Red Lion N-Tron Series 1000 Hardware Manual

N-Tron® Series 1000

Industrial Gigabit Media Converters
& Gigabit Ethernet Switches

Hardware Guide | August 2016

COPYRIGHT

Copyright, © 2015-2016 Red Lion Controls, Inc.

20 Willow Springs Circle

York, PA 17406

All rights reserved. Red Lion, the Red Lion logo and N-Tron are registered trademarks of Red Lion Controls,
Inc. All other company and product names are trademarks of their respective owners.

The information contained in this document is subject to change without notice. Red Lion makes no warranty
of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability
or fitness for a particular purpose. In no event shall Red Lion be liable for any incidental, special, indirect or
consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions
in this manual or the information contained herein.

CONTACT INFORMATION :

AMERICAS

Inside US: [phone]
Outside US: [phone]
Hours: 8am-6pm Eastern Standard Time
(UTC/GMT -5 hours)

ASIA-PACIFIC

Shanghai, P.R. China: [phone] x767
Hours: 9am-6pm China Standard Time
(UTC/GMT +8 hours)

EUROPE

Netherlands: [phone]
France: [phone]
Germany: [phone]
UK: [phone]
Hours: 9am-5pm Central European Time
(UTC/GMT +1 hour)

Website: www.redlion.net

Email: [e-mail]

Table of Contents Revised 2016-08-30

Drawing No. LP1001

Table of Contents

Preface

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Environmental Impact Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Toxic Emissions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Trademark Acknowledgments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Release Notes and Document Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Publication History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Document Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Additional Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

General Safety Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Electrical Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Environmental Safety Cautions and Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Hazardous Location Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Laser Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Section 1 Introduction and Specifications

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Model 1002MC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Key Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

Product Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Model 1002MC Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Model 1003GX2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Key Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

Product Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

Model 1003GX2 Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

Model 1005TX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8

Key Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-9

N-Tron® Series 1000 Hardware Guide i

Revised 2016-08-30 Table of Contents
Drawing No. LP1001

Product Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-9

Model 1005TX Regulatory Approvals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Model 1008TX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Key Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Product Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Model 1008TX Regulatory Approvals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Model 1008TX-POE+. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Key Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Product Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Model 1008TX-POE+ Regulatory Approvals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Section 2 Installation

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

Installing/Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

DIN-Rail Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Power Connection (Top View). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

N-Tron Series Switch Grounding Techniques for 1000 Series . . . . . . . . . . . . . . . . . . . . . . . . 2-19

RJ45 Connector Crimp Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

Section 3 Operation and Maintenance

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

Model 1002MC, 1003GX2, 1005TX Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

Model 1008TX Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23

Model 1008TX-POE+ Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Verify/Troubleshoot Cable Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

ii N-Tron® Series 1000 Hardware Guide

Preface Revised 2016-08-30

Drawing No. LP1001

Preface

Disclaimer

Portions of this document are intended solely as an outline of methodologies to be followed during the
maintenance and operation of N-Tron® Series 1000 equipment. It is not intended as a step-by-step guide or a
complete set of all procedures necessary and sufficient to complete all operations.

While every effort has been made to ensure that this document is complete and accurate at the time of release, the
information that it contains is subject to change. Red Lion Controls is not responsible for any additions to or
alterations of the original document. Industrial networks vary widely in their configurations, topologies, and traffic
conditions. This document is intended as a general guide only. It has not been tested for all possible applications,
and it may not be complete or accurate for some situations.

Users of this document are urged to heed warnings and cautions summarized at the front of the document, such as
electrical hazard warnings.

Compliance Information



It is recommended that the owner of this equipment determine and ensure conformance with any specific and
applicable local regulations.

Part 15 of the Federal Communications Commission (FCC) - A Rules: Interference

Every effort has been made to ensure that this equipment is designed to comply with the limits for a Class A digital
device, as described in the FCC Rules.

This product complies with Part 15 of the FCC-A Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful Interference

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Operation of this device in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.



Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulations. Operation is subject to the following two conditions; (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.

Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des
règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas
causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris
l'interférence qui peut causer l'opération peu désirée.

N-Tron® Series 1000 Hardware Guide iii



Revised 2016-08-30 Preface
Drawing No. LP1001

Environmental Impact Statement

Red Lion equipment contains no hazardous materials as defined by the United States Environmental Protection
Agency (USEPA). Red Lion recommends that all failed product be returned to Red Lion for failure analysis and
proper disposal.

Toxic Emissions

Red Lion equipment releases no toxic emissions.

Trademark Acknowledgments

Ethernet is a registered trademark of Xerox Corporation. All other company and product names are trademarks of
their respective owners.

Release Notes and Document Updates

The hard copy and electronic media versions of this document are revised only at major releases and therefore,
may not always contain the latest product information. As needed, Documentation Notes and or Product Bulletins
will be provided between major releases to describe any new information or document changes.

The latest online version of this document and all product

http://www.redlion.net/documentation.

at

updates can be accessed through the Red Lion web site

Publication History

The following information lists the release history of this document.

ISSUE/REVISION RELEASE DATE CONTENT DESCRIPTION

Revised 2014-01-23 January 2014 Document Updates

Revised 2015-03-17 March 2015 Added 1008TX Model, Format Changes

Revised 2015-03-24 March 2015 Format Changes to Cover, Page Header and Tables

Revised 2016-08-30 August 2016 Add 1008TX-POE+ model

Related Documents

Visit the Technical Resources page on the Red Lion website at the following link to view available documents
related to this product.

http://www.redlion.net/documentation/red-lion-documentation

Document Comments

Red Lion appreciates all comments that will help us to improve our documentation quality. The user can submit
comments through the Red Lion Customer Service. Simply email us at

[e-mail]

Additional Product Information

Additional product information can be obtained by contacting the local sales representative or Red Lion through the
contact numbers and/or e-mail addresses listed on the inside of the front cover.

iv N-Tron® Series 1000 Hardware Guide

Preface Revised 2016-08-30

Drawing No. LP1001

Warnings and Cautions

Warnings apply to situations where personal injury or death may result.

