products ("Upgraded Products any of the Software, then you a gr ee th at this Ag re em e nt will thereafter apply to such Upgraded Products.

• if you obtain any other Red-M software and are not bound by a written Red-M user license agreement, then you agree that you are using such software in accordance with the applicable terms of this Agreement;

") with

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

• Red-M or its licensors retain ownership of the Software and no rights are granted to you other tha n a lice ns e to use the So ftwa r e on the terms expressly set forth in this Agreement; the underlying design of all Red-M hardware and the structure, sequence, organizat ion and source co de of a ll Red -M so ftware are valuable trade se c r e ts of Red M or its licensors ;

• the export of the Softw are and Hardware may be restricted by the export control laws of the Unite d States of America and other countries. You agree to compl y wit h all su ch a pp lic a bl e e xp ort control laws;

• without limiting the rights that the licensors or suppliers of Red-M otherwise have to protect their intellectual property rights, each of such licensors o r suppl ie rs are thi rd part y be nefi ciar ie s of thi s Agr eement for their respective products and may have the right to enforce such terms against you;

• by using the Hardware and / or Soft w are y ou h er eby gi v e exp li cit co nsent for Red-M to process your personal data ("Personal Data") for administrative, billing, marketing and support purposes, to include the transf er of P erson al Data insi de and outs ide of the European Economic Area (including, but not limited to, the USA). Y ou agree that Red-M may collect Personal Data fr om , or th rou gh your use of, the Hardware and/or Software supplied to you by Red-M and from information that you or your reseller supplies directly to Red-M. Red-M acknowledges your rights in relation to Personal Data and will have in place appropriate technical and organizational security measures so as to ensure a level of security that is appropriate to the nature of the data that is being processed. You may obtain further information on your rights in relation to Personal Data by contacting Red-M's Data Protection Compliance Officer at Wexham Springs, Framewood Road, Wexham, Slough, SL3 6PJ, UK.

• the Software may conta in or be de ri ved from portions of code an d documentation provided by a third party u nder license to Red-M. Red-M has assum ed resp onsi b ili t y for the se le ctio n of suc h code and documentation and its use in producing and licensing the Software. ALL SUCH THIRD PARTIES DISCLAIMS ALL WARRANTIES WITH RESPECT TO THE USE OF SUCH CODE OR DOCUMENTATION IN THE SOFTWARE, INCLUDING (WITHOUT LIMITATION) ANY WARRANTIES OF SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE.

The limitation of liabilities described in this Agreement also applies to any third-party supplier of code and documentation supplied to you. Red-M and its third-party supplier limitations of liabilities are not cumulative. Such third-party supplier is an intended beneficiary of this section. The Red-M 10 00 AP prod uct co ntai ns s oftw are li ce nsed fr om Pr ecise Softw are Technologies In c. ©Copyright 2000 Prec is e So ftware Technologies Inc . The Red-M 3000 AS product con tains software licensed from Ex tended Systems In c. ©Copyri ght 20 00 Extende d Sys tems Inc. Copyrig ht © 20 00 General Software Inc . All rights res erved. The Software may contain portions of code or other works which are licensed to Red-M under, and are subject to, the GNU GE NE RAL PUBLIC LICENSE, which is repr od uc ed

in the user r ef ere nce gu i de di st rib u ted w it h t he H ard wa re. I n a ccord an ce with the GNU GENERAL PUBLIC LICENSE and subjec t to receiving a request and payment for the costs of performing such source distribution, Red-M shall provide any third party, who so requests, with a machine readable copy of the source code of the works on a medium customar ily use d for so ftwa r e inte rchange: this offe r sh all remain valid for a period of three years from the first customer release of a version of the works. Copyrig h t © 19 89, 1991 Free Software Foundation, Inc. 675 Mass Ave, Cambridge, MA 02139, USA. The Red-M 3000AS product contains software licensed from PHP, freely available from http:// www.php.net/. The PHP License , ver sion 2.2 . Cop yr ig ht © 1999, 2000 The PHP Group. All righ t s res er ved . Co pyright © 1997 Eric Young (eay@mincom.oz.au) All rights reserved. The Red-M 3000AS product contains Qpopper software which, excluding the portions owned by the Regents of the University of California, is Copyright 1993-2000 QUALCOMM Incorporated and code from the software program Popper, which is © Copyright 1989-1991 The Regents of the University of California, All Rights Reserved. Copyright (c) 199 0, 199 3, 19 94, 1995, 1996, 1997, 1998 Sleepycat Software. All rights reserved. Copyright (c) 1990, 1993, 1994, 1995 The Regents of the University of California. All rights reserved. Copyright (c) 1995, 1996 The President and Fellows of Harvard University. All rights reserved. Contains security software from RSA Data Security, Inc Copyright © 1998 and 1990 RSA Data Secur ity Inc. All rights reserved.

• the license granted hereby is effective until terminated. You may terminate this Agreement as to any Software at any time by destroying such Softwar e, the relat ed media, and all relate d back -u p copies and documenta tio n. Up on any violation of any of the provis ion s of this Agreement, your right to use the Software and Hardware (if any) will automatically terminate and you will be obligated to return to Red-M or destroy all of such Software and to cease to use all of such Hardware;

• this Agreement will be governed by the laws of England and Wales, other than its provisions concerning the applicability of laws of other jurisdictions;

• this Agreement is the complete and exclusive statement of your agreement with Red-M with respect to the subject matter hereof and supersedes all prior agreements or communications, written or oral. If any provision of this Agreement is held to be invalid or unenforceable by a court of competent jurisdiction, the remaining provisions of this Agreement shall remain in full force and effect.

