Red Lion G15 User Manual

Bulletin No. GRAPH-C

Drawing No. LP0918

Released 04/14

Tel [phone]

Fax [phone]

www.redlion.net

GRAPHITE™ SERIES - OPERATOR INTERFACE TERMINALS WITH
PLUG-IN I/O MODULE CAPABILITY

z PROTOCOL CONVERSION FEATURE CONVERTS NUMEROUS

PROTOCOLS SIMULTANEOUSLY

z OVER 250 BUILT-IN DRIVERS ALLOWS EASY DATA MAPPING TO

PLCS, PCS, AND SCADA SYSTEMS

z BUILT-IN WEB SERVER ALLOWS REMOTE VIEW OR CONTROL

FROM ANY INTERNET CONNECTED PC OR SMART PHONE

z SYNCS DATA LOGS TO FTP SERVERS AND MICROSOFT SQL

SERVER

z PROVIDES EMAIL AND SMS TEXT MESSAGE ALERTS

z CONFIGURED USING CRIMSON® 3 SOFTWARE

z UP TO 4 FULLY ISOLATED SERIAL COMMUNICATION PORTS,

(2 RS-232 AND 1 RS-422/485)

U

R

C

US LISTED

L

IND. CONT. EQ.

34AD

z 10 BASE T/100 BASE-TX ETHERNET CONNECTION CAN

CONNECT TO AN UNLIMITED NUMBER OF DEVICES VIA TEN
PROTOCOLS SIMULTANEOUSLY

z EASY TO ADD I/O CAPABILITY WITH GRAPHITE PLUG-IN

MODULES

z ALUMINUM CASE CONSTRUCTION FOR BOTH THE OPERATOR

INTERFACE TERMINAL AND THE I/O MODULES

®

GENERAL DESCRIPTION

The Graphite™ Series merges two of our most highly successful product
platforms into a single, extremely flexible solution. The nexus of the product is
the operator interface panel which offers the award winning technology of our
G3 HMI Series including protocol conversion, data logging and remote access.
Programming the unit is easy using drag and drop selection within our Crimson
3 software allowing complete set-up in minutes. Add to all that capability, plug­in modules which provide I/O functions within the framework of the operator
interface panel. The I/O modules are similar to our Modular Controller Series
product providing easy interface of sensors, discreet outputs and communication
modules. The result is a complete industrial solution that connects, monitors,
and controls while providing real time displays.

The operator interface panels are available in 5 different panel sizes; 7", 9",
10", 12" and 15", with the 7", 9" and 12" displays in the wide screen format. The
displays are full color touch panels in VGA, SVGA or XGA formats and operate
as full touchscreens. The all-aluminum construction provides very robust
packaging that can withstand even the most demanding environments. If your
application calls for outdoor use, we have two models, 7"and 10" that are
designed for just that requirement.

The units are able to communicate with many types of hardware simultaneously
using high-speed RS-232/485 communication ports and Ethernet 10 Base T/100
Base-TX communications. Currently over 250 drivers are selectable in the
Crimson Software which allows easy data mapping to PLCs, PCs, and SCADA
Systems. In addition, the Graphite Series features USB host capability for fast
downloads of configuration files and access to trending and data logging
information.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the
manual or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.

Do not use the controller to directly command motors, valves, or other
actuators not equipped with safeguards. To do so can be potentially harmful to
persons or equipment in the event of a fault to the controller.

CAUTION: Risk Of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

CONTENTS OF PACKAGE

- Operator Interface.

- Panel gasket.

- Hardware packet for mounting unit into panel.

- Terminal block for connecting power.

1

SpecificationS

1. POWER REQUIREMENTS: +24 VDC ±20%
Must use a Class 2 circuit according to National Electrical Code (NEC),

NFPA-70 or Canadian Electrical Code (CEC), Part I, C22.1 or a Limited
Power Supply (LPS) according to IEC 60950-1 or Limited-energy circuit
according to IEC 61010-1.
Power connection via removable three position terminal block.

G07C G07S G09 G10C/R G10S G12 G15

Typical Power

HMI only:

Maximum Power

HMI only:

Maximum Power

HMI w/ Module(s):

9 W 10 W 13 W 12 W 18 W 16 W 20 W

16 W 17 W 20 W 19 W 24 W 23 W 27 W

37 W 38 W 45 W 48 W 53 W 56 W 60 W

2. BATTERY: Lithium coin cell. Typical lifetime of 6 years, nominal.

3. LCD DISPLAY: See Table below for detailed display specifications.

4. TOUCHSCREEN: Resistive analog

5. MEMORY:

On Board User Memory: 256 Mbyte of non-volatile Flash memory.
Memory Card: SD slot accepts standard capacity cards up to 2Gbyte.

6. COMMUNICATION CAPABILITIES:
USB Port: Adheres to USB specification 2.0 (high speed, full speed) only

using Type B connection.

WARNING - Do not connect or disconnect cables while
power is applied unless area is known to be non-hazardous.
USB port is for system set-up and diagnostics and is not
intended for permanent connection.

USB Host Ports: Comply with Universal Serial Bus Specification Rev 2.0.

Support data transfers at (high speed, full speed). Hardware over current
protected (0.5 A max per port).

Serial Ports: Ports are individually isolated. Format and Baud Rates for each

port are individually software programmable up to 115,200 baud.
PGM Port: RS232 port via RJ12.
COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12.
DH485 TXEN: Transmit enable; open collector, VOH = 15 VDC,

VOL = 0.5 V @ 25 mA max.

Ethernet Port: 10 BASE-T / 100 BASE-TX

RJ45 jack is wired as a NIC (Network Interface Card).
Isolation from Ethernet network to Graphite operator interface: 1500 Vrms

7. ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: -20 to 60 °C
Storage Temperature Range: -20 to 70 °C
Vibration to IEC 68-2-6: Operational 5-500 Hz, 4 g
Shock to IEC 68-2-27: Operational 40 g (10 g, modules w/relays)
Operating and Storage Humidity: 0 to 85% max. RH non-condensing
Altitude: Up to 2000 meters

8. CERTIFICATIONS AND COMPLIANCES:

CE Approved

EN 61326-1 Immunity to Industrial Locations
Emission CISPR 11 Class A
IEC/EN 61010-1

RoHS Compliant
UL Listed: File #E302106
Type 4X Indoor / IP66 Enclosure rating (Face only) for all models
Type 4X Outdoor Enclosure rating (Face only) for GxxSxxxx models

9. CONNECTIONS: High compression cage-clamp terminal block
Wire Strip Length: 0.3" (7.5 mm)
Wire Gauge Capacity: One 14 AWG (2.55 mm) solid,

two 18 AWG (1.02 mm) or four 20 AWG (0.61 mm)

10. CONSTRUCTION: Cast aluminum enclosure with NEMA 4X/IP66 rating
for indoor use only when correctly fitted with the gasket provided. Installation
Category II, Pollution Degree 2.

11. MOUNTING REQUIREMENTS: Maximum panel thickness is 0.188"
(4.78 mm) with removable foot, or 0.375" (9.53 mm) without foot. For
NEMA 4X/IP66 sealing, a steel panel with a minimum thickness of 0.125"
(3.17 mm) is recommended.
Maximum Mounting Screw Torque: 6.0 lbf inch (96 ozf inch)

12. WEIGHT:
G07: 2.26 lb. (1.03 Kg)
G09: 3.39 lb. (1.54 Kg)
G10: 4.8 lb. (2.18 Kg)
G12: 5.06 lb. (2.29 Kg)
G15: 7.73 lb. (3.5 Kg)

LCD DISPLAY:

G07C G07S G09 G10C G10R G10S G12 G15

SIZE 7 - inch 7 - inch 9 - inch 10 - inch 10 - inch 10 - inch 12 - inch 15 - inch

COLORS

PIXELS

BRIGHTNESS

BACKLIGHT (HR TYP.) *

BACKLIGHT TYPE

* Lifetime at room temperature (25°C)

WVGA, 16 M WVGA, 16 M WVGA, 16 M VGA, 16 M SVGA, 16 M VGA, 16 M WXGA, 16 M XGA, 16 M

800 X 480 800 X 480 800 X 480 640 X 480 800 X 600 640 X 480 1280 X 800 1024 X 768

500 cd/m21000 cd/m2400 cd/m2450 cd/m2400 cd/m21500 cd/m2400 cd/m2400 cd/m

40,000 40,000 70,000 70,000 70,000 35,000 70,000 70,000

LED LED LED LED LED LED LED LED

2

2

DimenSionS in inches (mm)

G07

G09

G10

5.51

(139.9)

6.47

(164.4)

