Safety and Regulatory Information
This section lists required safety, conformity and regulatory
For the latest and updated information, please refer to the ratings
We, Red-M, declare under our sole responsibility that the 3000AS
This equipment is intended to be used in all Member States of the
port of this product and the ISDN network interface as detailed in
information for certain jurisdictions.
plate on the Red-M 3000AS access server.
European Economic Area
United States
Canada
European Economic Area
See the (currently unsigned) Certificate of Conformity. (Requires
Adobe Acrobat Reader.)
is in conformity with the provisions of Council Directive
1999/5/EC on radio equipment and telecommunications terminal
equipment and the mutual recognition of their conformity.
European Economic Area (EEA).
It is intended to be directly connected to BRI ISDN public
telecommunications network interfaces in all EEA Member States
with the exception of Sweden and Norway. In these countries it
may only be indirectly connected behind a device providing
supplementary insulation for a primary circuit between the ISDN
the relevant special national conditions of EN60950: 1992 clause
6.2.1.2.
It is designed to connect to "Bluetooth" compatible radio
interfaces using the 2.4 GHz frequency band in all EEA Member
States with the exception of France where the use of the
following frequencies is restricted:
2.4000 - 2.4460 GHz - Use Excluded - Military Band
2.4540 - 2.4835 GHz - Limited to indoor video
applications
[Member States of the EEA are: Austria, Belgium, Denmark,
Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Liechtenstein, Netherlands, Norway, Portugal,
Spain, Sweden, Switzerland, United Kingdom.]
top
United States
This equipment complies with part 15 of the FCC rules. Any
changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the
equipment.
This equipment complies with Part 68 of the FCC rules. On the
rear of this equipment is a label that contains, among other
information, the FCC registration number for this equipment. If
requested, the following information must be provided to the
telephone company.
FCC Registration Number: RDMGTB-40289-XD-N
Ringer Equivalence Number (REN): N/A
Facility Interface Code (FIC): Connects to 02IS5 via
NT1/NTCE
Service Order Code (SOC): 6.0Y
USOC Jack Type: Connects via NT1/NTCE using
RJ11C, RJ21X or RJ49C
An FCC compliant telephone cord and modular plug is provided
with this equipment. This equipment is designed to be connected
to the telephone network or premises wiring using a compatible
modular jack that is Part 68 compliant. See Installation
Instructions for details.
If this equipment, 3000AS, causes harm to the telephone
network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if
advance notice isn't practical, the telephone company will notify
the customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is
necessary.
The telephone company may make changes to its facilities,
equipment, operations or procedures that could affect the
operation of the equipment. If this happens the telephone
company will provide advance notice so you can make the
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, 3000AS, for repair
or warranty information, please contact Red-M, 860 Hillview Ct,
Suite 260, Milpitas CA 95035, USA (+1 800 606 2343). If the
equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the
To conform with FCC rules regarding RF exposure, this equipment
Department does not guarantee the equipment will operate to the
themselves, but should contact the appropriate electric inspection
equipment until the problem is resolved.
Connection to party line service is subject to state tariffs.
(Contact the state public utility commission, public service
commission or corporation commission for information.)
It is strongly suggested that an AC surge arrestor is installed in
the AC outlet to which this equipment is connected.
CAUTION: To reduce the risk of fire, use only No. 26 AWG or
larger telecommunication line cord.
should be installed a minimum of 20cm away from any
personnel.
top
Canada
NOTICE: The Industry Canada label identifies certified
equipment. This certification means that the equipment meets
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The
user's satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. The
customer should be aware that compliance with the above
conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause
to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural
areas.
Caution: Users should not attempt to make such connections
authority, or electrician, as appropriate.
Operation is subject to the following two conditions: [1] this
This device has been designed to operate with an antenna having
To reduce potential radio interference to other users, the antenna
isotropically radiated power (EIRP) is not more than that required
device may not cause harmful interference, and [2] this device
must accept any interference, including interference that may
cause undesired operation of the device.
a maximum gain of 0dB. An antenna having a higher gain is
strictly prohibited per regulations of Industry Canada. The
required antenna impedance is 50 ohms.
type and its gain should be so chosen that the equipment
for successful communication.
To prevent radio interference to the licensed service, this device
is intended to be operated indoors and away from windows to
provide maximum shielding. Equipment (or its transmit antenna)
that is installed outdoors is subject to licensing.
top
Return to the Support main page.
Loading...