Cautions apply to where reduced function or damage to equipment may result.

General Safety Cautions and Warnings

CAUTION: If the N-Tron series equipment is used in the manner not specified by Red Lion, the
protection provided by the equipment may be impaired.

ATTENTION: Si
la protection fournie par l'équipement peut être compromise.

CAUTION: Do not perform any services on the unit unless qualified to do so. Do not substitute
unauthorized parts or make unauthorized modifications to the unit.

ATTENTION:
substituer pièces non autorisées ou de modifications non autorisées de l'appareil.

l' N-Tron série équipement est utilisé d'une manière non spécifiée par Red Lion,

Ne pas effectuer de services sur l'appareil s'il n'est pas qualifié pour le faire. Ne pas

CAUTION: Do not operate the equipment in a manner not specified by this manual.

ATTENTION: Ne pas faire fonctionner l'équipement d'une manière non spécifiée par ce manuel.

WARNING: Install only in accordance with Local and National Codes of authorities having

jurisdiction.

ALERTE: Installer uniquement, conformément aux codes locau
compétence.

Electrical Safety Warnings

WARNING: Do not work on equipment or cables during periods of lightning activity.

ALERTE: Ne pas travailler sur le matériel ou les câbles pendant les périodes d'activité de la

foudre.

x et nationaux des autorités ayant

N-Tron® Series 1000 Hardware Guide v

Revised 2016-08-30 Preface
Drawing No. LP1001

WARNING: Properly ground the unit before connecting anything else to the unit. Units not

properly grounded may result in a safety risk and could be hazardous and may void the warranty.
See the grounding technique section of this Hardware Guide for proper ways to ground the unit.

ALERTE: Correctement à la terre de l'unité avant tout raccordement à l'unité. Unités pas
correctement mise à la terre peut entraîner un risque de sécurité et pourraient être dangereux et
peut annuler la garantie. Voir la section technique de mise à la terre de ce mode d'emploi des
moyens appropriés à la masse de l'appareil.

WARNING: This equipment must be used with a Listed UL Industrial Power Supply.

ALERTE: Cet équipement doit être utilisé avec une

alimentation UL Listed industrielle.

WARNING: This equipment (1005TX,1008TX and 1008-TXPOE+) must be used with a Listed UL
Class 2 Power Supply.

ALERTE: Cet équipement (1005TX,1008TX and 1008-TXPOE+) d

oit être utilisé avec une alimen-

tation UL Listed Classe 2.

WARNING: A Recognized or Listed fuse, rated maximum 3A, minimum 30VDC, must be installed
on the line side of the device.

ALERTE:

Un fusible reconnu ou classé, classé 3A maximale, 30VDC minimum, doit être installé

sur le côté de la ligne de l'appareil.

WARNING: Use 110°C or higher rated copper wire, (0.22Nm) 2 lb/in tightening torque for field
installed conductors.

ALERTE: Utilisez 110°C ou nominale supérieure fil de cuivre, (0,22 Nm) 2 lb/pouce couple de
serrage pour le champ installé conducteurs.

WARNING: Do not operate the unit with the end plates removed, as this could create a shock or
fire hazard.

ALERTE : N

e pas faire fonctionner l'unité avec les plaques d'extrémité retiré, ce qui pourrait créer

une décharge électrique ou un incendie.

CAUTION: Observe proper DC Voltage polarity when installing power input cables. Reversing
voltage polarity can cause permanent damage to the unit and voids the warranty.

ATTENTION: Respecter la polarité correcte de tension DC lors de l'installation des câbles
d'alimentation d'entrée. Inversion de polarité de tension peut causer des dommages permanents à
l'appareil et annule la garantie.

vi N-Tron® Series 1000 Hardware Guide

Preface Revised 2016-08-30

Drawing No. LP1001

Environmental Safety Cautions and Warnings

CAUTION: This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or
non-hazardous locations only.

ATTENTION: Cet équipement est adapté pour une utilisation dans la classe I, Division 2, Groupes
A, B, C et D ou non dangereux endroits seulement.

WARNING: Expl

osion Hazard – Substitution of components may impair suitability for Class I,

Division 2.

ALERTE - Risque d'explosion - Remplacement d'un composant peut empêcher la conformité de
Classe I, Division 2.

WARNING: Do not operate the equipment in the presence of flammable gases or fumes. Operat­ing electrical equipment in such an environment constitutes a definite safety hazard.

ALERTE : Ne pas utiliser le matériel en présence de gaz ou de vapeurs inflammables. L'utilisation
de matériel électrique dans un tel environnement constitue un danger certain.

WARNING – Explosion Hazard – Do not connect or disconnect any connections while circuit is
live unless area is known to be non-hazardous.

ALERTE - Risque d'explosion - Ne pas brancher ou débrancher les connexions lorsque le circuit
est sous tension sauf si la zone est connue pour être non dangereux.

WARNING: Disconnect the power and allow to cool 5 minutes before touching.

ALERTE: D

éconnectez le câble d'alimentation et laisser refroidir 5 minutes avant de la toucher.

Hazardous Location Warning

WARNING (1005TX ,1008TX and 1008TX-POE+ only): This equipment is open-type device and
is meant to be installed in an enclosure suitable for the environment that is only accessible with
the use of a tool.

ALERTE (1005TX ,1008TX and 1008-TXPOE+ uniquement): Cet équipement est ouvert de type
périphérique et est destiné à être installé dans un boîtier adapté à l'environnement qui n'est
accessible qu'avec l'utilisation d'un outil.

N-Tron® Series 1000 Hardware Guide vii

Revised 2016-08-30 Preface
Drawing No. LP1001

Laser Safety Warning

CAUTION (1002MC and 1003GX2 only): CLASS 1 LASER PRODUCT. Do not stare into the
laser.

ATTENTION (1002MC et 1003GX2 uniquement): PRODUIT LASER CLASSE 1. Ne pas regarder
dans le laser.

viii N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

Drawing No. LP1001

Section 1 Introduction and Specifications

Introduction

The N-Tron® Series 1000 Unmanaged Industrial Gigabit Ethernet Switches and Media Converters are housed in
ruggedized enclosures, and provide Category-5 compliant 10/100/1000Base-T connections for high performance
network design. The 1000 series switches support high speed layer 2 switching between ports.

Fiber models utilize IEEE compliant LC duplex connectors for fiber optic communications in a convenient SFP
(Small Form Pluggable) modular design. All 10/100/1000Base-T ports utilize RJ45 shielded connectors.

• The 1002MC is a two port unmanaged media converter that converts 10/100/1000Base-T copper to

1000BaseSX/LX SFP port.

• The 1003GX2 is a three port unmanaged Gigabit switch that offers one 10/100/1000Base-T copper port and

two 1000BaseT/SX/LX SFP ports.

• The 1005TX is a five port unmanaged Gigabit switch that offers five 10/100/1000Base-T copper ports.

• The 1008TX is an eight port unmanaged Gigabit switch that offers eight 10/100/1000Base-T copper ports.

• The 1008TX-POE+ is an eight port unmanaged Gigabit switch that offers eight 10/100/1000Base-T copper

ports, including 4 PoE+ capable ports (up to 30 Watts each).

Red Lion’s industrial Power over Ethernet (PoE) solutions are designed to transmit power and data over an
Ethernet network. PoE networks eliminate the need for running separate wires for power and are ideal in
installations with devices such as IP surveillance cameras, wireless access points, IP phones and other PoE­enabled devices. These industrial PoE devices offer a compact, rugged design for harsh, remote locations.

Key Features

• Compact Space Saving Package

• Unmanaged Operation

• Jumbo Frame Support (1005TX and 1008TX only)

• Extended Environmental Specifications

• Supports Full/Half Duplex Operation

• Up to 16.0 Gb/s Maximum Throughput

• MDIX Auto Sensing Cable

• Auto Sensing Speed and Flow Control

• Full Wire Speed Communication

• Store-and-Forward Switching Technology

• Redundant Power Inputs

• LED Link/Activity Status Indication

• Industry Standard 35mm DIN-Rail Mounted Enclosure

• Plug-and Play installation

N-Tron® Series 1000 Hardware Guide 1-1

Revised 2016-08-30 Introduction and Specifications
Drawing Number LP1001

Model 1002MC

The 1002MC provides one RJ-45 auto sensing 10/100/1000BaseT port and one 1000BaseSX/LX SFP port. The
RJ-45 port is full/half duplex capable, using state-of-the-art Ethernet switching technology. The switch auto­negotiates the speed and flow control capabilities of the copper port, and configures itself automatically. Up to 2
Gb/s maximum throughput. The 1000BaseSX/LX fiber optic port utilizes industry standard SFP transceivers with
LC style connectors and is configured for full duplex operation. Both multimode and singlemode fiber models are
available.

Key Specifications

Table 1.

PHYSICAL ELECTRICAL

Height 4.0 in. (10.16 cm) Input Voltage 10-30 VDC (Regulated)

Width 1.0 in. (2.54 cm) Input Current 200mA max. @ 24VDC

Depth w/ typical SFP installed 3.6 in. (9.165 cm) Inrush Current 13 Amp/0.8 ms max. @

Weight 0.7 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN-Rail 35 mm Input Wire Size 12-24 AWG

1002MC - Key Specifications

BTU/hr

(Steady State)

24VDC

16.4

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Ca

Storage Temperature -40°C to 85°C 100BaseT  Ca

Operating Humidity 10% to 95%

(Non Condensing)

Operating Altitude 0 to 10,000 ft. 1000BaseSX Multimode

Ingress Protection IP30 1000BaseLX Singlemode 7-10/125μm

Shock 200g @ 10 ms (bulkhead

mounted)

Vibration 50 g, 10-200 Hz, triaxial (bulk-

head mounted)

CONNECTOR RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX One (1) RJ45 TX Copper Port Top 1 in. (2.5 cm)

1000Base-SX/LX SFP One (1) SFP LC Duplex

Gigabit Fiber Port

1000BaseT  Cat-5e

Front 4 in. (10.1 cm)

t-3

t-5

50-62.5/125μm

1-2 N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

LNK
ACT

SPD
1000

10/100/1000Base-T

RX

TX

ACTLNK

1000Base-SX/LX

1002MC

3.85"

[97.77mm]

1.20"

[30.42mm]

3.85"

[97.71mm]

3.61"

[91.65mm]

1.00"

[25.40mm]

4.37"

[110.97mm]

4.00"

[101.60mm]

4.15"

4.15"

[105.47mm]

Drawing No. LP1001

Table 2.

Gigabit Fiber Transceiver SFP Characteristics

NTSFP-SX NTSFP-LX-10 NTSFP-LX-40 NTSFP-LX-80

80km

0dBm

-24dBm

1550nm

DFB

Fiber Length*

TX Power Min

RX Sensitivity Max

Wavelength

Laser Type

550m with 50/125µm

10km 40km

275m @ 62.5/125μm

-9.5dBm -9.5dBm -2dBm

-17dBm -20dBm -22dBm

850nm 1310nm 1310nm

VCSEL FP DFB

*Fiber length distances represent technical performance. Link budgets should be evaluated based on specific application
conditions.