7.70 (195.5) 2.00 (50.8)

Module sold

separately

10.06 (255.6)

10.84 (275.2)

2.06 (52.4)

Module sold

separately

2.97 (76)

2.97 (76)

2.06 (52.4)

7.9 (202)

(MOUNTING CLIPS INSTALLED)

10.3 (262)

(MOUNTING CLIPS INSTALLED)

11.1 (281)

5.7

(146)

6.7

(171)

G12

G15

8.20

(208.3)

8.57

(217.7)

12.10 (307.3)

14.03 (356.3)

2.97 (76)

Module sold

separately

2.06 (52.4)

2.97 (76)

Module sold

separately

2.14 (54.3)

2.97 (76)

8.8

(224)

(MOUNTING CLIPS INSTALLED)

12.3 (314)

8.4

(215)

(MOUNTING CLIPS INSTALLED)

14.3 (363)

11.10

(281.8)

11.3

(288)

Module sold

separately

(MOUNTING CLIPS INSTALLED)

3

operator interface inStallation

FOOT MAY BE REMOVED
FOR THICKER PANEL
INSTALLATIONS

MOUNTING INSTRUCTIONS

This operator interface is primarily designed for
through-panel mounting. Four VESA mount tapped
screw-holes (M4 x 0.7, 5 mm deep) are present on the
rear of the panel to allow for stand or wall mounting.
Care should be taken to remove any loose material from
the mounting cut-out to prevent that material from falling

into the operator interface during installation. A gasket is
provided to enable sealing to NEMA 4X/IP66
specification. Install the mounting clips provided and
tighten to 6.0 pound-force inch (96 ounce-force inch)
evenly for uniform gasket compression.

ALL NONINCENDIVE CIRCUITS MUST BE
WIRED USING DIVISION 2 WIRING
METHODS AS SPECIFIED IN ARTICLE 501-4
(b), 502-4 (b), AND 503-3 (b) OF THE
NATIONAL ELECTRICAL CODE, NFPA 70
FOR INSTALLATION WITHIN THE UNITED
STATES, OR AS SPECIFIED IN SECTION
19-152 OF CANADIAN ELECTRICAL CODE
FOR INSTALLATION IN CANADA.

G07

G09

PANEL CUT-OUT

7.060 (179.3)

4X R.10 (2.5)

MAX.

All tolerances ±.059" (±1.5 mm)

PANEL CUT-OUT

9.423 (239.3)

4X R.10 (2.5)

MAX.

4.869

(123.7)

5.832

(148.1)

VESA MOUNT (MIS-D 75) DIMENSIONS

1.48 (37.5)

2.95 (75)

2.95
(75)

1.73
(44)

VESA MOUNT (MIS-D 75) DIMENSIONS

1.48 (37.5)

2.95 (75)

2.95
(75)

All tolerances ±.059" (±1.5 mm)

1.77
(45)

44

10.197 (259.0)

A

G10

A

PANEL CUT-OUT

4X R.10 (2.5)

MAX.

ll tolerances ±.059" (±1.5 mm)

VESA MOUNT (MIS-D 75) DIMENSIONS

1.48 (37.5)

2.95 (75)

2.95
(75)

7.931

(201.4)

.87

(22.1)

G12

PANEL CUT-OUT

11.458 (291.0)

4X R.10 (2.5)

MAX.

ll tolerances ±.059" (±1.5 mm)

G15

PANEL CUT-OUT

13.390 (340.1)

VESA MOUNT (MIS-D 75) DIMENSIONS

1.48 (37.5)

2.95 (75)

2.95
(75)

7.561

(192.0)

1.08

(27.4)

VESA MOUNT (MIS-D 75) DIMENSIONS

1.48 (37.5)

2.95 (75)

4X R.10 (2.5)

MAX.

All tolerances ±.059" (±1.5 mm)

2.95
(75)

10.457
(265.6)

.09

(2.4)

5

CONNECTING TO EARTH GROUND

The protective conductor terminal is bonded to conductive
parts of the equipment for safety purposes and must be
connected to an external protective earthing system.

The third pin of the power connector of the G07 is chassis ground for the unit.

Your unit should be connected to earth ground (protective earth).