Red-M Blade - Bluetooth Clip-on for Palm Vx User Guide

U.S. Department of Defense & U.S. Civilian Agencies

If the comp uter sof tware progr ams or do cumenta tion pr ovided under th is license agre ement are to be utili zed in contracts with or on be ha l f of th e United States of America, its agencies , or its instrumentalities (the "Government" ) , the y s h all be considered and tre a te d a s "commercial computer so ftwa r e" , a s that term is defined in the De partment of Defense Federal Acquis iti on Regula ti on Supplement ("DFARS") Subpa rt

227.72. If the Govern m e nt is the lic e n se e , it shall have only the rights

specified in this license and shall have no greater rights than any other licensee of the commercial computer software or commercial software documentation.

Red-M Limited Warranty

Red-M warrants that under normal use and conditions the products listed below will for the appropriate duration after the date of original purchase from Red-M listed below (each a "Warranty Period") be free from defects in materials and workmanship as follows:

Product Warranty

Red-M Blade - Bluetooth Clip-on for Palm Vx 1 year Red-M 3000AS 1 year Red-M 1000AP 1 year Software Media (if any) 90 days THE SOFTWARE (OTHER THAN SOFTWARE MEDIA, IF ANY) IS PROVIDED "AS IS" WITHOUT ANY WARRANTY. If you believe that you have discovered any covered defect during the applicable Warranty Period, please contact your local authorized reseller or distributor or, if they are unable to help you or you obtained the product directly from Red-M, please contact your local Red-M office directly. If Red-M, or the authorized reseller or distr ibutor, instructs you to return the product please return any Hardware together with the accompanying Software media (including all copies of the Software) (or just the Software media if no Hardware was supplied) freight prepaid to either the author i zed res el le r or di st ribu to r fr om which i t wa s pur ch ased , or to Red-M, as instructed. Please note you may also be asked to provide written docume ntation of your purchase. CUSTOMER REMEDIES:

Red-M's and its lice nsors', suppliers ' , re s ellers' and distributors' entire liability to you, and your exclusive remedy will be, at Red-M's option: (i) repair or replacement of the Software media or Hardware that does not m ee t the Red-M Warranty, or (ii) return of the price paid. All media and Hardware which is replaced will become the property of Red-M. Repla cem e n t pro duc ts ma y be new or re c onditioned. Red-M will have no responsibility, warranty or other obligations whatsoever as a result of: (a) the use of the Hardware, Software media and/or Software in a manner inconsistent with the accompanying manuals and this Ag re e m ent , or (b) any mo difications made to the Hardware or Software, or (c) failure of the Hardware, Software media or Software as a result of accident, abuse or misapplication, or (d) use of Hardware and So ftwa r e wi th pr od uct s n ot read ily commercially availa bl e on the date of the origi nal pu r cha se. Red-M an d its au thor ized distributors or resellers are not responsible for any software, firmware, information or data contained in, or sto red on, any returned ite ms.

NO OTHER WARRANTIES:

THE WARRANTIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES. RED-M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, AND RED-M EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF SATISFACTORY QUALITY, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ACCURACY AND ANY WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. MOREOVER, THE PROVISIONS SET FORTH ABOVE STATE REDM'S ENTIRE RESPONSIBILITY AND YOUR SOLE AND EXCLUSIVE REMEDY WITH RESPECT TO ANY BREACH OF ANY WARRANTY. THIS WARRANTY DOES NOT AFFECT ANY STATUTORY RIGHTS THAT YOU MAY HAVE IF YOU ARE A CONSUMER LIMITATION ON LIABILITY; NO LIABILITY FOR CONSEQUENTIAL DAMAGES: UNDER NO CIRC UM STANCE AND UNDER NO THEORY OF LIABILITY WILL RED-M OR ITS LICENSORS, SUPPLIERS, RESELLERS OR DISTRIBUTORS BE LIABLE FOR COSTS OF PROCUREMENT OF SUBSTITUTE PRODUCTS OR SERVICES, LOST PROFITS, LOST SAVINGS, LOSS OF INFORMATION OR DATA, OR ANY OTHER SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENT AL DAMAGES, ARISING IN ANY WAY OUT OF THIS AGREEMENT OR THE SALE, LICENSE OR USE OF, OR INABILITY TO USE, ANY RED-M PRODUCT (HARDWARE OR SOFTWAR E) OR SERVICE, EVEN IF RED-M HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED W ARRANTY. The warranties, limitations and remedies contained herein allocate risk of Software, Hardware and media breach of warranty or other liability and Red-M's prices reflect the allocation of such risk. Certain jurisdictions restrict the ability to (a) exclude implied warranties, (b) limit or exclude incidental or cons e quential damages, or (c) limit liability impo sed un de r product liability laws. T o the extent any such restrictions apply to you and may not be waived, the foregoing limitations and exclusions may not apply to you. If, notwiths ta nd ing the above claus e s, Red-M is sub jec t to any liability in connection with the Software or Hardware, whether arising from neglig ence, breach of contr act o r otherwi se, R ed-M's li abilit y will n ot exceed the sum paid by you to Red-M for the Hardware and/or Software that did not comply with the Red-M Limited Warranty . This limitation does not apply in the case of personal injury or death if and to the extent prohibited by a pp lic a b le law.

Trademarks Red-M, and the Red-M logo are trademarks, and in some jurisdictions may be registered trademarks, of Red-M (Communications) Ltd. Bluetooth is a trademark owned by Bluetooth SIG Inc USA and used by Red-M under license. Other trademarks appearing in this document are the property of their respective owners.

Additional Provisions: None

Red-M Blade User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual