red lion N-Tron 1000 Series, N-Tron 1005TX, N-Tron 1002MC, N-Tron 1003GX2, N-Tron 1008TX Hardware Manual

N-Tron® 1000 Series

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Industrial Gigabit Media Converters
& Gigabit Ethernet Switches

Hardware Guide | March 2015

COPYRIGHT

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Copyright, © 2015 Red Lion Controls, Inc.
20 Willow Springs Circle
York, PA 17406
All rights reserved. Red Lion, the Red Lion logo and N-Tron are registered trademarks of Red Lion Controls,

Inc. All other company and product names are trademarks of their respective owners.
The information contained in this document is subject to change without notice. Red Lion makes no warranty

of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability
or fitness for a particular purpose. In no event shall Red Lion be liable for any incidental, special, indirect or
consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions
in this manual or the information contained herein.

CONTACT INFORMATION :

AMERICAS

York, PA: [phone]
Mobile, AL: [phone]
Ballston Lake, NY: [phone]
Hours: 8am-6pm Eastern Standard Time
(UTC/GMT -5 hours)

ASIA-PACIFIC

Shanghai, P.R. China: [phone] x767
Hours: 10am-6pm China Standard Time
(UTC/GMT +8 hours)

EUROPE

The Netherlands: [phone]
Hours: 9am-6pm Central European Time
(UTC/GMT +1 hour)

Table of Contents Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Table of Contents

Preface

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Part 15 of the Federal Communications Commission (FCC) - A Rules: Interference . . . . . . iii

Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Environmental Impact Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Toxic Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Trademark Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Release Notes and Document Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Publication History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Document Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Additional Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

General Safety Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Electrical Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Environmental Safety Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Hazardous Location Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Laser Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Introduction and Specifications

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Product Ordering Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Model 1002MC Key Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Model 1002MC Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

EMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

EMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Model 1003GX2 - Key Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Model 1003GX2 Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

EMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

EMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

N-Tron 1000 Series Hardware Guide i

Table of Contents Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Model 1005TX - Key Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Model 1005TX Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

EMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

EMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Model 1008TX - Key Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Model 1008TX Regulatory Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

EMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

EMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Installation

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Installing/Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

DIN-Rail Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Power Connection (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

N-Tron Series Switch Grounding Techniques for 1000 Series . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Operation and Maintenance

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Model 1002MC, 1003GX2, 1005TX Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Model 1008TX Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Verify/Troubleshoot Cable Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Red Lion Controls N-Tron 1000 Series Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

ii N-Tron 1000 Series Hardware Guide

Preface Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Preface

Disclaimer

Portions of this document are intended solely as an outline of methodologies to be followed during the
maintenance and operation of N-Tron 1000 Series equipment. It is not intended as a step-by-step guide or a
complete set of all procedures necessary and sufficient to complete all operations.

While every effort has been made to ensure that this document is complete and accurate at the time of release, the
information that it contains is subject to change. Red Lion Controls is not responsible for any additions to or
alterations of the original document. Industrial networks vary widely in their configurations, topologies, and traffic
conditions. This document is intended as a general guide only. It has not been tested for all possible applications,
and it may not be complete or accurate for some situations.

Users of this document are urged to heed warnings and cautions summarized at the front of the document, such as
electrical hazard warnings.

Compliance Information

It is recommended that the owner of this equipment determine and ensure conformance with any specific and
applicable local regulations.

Part 15 of the Federal Communications Commission (FCC) - A Rules: Interference

Every effort has been made to ensure that this equipment is designed to comply with the limits for a Class A digital
device, as described in the FCC Rules.

This product complies with Part 15 of the FCC-A Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful Interference

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Operation of this device in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulations. Operation is subject to the following two conditions; (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.

Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des
règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas
causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris
l'interférence qui peut causer l'opération peu désirée.

N-Tron 1000 Series Hardware Guide iii

Preface Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Environmental Impact Statement

Red Lion equipment contains no hazardous materials as defined by the United States Environmental Protection
Agency (USEPA). Red Lion recommends that all failed product be returned to Red Lion for failure analysis and
proper disposal.

Toxic Emissions

Red Lion equipment releases no toxic emissions.

Trademark Acknowledgments

Ethernet is a registered trademark of Xerox Corporation.

EtherNet/IPTM and CIPTM are registered trademarks of ODVA.

Release Notes and Document Updates

The hard copy and electronic media versions of this document are revised only at major releases and therefore,
may not always contain the latest product information. As needed, Documentation Notes and or Product Bulletins
will be provided between major releases to describe any new information or document changes.

The latest online version of this document and all product updates can be accessed through the Red Lion web
site.

Publication History

The following information lists the release history of this document.

ISSUE/REVISION RELEASE DATE CONTENT DESCRIPTION

Revised 2014-01-23 January 2014 Document Updates

Revised 2015-03-17 March 2015 Added 1008TX Model, Format Changes

Revised 2015-03-24 March 2015 Format Changes to Cover, Page Header and Tables

Related Documents

Visit the Technical Resources page on the Red Lion website at the following link to view available documents
related to this product.

Document Comments

Red Lion appreciates all comments that will help us to improve our documentation quality. The user can
submit comments through the Red Lion Customer Service. Simply email us.

Additional Product Information

Additional product information can be obtained by contacting the local sales representative or Red Lion through the
contact numbers and/or e-mail addresses listed on the inside of the front cover.

iv N-Tron 1000 Series Hardware Guide

Preface Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Warnings and Cautions

Warnings apply to situations where personal injury or death may result.

Cautions apply to where reduced function or damage to equipment may result.

General Safety Cautions and Warnings

CAUTION: If the N-Tron series equipment is used in the manner not specified by Red Lion, the
protection provided by the equipment may be impaired.

ATTENTION: Si l' N-Tron série équipement est utilisé d'une manière non spécifiée par Red Lion,
la protection fournie par l'équipement peut être compromise.

CAUTION: Do not perform any services on the unit unless qualified to do so. Do not substitute
unauthorized parts or make unauthorized modifications to the unit.

ATTENTION: Ne pas effectuer de services sur l'appareil s'il n'est pas qualifié pour le faire. Ne pas
substituer pièces non autorisées ou de modifications non autorisées de l'appareil.

CAUTION: Do not operate the equipment in a manner not specified by this manual.

ATTENTION: Ne pas faire fonctionner l'équipement d'une manière non spécifiée par ce manuel.

WARNING: Install only in accordance with Local and National Codes of authorities having

jurisdiction.

ALERTE: Installer uniquement, conformément aux codes locaux et nationaux des autorités ayant
compétence.

Electrical Safety Warnings

WARNING: Do not work on equipment or cables during periods of lightning activity.

ALERTE: Ne pas travailler sur le matériel ou les câbles pendant les périodes d'activité de la

foudre.

N-Tron 1000 Series Hardware Guide v

Preface Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

WARNING: Properly ground the unit before connecting anything else to the unit. Units not
properly grounded may result in a safety risk and could be hazardous and may void the warranty.
See the grounding technique section of this Hardware Guide for proper ways to ground the unit.

ALERTE: Correctement à la terre de l'unité avant tout raccordement à l'unité. Unités pas
correctement mise à la terre peut entraîner un risque de sécurité et pourraient être dangereux et
peut annuler la garantie. Voir la section technique de mise à la terre de ce mode d'emploi des
moyens appropriés à la masse de l'appareil.

WARNING: This equipment must be used with a Listed UL Industrial Power Supply.

ALERTE: Cet équipement doit être utilisé avec une alimentation UL Listed industrielle.

WARNING: This equipment (1005TX and 1008TX) must be used with a Listed UL Class 2 Power

Supply.

ALERTE: Cet équipement (1005TX and 1008TX) doit être utilisé avec une alimentation UL Listed
Classe 2.

WARNING: A Recognized or Listed fuse, rated maximum 3A, minimum 30VDC, must be installed
on the line side of the device.

ALERTE: Un fusible reconnu ou classé, classé 3A maximale, 30VDC minimum, doit être installé
sur le côté de la ligne de l'appareil.

WARNING: Use 110°C or higher rated copper wire, (0.22Nm) 2 lb/in tightening torque for field
installed conductors.

ALERTE: Utilisez 110°C ou nominale supérieure fil de cuivre, (0,22 Nm) 2 lb/pouce couple de
serrage pour le champ installé conducteurs.

WARNING: Do not operate the unit with the end plates removed, as this could create a shock or
fire hazard.

ALERTE : Ne pas faire fonctionner l'unité avec les plaques d'extrémité retiré, ce qui pourrait créer
une décharge électrique ou un incendie.

CAUTION: Observe proper DC Voltage polarity when installing power input cables. Reversing
voltage polarity can cause permanent damage to the unit and voids the warranty.

ATTENTION: Respecter la polarité correcte de tension DC lors de l'installation des câbles
d'alimentation d'entrée. Inversion de polarité de tension peut causer des dommages permanents à
l'appareil et annule la garantie.

vi N-Tron 1000 Series Hardware Guide

Preface Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Environmental Safety Cautions and Warnings

CAUTION: This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or
non-hazardous locations only.

ATTENTION: Cet équipement est adapté pour une utilisation dans la classe I, Division 2, Groupes
A, B, C et D ou non dangereux endroits seulement.

WARNING: Explosion Hazard – Substitution of components may impair suitability for Class I,
Division 2.

ALERTE - Risque d'explosion - Remplacement d'un composant peut empêcher la conformité de
Classe I, Division 2.

WARNING: Do not operate the equipment in the presence of flammable gases or fumes. Operat­ing electrical equipment in such an environment constitutes a definite safety hazard.

ALERTE : Ne pas utiliser le matériel en présence de gaz ou de vapeurs inflammables. L'utilisation
de matériel électrique dans un tel environnement constitue un danger certain.

WARNING – Explosion Hazard – Do not connect or disconnect any connections while circuit is
live unless area is known to be non-hazardous.

ALERTE - Risque d'explosion - Ne pas brancher ou débrancher les connexions lorsque le circuit
est sous tension sauf si la zone est connue pour être non dangereux.

WARNING: Disconnect the power and allow to cool 5 minutes before touching.

ALERTE: Déconnectez le câble d'alimentation et laisser refroidir 5 minutes avant de la toucher.

Hazardous Location Warning

WARNING (1005TX and 1008TX only): This equipment is open-type device and is meant to be
installed in an enclosure suitable for the environment that is only accessible with the use of a tool.

ALERTE (1005TX and 1008TX uniquement): Cet équipement est ouvert de type périphérique et
est destiné à être installé dans un boîtier adapté à l'environnement qui n'est accessible qu'avec
l'utilisation d'un outil.

N-Tron 1000 Series Hardware Guide vii

Preface Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Laser Safety Warning

CAUTION (1002MC and 1003GX2 only): CLASS 1 LASER PRODUCT. Do not stare into the
laser.

ATTENTION (1002MC et 1003GX2 uniquement): PRODUIT LASER CLASSE 1. Ne pas regarder
dans le laser.

viii N-Tron 1000 Series Hardware Guide

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Section 1 Introduction and Specifications

Introduction

The N-Tron 1000 Series Unmanaged Industrial Gigabit Ethernet Switches support high speed layer 2 switching
between ports. This series of switches are housed in a ruggedized aluminum enclosure, and provide Category-5
compliant 10/100/1000Base-T connections for high performance network design, and hub/repeater upgrades.

All fiber products utilize the IEEE compliant LC duplex connectors for fiber optic communications in a convenient
SFP (Small Form Pluggable) modular design. All 10/100/1000Base-T ports utilize the RJ45 shielded connectors.

The 1002MC/MCE is a two port unmanaged media converter that converts 10/100/1000Base-T copper to
1000BaseSX/LX full duplex fiber.

The 1003GX2/GXE2 is a three port unmanaged switch that offers one 10/100/1000Base-T copper port and two
1000BaseT/SX/LX full duplex copper/fiber ports.

The 1005TX is a five port unmanaged switch that offers five 10/100/1000Base-T copper ports.

The 1008TX is an eight port unmanaged switch that offers eight 10/100/1000Base-T copper ports.

Key Features

• Compact Space Saving Package

• Full IEEE 802.3 Compliance

• Unmanaged Operation

• Jumbo Frame Support (1005TX and 1008TX only)

• Extended Environmental Specifications

• -40°C to 85°C Operating and Storage Temperature

• Supports Full/Half Duplex Operation

• Up to 16.0 Gb/s Maximum Throughput

• MDIX Auto Sensing Cable

• Auto Sensing Speed and Flow Control

• Full Wire Speed Communication

• Store-and-Forward Switching Technology

• Redundant Power Inputs (10-30 VDC, 10-49VDC for 1008TX)

• LED Link/Activity Status Indication

• Hardened Metal Enclosure

• Industry Standard 35mm DIN Rail Mounted Enclosure

N-Tron 1000 Series Hardware Guide 1-1

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Product Ordering Guide

The 1000 Series Media Converter and Unmanaged Industrial Gigabit Ethernet Switch model part numbers and net­work applications are presented in Table 1.