The chassis ground is not connected to signal common of the unit.
Maintaining isolation between earth ground and signal common is not required
to operate your unit. But, other equipment connected to this unit may require
isolation between signal common and earth ground. To maintain isolation

between signal common and earth ground care must be taken when connections
are made to the unit. For example, a power supply with isolation between its

signal common and earth ground must be used. Also, plugging in a USB cable
may connect signal common and earth ground.

1

USB’s shield may be connected to earth ground at the host. USB’s shield in

turn may also be connected to signal common.

1

POWER SUPPLY REQUIREMENTS

The Graphite panel requires a 24 VDC power supply. Your unit may draw
considerably less than the maximum rated power depending upon the features
being used. As additional features are used your unit will draw increasing
amounts of power. Items that could cause increases in current are modules,
additional on-board communications, SD card, and other features programmed
through Crimson.

In any case, it is very important that the power supply is mounted correctly if
the unit is to operate reliably. Please take care to observe the following points:

– The power supply must be mounted close to the unit, with usually not more

than 6 feet (1.8 m) of cable between the supply and the operator interface.
Ideally, the shortest length possible should be used.

– The wire used to connect the operator interface’s power supply should be

at least 22-gage wire suitably rated for the temperatures of the environment
to which it is being installed. If a longer cable run is used, a heavier gage
wire should be used. The routing of the cable should be kept away from
large contactors, inverters, and other devices which may generate
significant electrical noise.

– A power supply with an NEC Class 2 or Limited Power Source (LPS) and

SELV rating is to be used. This type of power supply provides isolation to
accessible circuits from hazardous voltage levels generated by a mains
power supply due to single faults. SELV is an acronym for “safety extra­low voltage.” Safety extra-low voltage circuits shall exhibit voltages safe
to touch both under normal operating conditions and after a single fault,
such as a breakdown of a layer of basic insulation or after the failure of a
single component has occurred.

effective. The following EMI suppression devices (or equivalent) are
recommended:

Fair-Rite part number 0443167251 (RLC part number FCOR0000)
Line Filters for input power cables:

Schaffner # FN2010-1/07 (Red Lion Controls # LFIL0000)

6. To protect relay contacts that control inductive loads and to minimize radiated
and conducted noise (EMI), some type of contact protection network is
normally installed across the load, the contacts or both. The most effective
location is across the load.
a. Using a snubber, which is a resistor-capacitor (RC) network or metal oxide

varistor (MOV) across an AC inductive load is very effective at reducing
EMI and increasing relay contact life.

b. If a DC inductive load (such as a DC relay coil) is controlled by a transistor

switch, care must be taken not to exceed the breakdown voltage of the
transistor when the load is switched. One of the most effective ways is to
place a diode across the inductive load. Most RLC products with solid state
outputs have internal zener diode protection. However external diode
protection at the load is always a good design practice to limit EMI.
Although the use of a snubber or varistor could be used.
RLC part numbers: Snubber: SNUB0000
Varistor: ILS11500 or ILS23000

7. Care should be taken when connecting input and output devices to the
instrument. When a separate input and output common is provided, they
should not be mixed. Therefore a sensor common should NOT be connected
to an output common. This would cause EMI on the sensitive input common,
which could affect the instrument’s operation.

Visit RLC’s web site at http://www.redlion.net/Support/InstallationConsiderations.

html for more information on EMI guidelines, Safety and CE issues as they
relate to Red Lion Controls products.

I/O MODULE INSTALLATION

Modules must be installed beginning with slot 1 (left-most slot), with no

empty slots between the modules, and the order must match the modules order
in the Crimson database. Torque screws to 6.0 pound-force inch (96 ounce-force
inch).

WARNING: Disconnect all power
to the unit before installing or
removing modules.

EMC INSTALLATION GUIDELINES

Although Red Lion Controls Products are designed with a high degree of
immunity to Electromagnetic Interference (EMI), proper installation and wiring
methods must be followed to ensure compatibility in each application. The type
of the electrical noise, source or coupling method into a unit may be different
for various installations. Cable length, routing, and shield termination are very
important and can mean the difference between a successful or troublesome
installation. Listed are some EMI guidelines for a successful installation in an
industrial environment.

1. A unit should be mounted in a metal enclosure, which is properly connected

to protective earth.

2. Use shielded cables for all Signal and Control inputs. The shield connection

should be made as short as possible. The connection point for the shield

depends somewhat upon the application. Listed below are the recommended

methods of connecting the shield, in order of their effectiveness.

a. Connect the shield to earth ground (protective earth) at one end where the

unit is mounted.

b. Connect the shield to earth ground at both ends of the cable, usually when

the noise source frequency is over 1 MHz.