Dimensions

[105.41mm]

1-3

N-Tron® Series 1000 Hardware Guide 1-3

Revised 2016-08-30 Introduction and Specifications

compliant

Drawing Number LP1001

Product Ordering Guide

Part Number Application

1002MC-SX 1000BaseSX Multimode fiber Media Converter
1002MC-LX-ZZ 1000BaseLX Singlemode fiber Media Converter
1000-PM Panel Mount kit, used with 10
NTPS-24-1.3 DIN-Rail Power Supply 24V@1.3 Amp
Where: “ZZ” is: 10 for 10km maximum fiber segment length

40 for 40km maximum fiber segment length
80 for 80km maximum fiber segment length

02MC, 1003GX2, 1005TX, 1008TX

Model 1002MC Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment.

• ANSI/ISA-12.12.01-2007 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Group

s A, B, C, D. T4A.

• cUL C22.2 No. 14-M05

• cUL C22.2 No. 213-M1987 for use in Class I, Division 2 Hazardous Locations.

EMI

•

EN61000-6-4, EN55011 - Class A

• FCC Title 47, Part 15, Subpart B - Class A

• ICES-003 – Class A

EMC

•

EN61000-6-2

• EN61000-4-2 (ESD)

• EN61000-4-3 (RS)

• EN61000-4-4 (EFT)

• EN61000-4-5 (Surge)

• EN61000-4-6 (Conducted Disturbances)

Warranty

3 years from the date of purchase.

1-4 N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

Drawing No. LP1001

Model 1003GX2

The 1003GX2 offers one auto sensing 10/100/1000Base-T copper port and two 1000BaseT/SX/LX full duplex
copper/fiber ports. The RJ-45 port is full/half duplex capable, using state-of-the-art Ethernet switching technology.
The switch auto-negotiates the speed and flow control capabilities of the copper port, and configures itself
automatically. Up to 6 Gb/s Maximum Throughput. The 1000BaseSX/LX fiber optic port utilizes industry standard
SFP transceivers with LC style connectors and is configured for full duplex operation. The 1003GX2 offers models
in a combination of Singlemode and Mix-and-Match Multimode configurations.

• The 1003GX2-B has one 10/100/1000BaseT port and two (2) 1000BaseSX/LX SFP ports that support a

combination of Multimode and Singlemode Mini-GBIC SFP transceivers (SFP transceivers sold separately)

• The 1003GX2-SX has one 10/100/1000BaseT port and two (2) 1000BaseSX SFP fiber transceivers.

• The 1003GX2-LX-10 has one 10/100/1000BaseT port and two (2) 1000BaseLX-10 SFP transceivers

• The 1003GX2-LX-40 has one 10/100/1000BaseT port and two (2) 1000BaseLX-40 SFP transceivers

• The 1003GX2-LX-80 has one 10/100/1000BaseT port and two (2) 1000BaseLX-80 SFP transceivers.

Key Specifications

Table 3. 1003GX2 Key Specifications

PHYSICAL ELECTRICAL

Height 4.0 in. (10.16 cm) Input Voltage 10-30 VDC (Regulated)

Width 1.0 in. (2.54 cm) Input Current 200mA max. @ 24VDC

(Steady State)

Depth 3.6 in. (9.165 cm) Inrush Current 13 Amp/0.8 ms max. @

24VDC

Weight 0.7 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN-Rail 35 mm Input Wire Size 12-24 AWG

BTU/hr

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 95%

(Non Condensing)

Operating Altitude 0 to 10,000 ft. 1000BaseSX Multimode

Ingress Protection IP30 1000BaseLX Singlemode 7-10/125μm

Shock 200g @ 10 ms (bulkhead

mounted)

Vibration 50 g, 10-200 Hz, triaxial (bulk-

head mounted)

CONNECTORS RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX One (1) RJ45 TX Copper Port To p 1 in. (2.5 cm)

1000Base-SX/LX SFP Up to two (2) SFP LC Duplex

Gigabit Fiber Ports

1000BaseT  Cat-5e

Front 4 in. (10.1 cm)

16.4

50-62.5/125μm

N-Tron® Series 1000 Hardware Guide 1-5

Revised 2016-08-30 Introduction and Specifications
Drawing Number LP1001

Table 4. Gigabit Fiber Transceiver (SFP) Characteristics

NTSFP-SX NTSFP-LX-10 NTSFP-LX-40 NTSFP-LX-80

Fiber Length 550m with 50/125µm

10km 40km 80km

275m @ 62.5/125μm

TX Power Min -9.5dBm -9.5dBm -2dBm 0dBm

RX Sensitivity Max -17dBm -20dBm -22dBm -24dBm

Wavelength 850nm 1310nm 1310nm 1550nm

Laser Type VCSEL FP DFB DFB

*Fiber length distances represent technical performance. Link budgets should be evaluated based on specific application
conditions.