Table 1. Ordering Guide

PART NUMBER APPLICATION

1002MC-SX 1000BaseSX Multimode fiber Media Converter

1002MC-LX-YY 1000BaseLX Singlemode fiber Media Converter

1003GX2 Three port; One 10/100/100BaseT; Two 1000BaseSX/LX Gigabit Ethernet Switch

1003GX2-B One 10/100/1000BaseT port; Two 1000BaseSX/LX ports with mix-and-match SFP Mini-GBIC

fiber transceivers. Note: Unit must be populated with two SFP transceivers upon shipment

1003GX2-SX One 10/100/1000BaseT port; Two (2) 1000BaseSX SFP Mini-GBIC fiber transceivers

1003GX2-LX-10 One 10/100/1000BaseT port; Two (2) 1000BaseLX-10 SFP transceivers

1003GX2-LX-40 One 10/100/1000BaseT port; Two (2) 1000BaseLX-40 SFP transceivers

1003GX2-LX-80 One 10/100/1000BaseT port; Two (2) 1000BaseLX-80 SFP transceivers

1005TX Five port 10/100/1000BaseT Gigabit Ethernet switch

1008TX Eight port 10/100/1000BaseT Gigabit Ethernet switch

NTSFP-SX One 1000BaseSX Multimode SFP Gigabit Transceiver with LC Style Connector for up to

550m fiber segment length (two required per unit)

NTSFP-LX-ZZ One 1000BaseLX Singlemode SFP Gigabit Transceiver with LC Style Connector for up to ZZ

fiber segment length (two required per unit)

NTPS-24-1.3 DIN-Rail Power Supply 24V@1.3 amp; Used with all models

1000-PM Panel Mount kit; Used with all models

Where: “YY” or “ZZ” is: 10 for 10km maximum fiber segment length

40 for 40km maximum fiber segment length
80 for 80km maximum fiber segment length

N-Tron 1000 Series Hardware Guide 1-2

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Model 1002MC Key Specifications

Table 2. 1002MC - Key Specifications

PHYSICAL ELECTRICAL

Height 4.0” (10.16 cm) Input Voltage 10-30 VDC (Regulated)

Width 1.0” (2.54 cm) Input Current 200mA max. @ 24VDC

(Steady State)

Depth w/ typical SFP installed 3.61” (9.165 cm) Inrush Current 13 Amp/0.8 ms max. @

24VDC

Weight 0.70 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN Rail 35 mm Input Wire Size 12-24 AWG

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 90%

(Non Condensing)

Operating Altitude 0 to 10,000 ft. 1000BaseSX Multimode 50-62.5/125m

1000BaseT  Cat-5e

1000BaseLX Singlemode 7-10/125m

CONNECTOR RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX One (1) RJ45 TX Copper Port Top 1 " (2.54 cm)

1000Base-X SFP One (1) SFP LC Duplex

Gigabit Fiber Port

Front 4 " (10.16 cm)

Table 3. Gigabit Fiber Transceiver SFP Characteristics

NTSFP-SX NTSFP-LX-10 NTSFP-LX-40 NTSFP-LX-80

FIBER LENGTH

TX POWER MIN

RX SENSITIVITY MAX

WAVELENGTH

ASSUMED FIBER LOSS

LASER TYPE

550m with 50/125m

275m @ 62.5/125m

-9.5dBm -9.5dBm -2dBm 0dBm

-17dBm -20dBm -22dBm -24dBm

850nm 1310nm 1310nm 1550nm

3.5 to 3.75 dB/km 0.45 dB/km 0.35 dB/km 0.25 dB/km

VCSEL FP DFB DFB

10km 40km 80km

N-Tron 1000 Series Hardware Guide 1-3

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Model 1002MC Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment.

• ANSI/ISA-12.12.01-2007 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Groups A, B, C, D. T4A.

• cUL C22.2 No. 14-M05

• cUL C22.2 No. 213-M1987 for use in Class I, Division 2 Hazardous Locations.

EMI

EN61000-6-4, EN55011 - Class A

•

• FCC Title 47, Part 15, Subpart B - Class A

• ICES-003 – Class A

EMS

EN61000-6-2

•

• EN61000-4-2 (ESD)

• EN61000-4-3 (RS)

• EN61000-4-4 (EFT)

• EN61000-4-5 (Surge)

• EN61000-4-6 (Conducted Disturbances)

Warranty

3 years from the date of purchase.