3. Never run Signal or Control cables in the same conduit or raceway with AC

power lines, conductors, feeding motors, solenoids, SCR controls, and

heaters, etc. The cables should be run through metal conduit that is properly

grounded. This is especially useful in applications where cable runs are long

and portable two-way radios are used in close proximity or if the installation

is near a commercial radio transmitter. Also, Signal or Control cables within

an enclosure should be routed as far away as possible from contactors, control

relays, transformers, and other noisy components.

4. Long cable runs are more susceptible to EMI pickup than short cable runs.

5. In extremely high EMI environments, the use of external EMI suppression

devices such as Ferrite Suppression Cores for signal and control cables is

REMOVE RUBBER
MODULE PLUG

6

TX

5V

8

1

7

2

TxB

TxA

130K

130K

5

TxEN (OC)

RX

130K

5V

130K

RxB

4

RxA

3

COMM

6

TxEN (OC)

TX/RX

130K

5

TxA

2

8

130K

5V

7

1

TxB

6 COMM

communicating With the graphite

CONFIGURING GRAPHITE

The Graphite is configured using Crimson® software. Crimson is available as
a free download from Red Lion’s website. Updates to Crimson for new features
and drivers are posted on the website as they become available. By configuring
the Graphite using the latest version of Crimson, you are assured that your unit
has the most up to date feature set. Crimson® software can configure the Graphite
through the RS232 PGM port, USB port, or SD card.

The USB port is connected using a standard USB cable with a Type B
connector. The driver needed to use the USB port will be installed with Crimson.

The RS232 PGM port uses a programming cable made by Red Lion to connect
to the DB9 COM port of your computer. If you choose to make your own cable,
use the “Port Pin Out Diagram” that corresponds to your specific model for
wiring information.

The SD card can be used to program a Graphite by placing a configuration file
and firmware on the SD card. The card is then inserted into the target Graphite
and powered. Refer to the Crimson literature for more information on the proper
names and locations of the files.

USB, DATA TRANSFERS FROM THE SD
CARD

WARNING - DO NOT CONNECT OR DISCONNECT CABLES
WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE
NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND
DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT
CONNECTION.

In order to transfer data from the SD card via the USB port, a driver must be
installed on your computer. This driver is installed with Crimson and is located
in the folder C:\Program Files\Red Lion Controls\Crimson 3.0\Device\ after
Crimson is installed. This may have already been accomplished if your Graphite
was configured using the USB port.

Once the driver is installed, connect the Graphite to your PC with a USB
cable, and follow “Mounting the SD” instructions in the Crimson 3 user manual.

ETHERNET COMMUNICATIONS

Ethernet communications can be established at either 10 BASE-T or 100
BASE-TX. The Graphite unit’s RJ45 jack is wired as a NIC (Network Interface
Card). For example, when wiring to a hub or switch use a straight-through cable,
but when connecting to another NIC use a crossover cable.

The Ethernet connector contains two LEDs. A yellow LED in the upper right,
and a green LED in the upper left. The LEDs represent the following statuses:

LED COLOR DESCRIPTION

YELLOW solid Link established.

YELLOW flashing Data being transferred.

GREEN (OFF) 10 BASE-T Communications

GREEN (ON) 100 BASE-TX Communications

On the rear of each unit is a unique 12-digit MAC address and a block for
marking the unit with an IP address. Refer to the Crimson manual and Red
Lion’s website for additional information on Ethernet communications.

RS232 PORTS

The Graphite has two RS232
ports. There is the PGM port and the
COMMS port. Although only one of
these ports can be used for
programming, both ports can be used
for communications with a PLC.

The RS232 ports can be used for
either master or slave protocols with
any Graphite configuration.

Graphite RS232 to a PC

Gxx: RJ12 Name PC: DB9 Name

4 COMM 1 DCD

5 Tx 2 Rx

2 Rx 3 Tx

N/C 4 DTR

3 COMM 5 GND

N/C 6 DSR

1 CTS 7 RTS

6 RTS 8 CTS

N/C 9 RI

USB HOST LEDS

COLOR STATUS

OFF Not operational

RED Error

GREEN Normal operation

INSERTION/REMOVAL OF THE SD CARD

Insert the SD card into the slot provided with the card oriented as shown. The
card is inserted properly when the end of the card is flush with the Graphite
case. To remove the SD card, push in slightly on the card.