Dimensions

1-6 N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

compliant

Drawing No. LP1001

Product Ordering Guide

Part Number Application

1003GX2-B One 10/100/1000BaseT port; Two (2)1000BaseSX/LX SFP po

Multimode and Singlemode SFP Mini-GBIC fiber transceivers. Note: Unit must be populated
with two SFP transceivers upon shipment

1003GX2-SX One 10/100/1000BaseT port; Two (2) 1000BaseSX SFP fiber transceivers

1003GX2-LX-10 One 10/100/1000BaseT port; Two (2) 1000BaseLX-10 SFP fiber transceivers

1003GX2-LX-40 One 10/100/1000BaseT port; Two (2) 1000BaseLX-40 SFP fiber transceivers

1003GX2-LX-80 One 10/100/1000BaseT port; Two (2) 1000BaseLX-80 SFP fiber transceivers

1000-PM Panel Mount Kit, used with 1002MC, 1003GX2, 1005TX,1008TX

NTPS-24-1.3 DIN-Rail Power Supply 24V@1.3Amp

NTSFP-SX One 1000BaseSX Multimode SFP Gigabit Transceiver (two required per unit)

NTSFP-LX-ZZ* One 1000BaseSX Singlemode SFP Gigabit Transceiver (two required per unit) Note: Unit

mu

st be populated with two SFP transceivers upon shipment

* ZZ = 10, 40, or 80 for GB Singlemode SFP Transceiver

rts supporting a combination of

Model 1003GX2 Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment.

• ANSI/ISA-12.12.01-2007 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Group

s A, B, C, D. T4A.

• cUL C22.2 No. 14-M05

• cUL C22.2 No. 213-M1987 for use in Class I, Division 2 Hazardous Locations.

EMI

EN61000-6-4, EN55011 - Class A

•

• FCC Title 47, Part 15, Subpart B - Class A

• ICES-003 – Class A

EMC

•

EN61000-6-2

• EN61000-4-2 (ESD)

• EN61000-4-3 (RS)

• EN61000-4-4 (EFT)

• EN61000-4-5 (Surge)

• EN61000-4-6 (Conducted Disturbances)

Warranty

3 years from the date of purchase.

N-Tron® Series 1000 Hardware Guide 1-7

Revised 2016-08-30 Introduction and Specifications
Drawing Number LP1001

Model 1005TX

The 1005TX is a five port unmanaged Gigabit switch that offers five 10/100/1000Base-T RJ-45 ports. The RJ-45
port is full/half duplex capable, using state-of-the-art Ethernet switching technology. The switch auto-negotiates
the speed and flow control capabilities of the copper port, and configures itself automatically. Up to 10 Gb/s
maximum throughput. It is designed for use in mission critical data acquisition, control, and Ethernet I/O
applications where Gigabit capability is required. The 1005TX Gigabit network switch is designed to solve the most
demanding industrial communication requirements while providing high throughput and minimum downtime.

Key Specifications

Table 5.

PHYSICAL ELECTRICAL

Height 4.0 in. (10.16 cm) Input Voltage 10-30 VDC (Regulated)

Width 1.0 in. (2.54 cm) Input Current 230mA max. @ 24VDC

Depth 3.6 in. (9.165 cm) Inrush Current 13 Amp/0.6 ms max. @

Weight 0.7 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN-Rail 35 mm Input Wire Size 12-24 AWG

1005TX Key Specifications

BTU/hr

(Steady State)

24VDC

18.8

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 95%

(Non Condensing)

Operating Altitude 0 to 10,000 ft.

Ingress Protection IP30

Shock 200g @ 10 ms (bulkhead

mounted)

Vibration 50 g, 10-200 Hz, triaxial (bulk-

head mounted)

CONNECTORS RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX Five (5) RJ45 TX Copper

Po

rts

1000BaseT  Cat-5e

To p 1 in. (2.5 cm)

Front 2 in. (5.0 cm)

1-8 N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

Drawing No. LP1001

Dimensions

Product Ordering Guide

Part Number Application

1005TX Five port 10/100/1000BaseT Ethernet switch

1000-PM Panel Mount kit

NTPS-24-1.3 DIN-Rail Power Supply 24V@1.3 Amp

N-Tron® Series 1000 Hardware Guide 1-9

Revised 2016-08-30 Introduction and Specifications

compliant

Drawing Number LP1001

Model 1005TX Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment

• ANSI/ISA-12.12.01-2015 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Groups A, B, C, D. T4

• cUL C22.2 No. 14-13 Industrial Control Equipment

• cUL C22.2 No. 213-15 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous (Classified)

Locations.

EMI

• EN61000-6-4, EN55011 - Class A

• FCC Title 47, Part 15, Subpart B - Class A

• ICES-003 – Class A

EMC

• EN61000-6-2

• EN61000-4-2 (ESD)

• EN61000-4-3 (RS)

• EN61000-4-4 (EFT)

• EN61000-4-5 (Surge)

• EN61000-4-6 (Conducted Disturbances)

Warranty

3 years from the date of purchase.

1-10 N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

Drawing No. LP1001

Model 1008TX

The 1008TX is an unmanaged Gigabit switch that offers eight Gigabit 10/100/1000Base-T RJ-45 ports. The RJ-45
port is full/half duplex capable, using state-of-the-art Ethernet switching technology. The switch auto-negotiates
the speed and flow control capabilities of the copper port, and configures itself automatically. Up to 16 Gb/s
maximum throughput. It has redundant power inputs.

Key Specifications

Table 6.

PHYSICAL ELECTRICAL

Height 4.6 in. (11.76 cm) Input Voltage 10-49 VDC (Regulated)

Width 1.5 in. (3.94 cm) Input Current 250mA max. @ 24VDC

Depth 4.0 in. (10.37 cm) Inrush Current 20 Amp/0.06 ms max. @

Weight 0.7 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN-Rail 35 mm Input Wire Size 12-24 AWG

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 95%

(

Non Co nden sing)

Operating Altitude 0 to 10,000 ft.