N-Tron 1000 Series Hardware Guide 1-4

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Model 1003GX2 - Key Specifications

Table 4. 1003GX2 Key Specifications

PHYSICAL ELECTRICAL

Height 4.0” (10.16 cm) Input Voltage 10-30 VDC (Regulated)

Width 1.0” (2.54 cm) Input Current 200mA max. @ 24VDC

(Steady State)

Depth w/ typical
SFP installed

Weight 0.7 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN Rail 35 mm Input Wire Size 12-24 AWG

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 90%

Operating Altitude 0 to 10,000 ft. 1000BaseSX Multimode 50-62.5/125m

3.61” (9.165 cm) Inrush Current 13 Amp/0.8 ms max. @
24VDC

1000BaseT  Cat-5e

(Non Condensing)

1000BaseLX Singlemode 7-10/125m

CONNECTORS RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX One (1) RJ45 TX Copper Port Top 1 " (2.54 cm)

1000Base-X SFP Up to two (2) SFP LC Duplex

Gigabit Fiber Ports

Front 4 " (10.16 cm)

Table 5. Gigabit Fiber Transceiver (SFP) Characteristics

NTSFP-SX NTSFP-LX-10 NTSFP-LX-40 NTSFP-LX-80

FIBER LENGTH

TX POWER MIN

RX SENSITIVITY MAX

WAVELENGTH

ASSUMED FIBER LOSS

LASER TYPE

550m with 50/125m
275m @ 62.5/125m

-9.5dBm -9.5dBm -2dBm 0dBm

-17dBm -20dBm -22dBm -24dBm

850nm 1310nm 1310nm 1550nm

3.5 to 3.75 dB/km 0.45 dB/km 0.35 dB/km 0.25 dB/km

VCSEL FP DFB DFB

10km 40km 80km

N-Tron 1000 Series Hardware Guide 1-5

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Model 1003GX2 Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment.

• ANSI/ISA-12.12.01-2007 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Groups A, B, C, D. T4A.

• cUL C22.2 No. 14-M05

• cUL C22.2 No. 213-M1987 for use in Class I, Division 2 Hazardous Locations.

EMI

EN61000-6-4, EN55011 - Class A

•

• FCC Title 47, Part 15, Subpart B - Class A

• ICES-003 – Class A

EMS

EN61000-6-2

•

• EN61000-4-2 (ESD)

• EN61000-4-3 (RS)

• EN61000-4-4 (EFT)

• EN61000-4-5 (Surge)

• EN61000-4-6 (Conducted Disturbances)

Warranty

3 years from the date of purchase.

N-Tron 1000 Series Hardware Guide 1-6

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Model 1005TX - Key Specifications

Table 6. 1005TX Key Specifications

PHYSICAL ELECTRICAL

Height 4.0” (10.16 cm) Input Voltage 10-30 VDC (Regulated)

Width 1.0” (2.54 cm) Input Current 230mA max. @ 24VDC

(Steady State)

Depth w/ typical
SFP installed

Weight 0.7 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN Rail 35 mm Input Wire Size 12-24 AWG

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 90%

Operating Altitude 0 to 10,000 ft.

3.61” (9.165 cm) Inrush Current 13 Amp/0.61 ms max. @
24VDC

1000BaseT  Cat-5e

(Non Condensing)

CONNECTORS RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX Five (5) RJ45 TX Copper

Ports

Top 1 " (2.54 cm)

Front 2 " (5.08 cm)

Model 1005TX Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment

• ANSI/ISA-12.12.01-2007 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous

(Classified) Locations Groups A, B, C, D. T4

• cUL C22.2 No. 14-M05

• cUL C22.2 No. 213-M1987 for use in Class I, Division 2 Hazardous Locations.

EMI

EN61000-6-4, EN55011 - Class A

•

• FCC Title 47, Part 15, Subpart B - Class A

• ICES-003 – Class A

N-Tron 1000 Series Hardware Guide 1-7

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

EMS

EN61000-6-2

•

• EN61000-4-2 (ESD)

• EN61000-4-3 (RS)

• EN61000-4-4 (EFT)

• EN61000-4-5 (Surge)

• EN61000-4-6 (Conducted Disturbances)

Warranty

3 years from the date of purchase.

N-Tron 1000 Series Hardware Guide 1-8

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Model 1008TX - Key Specifications

Table 7. 1008TX Key Specifications

PHYSICAL ELECTRICAL

Height 4.63” (11.76 cm) Input Voltage 10-49 VDC (Regulated)

Width 1.55” (3.94 cm) Input Current 290mA max. @ 24VDC

(Steady State)

Depth w/ typical
SFP installed

Weight 0.7 lbs (0.32 kg) Input Ripple Less than 100 mV

DIN Rail 35 mm Input Wire Size 12-24 AWG

ENVIRONMENTAL NETWORK MEDIA

Operating Temperature -40°C to 85°C 10BaseT  Cat-3

Storage Temperature -40°C to 85°C 100BaseT  Cat-5

Operating Humidity 10% to 90%(Non Condens-

Operating Altitude 0 to 10,000 ft.