CABLES AND DRIVERS

Red Lion has a wide range of cables and drivers for use with many different
communication types. A list of these drivers and cables along with pin outs is
available from Red Lion’s website. New cables and drivers are added on a
regular basis. If making your own cable, refer to the “Port Pin Outs” that
corresponds to your specific model for wiring information.

RS422/485 COMMS PORT

The Graphite has one RS422/485 port. This port can be configured to act as

either RS422 or RS485.

RS422/485 4-WIRE

CONNECTIONS

Note: All Red Lion devices connect A to A and B to B. Refer to www.redlion.net

for additional information.

7

7

RS485 2-WIRE

CONNECTIONS

Examples of RS485 2-Wire Connections DH485 COMMUNICATIONS

Graphite to Red Lion RJ11

Gxx:RJ45 Name RLC:RJ11 Name

5 TxEN 2 TxEN

6 COMM 3 COMM

1 TxB 5 B-

2 TxA 4 A+

Graphite to Modular Controller

Gxx Name

Modular

Controller

Name

1,4 TxB 1,4 TxB

4,1 RxB 4,1 RxB

2,3 TxA 2,3 TxA

3,2 RxA 3,2 RxA

5 TxEN 5 TxEN

6 COMM 6 COMM

7 TxB 7 TxB

8 TxA 8 TxA

G07 PORT PIN OUTS

USB

POWER

-

+

DEVICE

USB HOST

The Graphite’s RS422/485 COMMS port can also be used for Allen Bradley

DH485 communications.

WARNING: DO NOT use a

standard DH485 cable to
connect this port to Allen
Bradley equipment. A cable
and wiring diagram are
available from Red Lion.

RS232 RS232

ETHERNET

PORT A (PGM)

RS485

PORT A

PORT B

Graphite to AB SLC 500

RJ45: RLC Name RJ45: A-B Name

1 TxB 1 A

2 TxA 2 B

3, 8 RxA - 24V

4, 7 RxB - COMM

5 TxEN 5 TxEN

6 COMM 4 SHIELD

4, 7 TxB - COMM

3, 8 TxA - 24V

+DC VOLTAGE

COMMON

CHASSIS

1

2

3

POWER

CONNECTOR

CHASSIS

COMMON

+DC VOLTAGE

1

2

3

USB

TYPE B

USB

TYPE B

-

+

AUXILIARY

ETHERNET

[OPTIONAL]

USBPOWER

DEVICE

(NIC)

STATUS

PORT A

PORT B

USB HOST

STATUS

ETHERNET

(NIC)

STATUS

G09 PORT PIN OUTS

AUXILIARY
ETHERNET

PORT A

PORT B

USB HOST

USB HOST

ETHERNET

STATUS

ETHERNET

(NIC)

COMM

COMM

RTS (PIN 6)

Tx

Rx

RS232

PGM PORT

RS232 RS232

PORT A (PGM)

RTS (PIN 6)TxCTS (PIN 1)

COMM

TxA (PIN 8)

CTS (PIN 1)

TxB

RxB

TxENTxTxA

RS485 RS232

RS485

PORT BPORT A

COMM

Rx

COMM

TxA (PIN 8)

COMM

TxB

TxB (PIN 1)

RxA

RxB

TxEN

RxA

RTS (PIN 6)

COMMS PORTCOMMS PORT

RTS (PIN 6)RxCOMMTxCOMM

TxB (PIN 1)

TxA

COMM

COMM

CTS (PIN 1)

Rx

CTS (PIN 1)

POWER

CONNECTOR

RS232 RS485 RS232

COMMS PORTPGM PORT COMMS PORT

88

G10 PORT PIN OUTS

USBPOWER

-

+

DEVICE

+DC VOLTAGE

1

2

TYPE B

3

USB

CHASSIS

COMMON

AUXILIARY
ETHERNET

(NIC)

[OPTIONAL]

AUXILIARY
ETHERNET

PORT A

PORT B

USB HOST

STATUS

STATUS

USB HOST

ETHERNET

ETHERNET

(NIC)

RS232 RS232

RS485

PORT A (PGM)

COMM

RTS (PIN 6)TxCTS (PIN 1)

Rx

COMM

PORT BPORT A

TxA (PIN 8)