Ingress Protection IP20

Shock 200g @ 10 ms (bulkhead

mounted)

Vibration 50 g, 10-200 Hz, triaxial (bulk-

head mounted)

1008TX Key Specifications

BTU/hr

1000BaseT  Cat-5e

(Steady State)

24VDC

20.5

CONNECTORS RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX Eight (8) RJ45 TX Copper

Ports

To p 1 in. (2.5 cm)

Front 2 in. (5.0 cm)

N-Tron® Series 1000 Hardware Guide 1-11

Revised 2016-08-30 Introduction and Specifications
Drawing Number LP1001

Dimensions

1-12 N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

compliant

Drawing No. LP1001

Product Ordering Guide

Part Number Application

1008TX Eight port 10/100/1000BaseT Ethernet switch

1000-PM Panel Mount kit

NTPS-24-1.3 DIN-Rail Power Supply 24V@1.3 Amp

Model 1008TX Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment.

• ANSI/ISA-12.12.01-2015 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Groups A, B, C, D. T4.

• cUL C22.2 No. 14-13 Industrial Control equipment

• cUL C22.2 No. 213-15 for use in Class I, Division 2 and Class III Divisions 1 and 2 Hazardous (Classified)

Locations.

EMI

FCC Title 47, Part 15, Subpart B - Class A

•

• Industry Canada ICES-003 – Class A

• EN 55011 - Class A

• EN 61000-6-4

• EN 61000-3-2/3

EMC

EN 61000-6-2

•

• EN 61000-4-2/3/4/5/6/8/11

Warranty

3 years from the date of purchase.

N-Tron® Series 1000 Hardware Guide 1-13

Revised 2016-08-30 Introduction and Specifications
Drawing Number LP1001

Model 1008TX-POE+

Red Lion’s N-Tron® series 1008TX-POE+ unmanaged gigabit PoE+ Ethernet switch features plug-and-play
operation for up to eight 10/100/1000Base-T(X) devices with Power Over Ethernet Plus (PoE+) support on four
ports. The 1008TX-POE+ will output up to 30 Watts of power along with data on each of its four IEEE 802.3af/at
compliant PoE+ ports to PoE/PoE+ compliant powered devices (PDs), eliminating the need to run separate power
lines. Built-in power boost technology dynamically boosts power from either of the 22-49 VDC power inputs to meet
PoE+ requirements.

Key Specifications

Table 7. 1008TX-POE+ Key Specifications

PHYSICAL ELECTRICAL

Height 5.9 in. (14.99 cm) Input Voltage 22-49 VDC (Regulated)

Width 2.0 in. (5.11 cm) Input Current 5.6A max. @ 24VDC

(Under Full Load)

Depth 5.9 in. (15.04 cm) Inrush Current 70.5 Amp/60us @ 24VDC

Weight 1.5 lbs (0.69 kg) Input Ripple Less than 100 mV

DIN-Rail 35 mm Input Wire Size 12-16 AWG

BTU/hr 60

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 80°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 95%

(Non Condensing)

Operating Altitude 0 to 10,000 ft. 802.3af (802.3at Type 1) PoE

Ingress Protection IP20 802.3at Type 2 PoE+  Cat-5

Shock 200g @ 10 ms

(bulkhead mounted)

Vibration 50 g, 10-200 Hz, triaxial

(bulkhead mounted)

CONNECTORS RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000Base-T four (4) RJ45 

Ports

10/100/1000Base-T/PoE+ four (4) RJ45 TX/PoE+

Ports

POWER OVER ETHERNET

PoE Standard
IEEE 802.3af/at Gigabit Mid-Span PSE

PoE Output Power
57VDC/30W (25.5W at PD) per port

Power Pin assignment
Pins 1/2 (+) Pins 3/6 (-)

PSE Type
Type 2

1000BaseT  Cat-5e

 Cat-3

To p 1 in. (2.5 cm)

Front

2 in. (5.0 cm)

1-14 N-Tron® Series 1000 Hardware Guide

Introduction and Specifications Revised 2016-08-30

Drawing No. LP1001

Dimensions

N-Tron® Series 1000 Hardware Guide 1-15

Revised 2016-08-30 Introduction and Specifications

compliant

Drawing Number LP1001

Product Ordering Guide

Part Number Application

1008TX-POE+ Eight port Industrial Unmanaged Gigabit PoE+ Switch (4 10/100/1000Base-T ports, 4 10/100/

1000Base-T with PoE+ ports)

1K26-PMK Panel Mount kit, 1000 Series

NTPS-24-10 DIN-Rail Power Supply, 24V@10 Amp

Model 1008TX-POE+ Regulatory Approvals

Safety

•

ANSI/ISA 12.12.01-2015 Class I and II, Div. 2 and Class III, Div. 1 and 2, Groups A, B, C and D Hazardous
Locations, T4

• UL508 Industrial Control Equipment

• CAN/CSA-C22.2 No. 213-15, Hazardous Locations

• CAN/CSA-C22.2 No. 14-13, Industrial Control Equipment

EMI

•

FCC Title 47, Part 15, Radio Frequency Devices, Subpart B, ANSI C63.4-2009;

• Industry Canada ICES-003, EN 55032, EN 61000-3-2, EN61000-3-3

EMC

•

EN 55024, EN 61000-6-2, EN 61000-4-2 (ESD); EN 61000-4-3 (RFAM); EN 61000-4-4 (EFT); EN 61000-4-5
(SURGE); EN 61000-4-6 (RFCM); EN 61000-4-8 (PFMF); EN 61000-4-11 (VDI)

Warranty

3 years from the date of purchase.

1-16 N-Tron® Series 1000 Hardware Guide

Installation Revised 2016-08-30

Drawing No. LP1001

Section 2 Installation

Introduction

This sections contains the information and procedures necessary to unpack, inspect, install and connect the
N-Tron® Series 1000 equipment.

Unpacking

Remove all the equipment from the packaging, and store the packaging in a safe place.