4.08” (10.37 cm) Inrush Current 20 Amp/0.06 ms max. @
24VDC

1000BaseT  Cat-5e

ing)

CONNECTORS RECOMMENDED MINIMUM WIRING CLEARANCE

10/100/1000BaseTX Eight (8) RJ45 TX Copper

Ports

Top 1 " (2.54 cm)

Front 2 " (5.08 cm)

Model 1008TX Regulatory Approvals

Safety

For use in Class I, Division 2, Groups A, B, C and D Hazardous Locations.

• UL 508, Industrial Control Equipment.

• ANSI/ISA-12.12.01-2013 for use in Class I and II, Division 2 and Class III Divisions 1 and 2 Hazardous (Classi-

fied) Locations Groups A, B, C, D. T4.

• cUL C22.2 No. 14-M05

• cUL C22.2 No. 213-M1987 for use in Class I, Division 2 Hazardous Locations.

EMI

FCC Title 47, Part 15, Subpart B - Class A

•

• Industry Canada ICES-003 – Class A

• EN 55011 - Class A

• EN 61000-6-4

• EN 61000-3-2/3

N-Tron 1000 Series Hardware Guide 1-9

Introduction and Specifications Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

EMS

EN 61000-6-2

•

• EN 61000-4-2/3/4/5/6/8/11

Warranty

3 years from the date of purchase.

N-Tron 1000 Series Hardware Guide 1-10

Installation Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Section 2 Installation

Introduction

This sections contains the information and procedures necessary to unpack, inspect, install and connect the
N-Tron 1000 Series equipment.

Unpacking

Remove all the equipment from the packaging, and store the packaging in a safe place.

Inspection

Please ensure the shipping package contains the following items in undamaged condition:

1. N-Tron 1000 Series Media Converter or Ethernet Switch.

2. Product CD.

If the package contents are damaged:

1. Contact your carrier.

2. File any damage claims with the carrier.

Installing/Mounting

Read the following warning before beginning the installation:

Lire l'avertissement suivant avant de commencer l'installation:

WARNING: Never install or work on electrical equipment or cabling during peri-

ods of lightning activity. Never connect or disconnect power when hazardous
gases are present.

ALERTE: Ne jamais installer ou de travailler sur un équipement électrique ou de

câblage pendant les périodes d'activité de la foudre. Ne jamais brancher ou
débrancher l'alimentation en gaz dangereux sont présents

N-Tron 1000 Series Hardware Guide 2-11

Installation Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

DIN-Rail Mounting

a. Install the unit in a standard DIN rail. Recess the unit to allow at least 2” of horizontal clearance for CAT5e

cable bend radius or 5” of horizontal clearance for Fiber Optic cable bend radius.

b. To install the unit to 35mm industrial DIN rail,

place the top edge of the included mounting
bracket on the back of the unit against the DIN rail
at a 15° angle as shown. Rotate the bottom of the
unit to the back (away from you) until it snaps into
place.

c. To remove the unit from the 35mm industrial

DIN rail, pull forward on the unit until it disen­gages from the bottom of the DIN rail. Rotate
the bottom of the unit towards you and up at an
approximate 15° upward angle to completely
remove the unit.

URMK 1000-PM

Most Red Lion N-Tron™ products are designed to be mounted on industry standard 35mm DIN rail. However, DIN rail mount­ing may not be suitable for all applications. Our Universal Rack Mount Kit (P/N: URMK) can be used to mount the 1000 Series
enclosures to standard 19" racks, and our Panel Mount Assembly (P/N: 1000-PM) can be used to mount the 1000 Series
enclosures to a panel or any other flat surface.

N-Tron 1000 Series Hardware Guide 2-12

Installation Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Connections

Power Connection (Top View)

1. Unscrew & Remove the DC Voltage Input Plug from the top header.

2. Install the DC Power Cables into the Plug (observing polarity on unit).

3. Plug the Voltage Input Plug back into the top header.

4. Tightening torque for the terminal block power plug is 0.5 Nm/0.368 Pound Foot.

5. Verify the Power LED stays ON (GREEN).

Note: Either V1 or V2 can be connected to power for minimal operation. For redundant power opera-

tion, V1 and V2 plugs must be connected to separate DC Voltage sources. Use wire sizes of 12-24
gauge. Limit he power cord length to less than 10 meters in order to ensure optimum performance.

