Red Lion NT100 User Manual

Bulletin No. NT100-X

C

US

Drawing No. LP0871
Effective 06/11

Tel [phone]
Fax [phone]
www.redlion.net

MODEL NT100 SERIES – UNMANAGED INDUSTRIAL ETHERNET SWITCHES

 UNMANAGED SWITCH REQUIRES NO CONFIGURATION
 SUPPORTS 10/100 MBPS NETWORKS
 AUTO HALF/FULL DUPLEX NEGOTIATION
 REDUNDANT POWER INPUTS
 AUTO-CROSSING DETECTION SUPPORTS STANDARD AND

CROSSOVER ETHERNET CABLES

C

LISTED

U

R

FOR USE IN HAZARDOUS LOCATIONS:

US

L

Class I, Division 2, Groups A, B, C, and D
or unclassified or non-hazardous locations only.

65SN

GENERAL DESCRIPTION

The NT series is a range of compact IEEE 802.3 layer two network switches
with automatic speed, duplex and cable sensing. The series features ultra-robust
construction, capable of withstanding environmental extremes for use in mission
critical applications.

These affordable, Class I, Division 2 switches feature redundant power
inputs, hardened metal enclosures, and 16 kV port protection. Each switch is
capable of auto negotiating 10/100 Mb and half/full duplex communications.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the
literature or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF
COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I,
DIVISION 2

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT

For 108TX: Use 60/75°C rated copper wire, (0.22Nm) 2 inch-lbs. tightening

For 104TX & 105TX: Use 95°C rated copper wire, (0.22Nm) 2 inch-lbs.

EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA
IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT
UNLESS POWER HAS BEEN SWITCHED OFF OR AREA IS KNOWN TO BE
NON-HAZARDOUS.

torque for field installed connectors.

tightening torque for field installed connectors.

SPECIFICATIONS

1. POWER: 10-30 VDC
NT104TX/NT105TX: 215 mA max. @ 24VDC
NT108TX: 250 mA max. @ 24VDC

2. LEDs:

3. ENVIRONMENTAL CONDITIONS:

4. CONSTRUCTION: Brushed aluminum housing

5. CONNECTIONS:

6. MOUNTING: Snaps onto standard DIN style top hat (T) profile mounting

7. CERTIFICA TIONS AND COMPLIANCES:

8. WEIGHT:

1

LED COLOR DESCRIPTION

LNK/ACT

ON Power is Applied.
OFF Power is OFF.
ON Link established, no Activity on cable.
BLINKING Link established, Activity on cable
OFF No link activity on cable.
ON Link is 100Mbps.

SPD

OFF Link is 10Mbs.

Operating Temperature Range:
NT104TX/NT105TX: -40 to +80 °C
NT108TX: -40 to +70 °C
Storage Temperature Range: -40 to +85 °C
Operating Humidity: 10-95%, non-condensing
Altitude: Up to 3000 meters.

Power: Removable wire clamp screw terminal block.
Wire Gage Capacity: 28 AWG to 16 AWG
Torque: 2 in/lb (0.22 Nm)
Ethernet: RJ-45 UTP ports

rail according to EN50022 -35 x 7.5 and -35 x 15.

UL Listed (N-Tron Incorporated, Part numbers 104TX, 105TX, 108TX. File

#E214222)

Safety: Suitable for use in Class I, Division 2, Groups A, B, C and D

Hazardous locations, or non-hazardous locations only.

Immunity to Industrial Locations:

EMI: EN61000-6-4, EN55011 - Class A

FCC Title 47, Part 15, Subpart B - Class A
ICES-003 – Class A

EMS: EN61000-6-2

EN61000-4-2 (ESD)
EN61000-4-3 (RS)
EN61000-4-4 (EFT)
EN61000-4-5 (Surge)
EN61000-4-6 (Conducted Disturbances)

NT104TX/NT105TX: 0.6 lbs. (0.27 Kg)
NT108TX0: 0.7 lbs. (0.31 Kg)

DIMENSIONS In inches (mm)

Powered by

1.49

(37.85)

PWR

Powered by

1.49

(37.85)

PWR

1

2 3

4 5

2.87

(72.90)

104TX

1 2

3 4

2.87

(72.90)

105TX

DIMENSIONS In inches (mm)

Powered by

3.50

(88.90)

PWR

1 2

3 4

4.22

(107.19)

3.53

(89.62)

4.22 (107.19)

3.97 (100.95)

3.53 (89.62)

3.17

(80.52)

3.50

(88.90)

5 6

7 8

3.53

(89.62)

108TX

1.49

(37.85)

POWER

Either V1 or V2 can be connected to power for minimal operation. For
redundant power operation, V
Voltage sources. Use wire sizes of 16-28 gauge.

NOTE: Must use an NEC Class 2 or Limited

Power Source (LPS) rated power supply.

and V2 plugs must be connected to separate DC

1

3.80

(96.52)

1.71

(43.43)

MOUNTING

To install the plastic clip units to 35mm industrial DIN rail, place the top edge
of the included mounting bracket on the back of the unit against the DIN rail at
a 15° angle as shown. Rotate the bottom of the unit to the back (away from you)
until it snaps into place.

2

To remove the unit from the DIN rail, place a flat head screwdriver into the
release clip found at the bottom of the unit, and apply downward force on the
clip until it disengages the bottom of the unit from the DIN rail. Rotate the
bottom of the unit towards you and up at an approximate 15° upward angle to
completely remove the unit.

NT series switches are designed to be grounded, but the user has been given
the flexibility to float the unit when required. The best noise immunity and
emissions are obtained when the unit’s chassis is connected to earth ground via
a drain wire.

Users may run a drain wire & lug from the screw provided on the back face
of the enclosure. In the event the provided grounding screw has been lost, care
should be taken to limit the penetration of the outer skin by less than 1/4".
Failure to do so may cause irreversible damage to the internal components of the
switch.

Note: Ensure the power supply is grounded properly before applying power
to the grounded switch. This may be verified by using a voltmeter to determine

TROUBLESHOOTING

For further technical assistance, contact technical support at the appropriate company numbers listed.

ORDERING INFORMATION

MODEL NO. DESCRIPTION PART NUMBER

4-Port Ethernet Switch NT104TX0

NT100

5-Port Ethernet Switch NT105TX0
8-Port Ethernet Switch NT108TX0

that there is no voltage difference between the power supply’s negative output
terminal and the chassis grounding point of the switch.

As an alternative grounding method, both V- legs of the power input
connector are connected to the chassis internally on the PCB. Connecting a
drain wire to earth ground from one of the V- terminal plugs will ground the
switch and the chassis. The power leads from the power source should be
limited to 3 meters or less in length.

If the use of shielded cables is required, it is generally recommended to only
connect the shield at one end to prevent ground loops and interference with low
level signals (i.e. thermocouples, RTD, etc.). Cat5e cables manufactured to
EIA-568A or 568B specifications are required for use with NT series switches.

3

LIMITED WARRANTY

The Company warrants the products it manufactures against defects in materials and workmanship for a
period limited to two years from the date of shipment, provided the products have been stored, handled,
installed, and used under proper conditions. The Company’s liability under this limited warranty shall
extend only to the repair or replacement of a defective product, at The Company’s option. The Company
disclaims all liability for any affi rmation, promise or representation with respect to the products.

The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products containing
components manufactured by RLC and based upon personal injuries, deaths, property damage, lost profi ts,
and other matters which Buyer, its employees, or sub-contractors are or may be to any extent liable,
including without limitation penalties imposed by the Consumer Product Safety Act (P.L. 92-573) and
liability imposed upon any person pursuant to the Magnuson-Moss Warranty Act (P.L. 93-637), as now in
effect or as amended hereafter.

No warranties expressed or implied are created with respect to The Company’s products except those
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained herein
and relies on no other warranties or affi rmations.

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]

Red Lion Controls

Europe

Printerweg 10

NL - 3821 AD Amersfoort

Tel [phone]

Fax [phone]

Red Lion Controls

India

54, Vishvas Tenement

GST Road, New Ranip,

Ahmedabad-382480 Gujarat, India

Tel [phone]

Fax [phone]

4

Red Lion Controls

China

Unit 101, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel [phone]

Fax [phone]