Inspection

Please ensure the shipping package contains the following items in undamaged condition:

1. N-Tron® Series 1000 Media Converter or Ethernet Switch.

2. Product CD.

If the package contents are damaged:

1. Contact your carrier.

2. File any damage claims with the carrier.

Installing/Mounting

Read the following warning before beginning the installation:

Lire l'avertissement suivant avant de commencer l'installation:

WARNING: Never install or work on electrical equipment or cabling during periods of lightning
activity. Never connect or disconnect power when hazardous gases are present.
ALERTE: Ne jamais installer ou de travailler sur un équipement électrique ou de câblage pendant
les périodes d'activité de la foudre. Ne jamais brancher ou débrancher l'alimentation en gaz
dangereux sont présents

N-Tron® Series 1000 Hardware Guide 2-17

Revised 2016-08-30 Installation
Drawing Number LP1001

DIN-Rail Mounting

a. Install the unit in a standard DIN-Rail. Recess the unit to allow at least 2” of horizontal clearance for

CAT5e cable bend radius or 5” of horizontal clearance for Fiber Optic cable bend radius.

b. To install the unit to 35mm industrial DIN-Rail,

place the top edge of the included mounting bracket
on the back of the unit against the DIN-Rail at a 15°
angle as shown. Rotate the bottom of the unit to the
back (away from you) until it snaps into place.

c. To remove the unit from the 35mm industrial

DIN-Rail, pull forward on the unit until it
disengages from the bottom of the DIN-Rail.
Rotate the bottom of the unit towards you and up
at an approximate 15° upward angle to
completely remove the unit.

UR MK 10 00 -P M 1K 26 -P MK

Most Red Lion N-Tron™ products are designed to be mounted on industry standard 35mm DIN-Rail. However,
DIN-Rail mounting may not be suitable for all applications. Our Universal Rack Mount Kit (P/N: URMK) can be
used to mount the 1000 Series enclosures to standard 19" racks, and our Panel Mount Assembly (P/N: 1000-PM)
can be used to mount the 1000 Series enclosures to a panel or any other flat surface.The 1008TX-POE+ will
require the 1K26-PMK panel mount.

2-18 N-Tron® Series 1000 Hardware Guide

Installation Revised 2016-08-30

Drawing No. LP1001

Connections

Power Connection (Top View)

1. Unscrew & Remove the DC Voltage Input Plug from the top header.

2. Install the DC Power Cables into the Plug (observing polarity on unit).

3. Plug the Voltage Input Plug back into the top header.

4. Tightening torque for the terminal block power plug is 0.5 Nm/0.368 Pound Foot.

5. Verify the Power LED stays ON (GREEN).

Note: Either V1 or V2 can be connected to power for minimal operation. For redundant power

operation, V
24 gauge for non-PoE models and 12-16 gauge for PoE models . Limit the power cord length to less

than 10 meters in order to ensure optimum performance.

Recommend using 24V DC Power Supplies, similar to:

and V2 plugs must be connected to separate DC Voltage sources. Use wire sizes of 12-

1

•100-240VAC: N-Tron NTPS-24-1.3, DC 24V/1.3A

•100-240VAC: N-Tron NTPS-48-5, DC 48/5A Ground Connection

•100-240VAC: N-Tron NTPS-24-10, DC 24V/10A

Ground Connection

N-Tron Series Switch Grounding Techniques for 1000 Series

The grounding of any control system is an integral part of the design. Optimum noise immunity and emissions are
obtained when the chassis is connected to earth ground via a 12-14 gauge drain wire. The N-Tron series models
provide a ground lug that is used to provide a safe grounding path of the device.

N-Tron® Series 1000 Hardware Guide 2-19

Revised 2016-08-30 Installation
Drawing Number LP1001

Users may run a drain wire & lug from the screw provided on the back face of the
enclosure. In the event the provided grounding screw has been lost, care should
be taken to limit the penetration of the outer skin by less than 1/4 in. Failure to do
so may cause irreversible damage to the internal components of the switch.

Note: Ensure the power supply is grounded properly before
applying power to the grounded switch. This can be verified by
using a voltmeter to determine that there is no voltage difference
between the power supply’s negative output terminal and the
chassis grounding point of the switch.

Drain wire with lug connecting switch chassis
to known grounding posts.

Note: The V-legs of the power input connector are connected to the chassis internally on the
1002MC, 1003GX2 and 1005TX. Before applying power to the grounded switch, you must use a
volt meter to verify there is no voltage difference between the power supply’s negative output
terminal and the switch chassis grounding point.

Note: The 1008TX and 1008TX-POE+ power input (V-) pins are isolated from chassis ground. Do
not attempt to ground the switch to earth ground via the power input pins (V-).

If the use of shielded cables is required, it is generally recommended to only connect the shield at one end to
prevent ground loops and interfere with low level signals (i.e. thermocouples, RTD, etc.). Cat5e cables
manufactured to EIA-568A or 568B specifications are required for use with N-Tron series switches.



In the event all Cat5e patch cable distances are small (i.e. All Ethernet devices are located the same local cabinet
and/or referenced to the same earth ground), it is permissible to use fully shielded cables terminated to chassis
ground at both ends in systems void of low level analog signals.

2-20 N-Tron® Series 1000 Hardware Guide

Installation Revised 2016-08-30

Drawing No. LP1001

RJ45 Connector Crimp Specifications

Please reference the illustration below for your Cat5 cable specifications:

Cable Connection

Cable connections are dependent on the network configuration and N-Tron® Series 1000 model in use.

1. Fo

r 10Base-T ports, plug a Category 3 (or greater) twisted pair cable into the RJ45 connector.

2. F

or 100/1000Base-T ports, plug a Category 5e (or greater) twisted pair cable into the RJ45 connector.

Connect the other end to the far end station. The total length should not exceed 100 meters.

erify that the LNK/ACT LEDs are ON once the connection has been completed.