Recommend using 24V DC Power Supplies, similar to:

• 100-240VAC:N-Tron NTPS-24-1.3, DC 24V/1.3A

Ground Connection

N-Tron Series Switch Grounding Techniques for 1000 Series

The grounding philosophy of any control system is an integral part of the design. N-Tron series switches are
designed to be grounded, but the user has been given the flexibility to float the switch when required. The best
noise immunity and emissions (i.e. CE) are obtained when the N-Tron switch chassis is connected to earth ground
via a drain wire. Some N-Tron series switches have metal din-rail brackets that can ground the switch if the din-rail
is grounded. In some cases, N-Tron series switches with metal brackets can be supplied with optional plastic
brackets if isolation is required.

N-Tron 1000 Series Hardware Guide 2-13

Installation Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Users may run a drain wire & lug from the screw provided on the back face of the
enclosure. In the event the provided grounding screw has been lost, care should
be taken to limit the penetration of the outer skin by less than 1/4". Failure to do so
may cause irreversible damage to the internal components of the switch.

Note: Ensure the power supply is grounded properly before
applying power to the grounded switch. This can be verified by
using a voltmeter to determine that there is no voltage difference
between the power supply’s negative output terminal and the
chassis grounding point of the switch.

Drain wire with lug connecting switch chassis
to known god grounding posts.

Note: The V-legs of the power input connector are connected to the chassis internally on the
1002MC, 1003GX2 and 1005TX. Before applying power to the grounded switch, you must use a
volt meter to verify there is no voltage difference between the power supply’s negative output ter­minal and the switch chassis grounding point.

If the use of shielded cables is required, it is generally recommended to only connect the shield at one end to pre­vent ground loops and interfere with low level signals (i.e. thermocouples, RTD, etc.). Cat5e cables manufactured
to EIA-568A or 568B specifications are required for use with N-Tron series switches.

In the event all Cat5e patch cable distances are small (i.e. All Ethernet devices are located the same local cabinet
and/or referenced to the same earth ground), it is permissible to use fully shielded cables terminated to chassis
ground at both ends in systems void of low level analog signals.

N-Tron 1000 Series Hardware Guide 2-14

Installation Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Cable Connection

Cable connections are dependent on the network configuration and N-Tron 1000 Series model in use.

1. For 10Base-T ports, plug a Category 3 (or greater) twisted pair cable into the RJ45 connector.

2. For 100/1000Base-T ports, plug a Category 5e (or greater) twisted pair cable into the RJ45 connector. Con-

nect the other end to the far end station.

3. Verify that the LNK/ACT LEDs are ON once the connection has been completed.

4. To connect any other port to another Switch or Repeater, use a standard Cat5e straight through or crossover

cable.

CAUTION: Creating a port to port connection on the same switch (i.e. loop) is an illegal
operation and will create a broadcast storm which will crash the network!

ATTENTION: Création d'un port de connexion du port sur le même commutateur
(c.-à-boucle) est une opération illégale et va créer une tempête de diffusion qui va planter
le réseau!

N-Tron 1000 Series Hardware Guide 2-15

Installation Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

N-Tron 1000 Series Hardware Guide 2-16

Operation and Maintenance Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Section 3 Operation and Maintenance

Introduction

The N-Tron 1000 Series Gigabit Media Converter & Industrial Gigabit Ethernet Switch devices provide operating
status information through the LED indicators located on the front panel.

Controls and Indicators

Model 1002MC, 1003GX2, 1005TX Indicators

Table 8. Model 1002MC, 1003GX2, 1005TX Indicators (from top to bottom)

INDICATOR DESCRIPTION

LNK/ACT

SPD1000

N-Tron 1000 Series Hardware Guide 3-17

Green LED lights when power is connected

LED indicating link/activity

LED indicating 1000 Link data speed

Operation and Maintenance Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Table 9 describes the indicator states and the operating modes:

Table 9. Model 1002MC, 1003GX2, 1005TX Indicator States

INDICATOR STATE DESCRIPTION

LNK/ACT

SPD1000

ON Power is applied

OFF Power is off

ON Link established, no activity on cable

BLINKING Link established, activity on cable

OFF No link activity on cable

ON Link is operating at 1000Mbps

OFF Link is operating at 10/100Mbps

Model 1008TX Indicators

Table 10. Model 1008TX Indicators (from top to bottom)

INDICATOR DESCRIPTION

Green LED lights when power is connected

ACT

1000

3-18

LED indicating activity

LED indicating 1000 Link data speed

N-Tron 1000 Series Hardware Guide

Operation and Maintenance Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Table 11 describes the indicator states and the operating modes:

Table 11. Model 1008TX Indicator States

INDICATOR STATE DESCRIPTION

ACT

1000

ON Power is applied

OFF Power is off

ON/BLINKING Link established, activity on cable

OFF No link activity on cable

ON Link is operating at 1000Mbps

OFF Link is operating at 10/100Mbps

Maintenance

Maintenance is limited to verifying the cable interface and unit cleaning.