TxB

COMM

TxEN

RxB

TxB (PIN 1)

RxA

TxA

RTS (PIN 6)RxCOMMTxCOMM

CTS (PIN 1)

POWER

CONNECTOR

COMMON

+DC VOLTAGE

123

POWER

CONNECTOR

RS232 RS485 RS232

COMMS PORTPGM PORT COMMS PORT

G12 PORT PIN OUTS

RS485

PORT B

AUXILIARY
ETHERNET

PORT A

PORT B

USB HOST

STATUS

STATUS

USB HOST

ETHERNET

ETHERNET

(NIC)

RS232

PORT A (PGM)

RTS (PIN 6)TxCTS (PIN 1)

RS485

PORT A

COMM

COMM

RS232

PORT B

TxB

COMM

TxEN

TxA

RxB

RxARxRTS (PIN 6)

Rx

TxA (PIN 8)

RS232 RS485 RS232

TxB (PIN 1)

COMMTxCOMM

CTS (PIN 1)

USB

POWER

-

+

DEVICE

USB

CHASSIS

TYPE B

TxB

TxA (PIN 8)

TxEN

COMM

RxB

TxB (PIN 1)

TxA

RxA

AUXILIARY
ETHERNET

(NIC)

[OPTIONAL]

AUXILIARY

RS485 COMMS PORTCOMMS PORTPGM PORT

COMMS PORT

[OPTIONAL]

G15 PORT PIN OUTS

COMMON

+DC VOLTAGE

1

2

POWER

CONNECTOR

POWER

-

USB

+

DEVICE

RS485

PORT B

AUXILIARY
ETHERNET

USB HOST

ETHERNET

RS232

PORT A (PGM)

RS485

PORT A

RS232

PORT B

PORT A

PORT B

USB

CHASSIS

TYPE B

3

TxB

TxA (PIN 8)

TxEN

COMM

RxB

TxB (PIN 1)

TxA

RxA

AUXILIARY
ETHERNET

(NIC)

USB HOST

STATUS

STATUS

ETHERNET

(NIC)

COMM

RTS (PIN 6)TxCTS (PIN 1)

Rx

COMM

TxA (PIN 8)

TxB

COMM

TxA

RxB

TxEN

RxARxRTS (PIN 6)

TxB (PIN 1)

COMMTxCOMM

CTS (PIN 1)

[OPTIONAL]

AUXILIARY

RS485 COMMS PORTCOMMS PORTPGM PORT

COMMS PORT

RS232 RS485 RS232

[OPTIONAL]

9

SoftWare/unit operation

+

-

CRIMSON® SOFTWARE

Crimson® software is available as a free download from Red Lion’s website,
see “Ordering Information” for part number. The latest version of the software
is always available from the website, and updating your copy is free.

DISPLAY

This operator interface uses a liquid crystal display (LCD) for displaying text
and graphics. The display utilizes an LED backlight for lighting the display. The
backlight can be dimmed for low light conditions.

The LED backlight has a limited lifetime. Backlight lifetime is based upon
the amount of time the display is turned on at full intensity. Turning the
backlight off when the display is not in use can extend the lifetime of your
backlight. This can be accomplished through the Crimson® software when
configuring your unit.

FACTORY RESET BUTTON

The factory reset button located in the lower right area of the rear panel can
be used to clear databases from Graphite units using the following steps:

1. Disconnect power to the unit.

2. Using a thin probe (pin or paperclip, etc), press and hold the reset button and

re-apply power to the unit.

3. Continue to hold the reset button until instructions appear on the Graphite

screen (~10 seconds), then release the reset button.

4. Touch the left-hand side of the Graphite screen to clear the database.

TOUCHSCREEN

This operator interface utilizes a resistive analog touchscreen for user input.
The unit will only produce an audible tone (beep) when a touch on an active
touchscreen cell is sensed. The touchscreen is fully functional as soon as the
operator interface is initialized, and can be operated with gloved hands.

TOUCH ICONS

There are user programmable soft keys below the display area (See figure).
These softkeys have dead-front icons and have programmable LED backlights.
Both the operation of the softkeys and the LEDs can be configured using
Crimson.

TROUBLESHOOTING YOUR GRAPHITE

If for any reason you have trouble operating, connecting, or simply have
questions concerning your new Graphite, contact Red Lion’s technical support.
For contact information, refer to the back page of this bulletin for phone and
fax numbers.