3. V

4. T

o connect any other port to another Switch or Repeater, use a standard Cat5e straight through or crossover

cable.

CAUTION: Creating a port to port connection on the same switch (i.e. loop) is an illegal
operation and will create a broadcast storm which will crash the network!

ATTENTION: Création d'un port de connexion du port sur l e même commutateur
(c.-à-boucle) est une opération illégale et va créer une tempête de diffusion qui va planter
le réseau!

N-Tron® Series 1000 Hardware Guide 2-21

Revised 2016--08-30 Operation and Maintenance
Drawing No. LP1001

Section 3 Operation and Maintenance

Introduction

The N-Tron® Series 1000 Gigabit Media Converter & Industrial Gigabit Ethernet Switch devices provide operating
status information through the LED indicators located on the front panel.

Controls and Indicators

Model 1002MC, 1003GX2, 1005TX Indicators

Table 8.

INDICATOR DESCRIPTION

LNK/ACT

SPD1000

3-22 N-Tron® Series 1000 Hardware Guide

Model 1002MC, 1003GX2, 1005TX Indicators (from top to bottom)

Green LED lights when power is connected

LED indicating link/activity

LED indicating 1000 Link data speed

Operation and Maintenance Revised 2016--08-30

Drawing No. LP1001

INDICATOR STATE DESCRIPTION

LNK/ACT

SPD1000

Model 1008TX Indicators

Table 9.

Model 1002MC, 1003GX2, 1005TX Indicator States

ON Power is applied

OFF Power is off

BLINKING Link established, activity on cable

OFF No link activity on cable

ON Link is operating at 1000Mbps

OFF Link is operating at 10/100Mbps

Table 10. Model 1008TX Indicators (from top to bottom)

INDICATOR DESCRIPTION

ACT

1000

Green LED lights when power is connected

LED indicating activity

LED indicating 1000 Link data speed

Table 11 describes the indicator states and the operating modes:

N-Tron® Series 1000 Hardware Guide 3-23

Revised 2016--08-30 Operation and Maintenance
Drawing No. LP1001

Table 11 . Model 1008TX Indicator States

INDICATOR STATE DESCRIPTION

ON Power is applied

OFF Power is off

ACT

ON/BLINKING Link established, activity on cable

OFF No link activity on cable

1000

ON Link is operating at 1000Mbps

OFF Link is operating at 10/100Mbps

Model 1008TX-POE+ Indicators

Table 12.

INDICATOR DESCRIPTION

V1

V2

PoE Port Status

ACT

1000

Model 1008TX-POE+ Indicators (from top to bottom)

V1 Power LED

V2 Power LED

Power Supply

PoE activity

LED indicating activity

LED indicating 1000 Link data speed

Table 13 describes the indicator states and the operating modes:

3-24 N-Tron® Series 1000 Hardware Guide

Operation and Maintenance Revised 2016--08-30

Drawing No. LP1001

Table 13.

INDICATOR COLOR/STATE DESCRIPTION

Model 1008TX-POE+ Indicator States

GREEN Valid Power (22-49VDC) is applied on corresponding voltage input.

RED Invalid Power (<20VDC) is applied to corresponding voltage input.

ACT

OFF No power is applied to

ON/BLINKING Link established, activity on cable.

the device.

OFF No link activity on cable.

1000

ON Link established, activity on cable.

OFF No link activity on cable.

PoE Port Status

GREEN PoE power is being applied to the corresponding port.

OFF No PoE power is being applied to the corresponding port.

Maintenance

Maintenance is limited to verifying the cable interface and unit cleaning.

Verify/Troubleshoot Cable Interface

1. Make sure the (Power LED) is ON.

2. M

ake sure you are supplying sufficient current for the chosen switch version.



Note: The

inrush current will exceed the steady state current by ~ 2X.

erify that Link LEDs are ON for both ports.

3. V

4. V

erify cabling used between stations.

5. V

erify that cabling is Category 3 or greater for 10Mbps Operation.

Cleaning

Clean hardware only with a damp cloth.

N-Tron® Series 1000 Hardware Guide 3-25

Revised 2016--08-30 Operation and Maintenance
Drawing No. LP1001

LIMITED WARRANTY

(a) Red Lion Controls Inc., Sixnet Inc., N-Tron Corporation, or Blue Tree Wireless Data, Inc. (the “Company”) war­rants that all Products shall be free from defects in material and workmanship under normal use for the period of
time provided in “Statement of Warranty Periods” (available at

www.redlion.net) current at the time of shipment of

the Products (the “Warranty Period”). EXCEPT FOR THE ABOVE-STATED WARRANTY, COMPANY MAKES NO

WARRANTY WHATSOEVER WITH RESPECT TO THE PRODUCTS, INCLUDING ANY (A) WARRANTY OF
MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE; OR (C) WARRANTY
AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY; WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE
OR OTHERWISE. Customer shall be responsible for determining that a Product is suitable for Customer’s use and

that such use complies with any applicable local, state or federal law.

(b) The Company shall not be liable for a breach of the warranty set forth in paragraph (a) if (i) the defect is a result
of Customer’s failure to store, install, commission or maintain the Product according to specifications; (ii) Customer
alters or repairs such Product without the prior written consent of Company.

(c) Subject to paragraph (b), with respect to any such Product during the Warranty Period, Company shall, in its
sole discretion, either (i) repair or replace the Product; or (ii) credit or refund the price of Product provided that, if
Company so requests, Customer shall, at Company's expense, return such Product to Company.

(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL BE THE CUSTOMER'S SOLE AND EXCLUSIVE

REMEDY AND COMPANY'S ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET
FORTH IN PARAGRAPH (a).

3-26 N-Tron® Series 1000 Hardware Guide