Verify/Troubleshoot Cable Interface

1. Make sure the (Power LED) is ON.

2. Make sure you are supplying sufficient current for the chosen switch version.

Note: The inrush current will exceed the steady state current by ~ 2X.

3. Verify that Link LEDs are ON for both ports.

4. Verify cabling used between stations.

5. Verify that cabling is Category 3 or greater for 10Mbps Operation.

Cleaning

Clean hardware only with a damp cloth.

N-Tron 1000 Series Hardware Guide 3-19

Operation and Maintenance Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

Red Lion Controls N-Tron 1000 Series Limited Warranty

Red Lion warrants to the end user that this hardware product will be free from defects in workmanship and materi­als, under normal use and service, for the applicable warranty period from the date of purchase from Red Lion or
its authorized reseller. If a product does not operate as warranted during the applicable warranty period, Red Lion
shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or
part to replace the defective item, or refund to customer the purchase price paid for the defective product. All prod­ucts that are replaced will become the property of Red Lion. Replacement products may be new or reconditioned.
Any replaced or repaired product or part has a ninety (90) day warranty or the remainder of the initial warranty
period, whichever is longer. Red Lion shall not be responsible for any custom software or firmware, configuration
information, or memory data of customer contained in, stored on, or integrated with any products returned to Red
Lion pursuant to any warranty.

OBTAINING WARRANTY SERVICE: Customer must contact Red Lion within the applicable warranty period to
obtain warranty service authorization. Dated proof of purchase from Red Lion or its authorized reseller may be
required. Products returned to Red Lion must be pre-authorized by Red Lion with a Return Material Authorization
(RMA) number marked on the outside of the package, and sent prepaid and packaged appropriately for safe ship­ment. Responsibility for loss or damage does not transfer to Red Lion until the returned item is received by Red
Lion. The repaired or replaced item will be shipped to the customer, at Red Lion's expense, not later than thirty (30)
days after Red Lion receives the product. Red Lion shall not be responsible for any software, firmware, information,
or memory date of customer contained in, stored on, or integrated with any products returned to Red Lion for
repair, whether under warranty or not.

ADVANCE REPLACEMENT OPTION: Upon registration, this product qualifies for advance replacement. A
replacement product will be shipped within three (3) days after verification by Red Lion that the product is consid­ered defective. The shipment of advance replacement products is subject to local legal requirements and may not
be available in all locations. When an advance replacement is provided and customer fails to return the original
product to Red Lion within fifteen (15) days after shipment of the replacement, Red Lion will charge customer for
the replacement product, at list price.

WARRANTIES EXCLUSIVE: IF A RED LION PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUS­TOMER'S SOLE REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR
REFUND OF THE PURCHASE PRICE PAID, AT RED LION’S OPTION. TO THE FULL EXTENT ALLOWED BY
LAW, THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, TERMS, OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS, OR CONDITIONS OF MERCHANT­ABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH
DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. RED LION NEI­THER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. RED LION
SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE
ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUS­TOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAU­THORIZED ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND
THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, POWER CUTS OR OUTAGES,
OTHER HAZARDS, OR ACTS OF GOD.

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, RED LION ALSO EXCLUDES FOR
ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEG­LIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY
KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA,
OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

3-20

N-Tron 1000 Series Hardware Guide

Operation and Maintenance Revised 2015-03-24

Buy: www.ValinOnline.com | Phone [phone] | Email: [e-mail]

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF N­TRON OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES,
AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT
N-TRON'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REM­EDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

DISCLAIMER: Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or
the limitation of incidental or consequential damages for certain products supplied to consumers or the limitation of
liability for personal injury, so the above limitations and exclusions may be limited in their application to you. When
the implied warranties are not allowed to be excluded in their entirety, they will be limited to the duration of the
applicable written warranty. This warranty gives you specific legal rights which may vary depending on local law.

GOVERNING LAW: This Limited Warranty shall be governed by the laws of the State of Delaware, U.S.A.

N-Tron 1000 Series Hardware Guide 3-21