EMAIL: [e-mail]
Web Site: http://www.redlion.net

BATTERY & TIME KEEPING

WARNING - EXPLOSION HAZARD - THE AREA MUST BE
KNOWN TO BE NON-HAZARDOUS BEFORE SERVICING/
REPLACING THE UNIT AND BEFORE INSTALLING OR
REMOVING I/O WIRING AND BATTERY.

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT
EQUIPMENT UNLESS POWER HAS BEEN DISCONNECTED
AND THE AREA IS KNOWN TO BE NON-HAZARDOUS.

A battery is used to keep time when the unit is without power. Typical
accuracy (at 25°C) of the Graphite time keeping is less than one minute per
month drift. The battery of a Graphite unit does not affect the unit’s memory, all
configurations and data is stored in non-volatile memory.

Changing the Battery

To change the battery of a Graphite, first remove power to the unit. Remove
the battery cover. Grasp the top edge of the battery and push to the left to remove
the battery from the holder. Lift the battery out and replace with a new battery.

Replace the battery cover, and re-apply power. Using Crimson or the unit’s
keypad, enter the correct time and date.

* Please note that the old battery must be disposed of in a manner that
complies with your local waste regulations. The battery must not be disposed of
in fire, or in a manner whereby it may be damaged and its contents could come
into contact with human skin.

The battery used by the panel is a lithium type BR2032.

10

orDering information

DESCRIPTION PART NUMBER

Graphite 7” color touch screen, indoor, 24 VDC powered G07C0000

Graphite 7” color touch screen, indoor/outdoor, 24 VDC powered G07S0000

Graphite 9” color touch screen, indoor, 24 VDC powered G09C0000

Graphite 9” color touch screen, indoor, 24 VDC powered, additional Ethernet port G09C1000

Graphite 10” color touch screen, indoor, 24 VDC powered G10C0000

Graphite 10” color touch screen, indoor, 24 VDC powered, additional Ethernet port G10C1000

Graphite 10” high resolution display, color touch screen, indoor, 24 VDC powered G10R0000

Graphite 10” high resolution display, color touch screen, indoor, 24 VDC powered, additional Ethernet port G10R1000

Graphite 10” color touch screen, indoor/outdoor, 24 VDC powered G10S0000

Graphite 10” color touch screen, indoor/outdoor, 24 VDC powered, additional Ethernet port G10S1000

Graphite 12” color touch screen, indoor, 24 VDC powered G12C0000

Graphite 12” color touch screen, indoor, 24 VDC powered, additional Ethernet and serial port G12C1100

Graphite 15” color touch screen, indoor, 24 VDC powered G15C0000

Graphite 15” color touch screen, indoor, 24 VDC powered, additional Ethernet and serial port G15C1100

Graphite Module, Single PID, Relay and Analog Outputs GMP1RA00

Graphite Module, Single PID, Relay Outputs, Heater Current Monitor GMP1RM00

Graphite Module, Single PID, SSR and Analog Outputs GMP1SA00

Graphite Module, Single PID, SSR Outputs, Heater Current Monitor GMP1SM00

Graphite Module, Dual PID, Relay Outputs GMP2R000

Graphite Module, Dual PID, Relay and Heater Current Monitor Outputs GMP2RM00

Graphite Module, Dual PID, SSR Outputs GMP2S000

Graphite Module, Dual PID, SSR and Heater Current Monitor Outputs GMP2SM00

Graphite Module, Digital I/O, 8 Inputs and 6 Relays Outputs GMDIOR00

Graphite Module, Digital I/O, 8 Inputs and 6 Solid State Outputs GMDIOS00

Graphite Module, 4 Universal Inputs GMUIN400

Graphite Module, 4 Analog Outputs GMOUT400

Graphite Module, 8 DC Current Inputs GMINI800

Graphite Module, 8 DC Voltage Inputs GMINV800

Graphite Module, 8 Thermocouple Inputs GMTC8000

Graphite Module, 6 RTD Inputs GMRTD600

11

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]

LIMITED WARRANTY

The Company warrants the products it manufactures against defects in materials and workmanship for a
period limited to two years from the date of shipment, provided the products have been stored, handled,
installed, and used under proper conditions. The Company’s liability under this limited warranty shall
extend only to the repair or replacement of a defective product, at The Company’s option. The Company

disclaims all liability for any afrmation, promise or representation with respect to the products.

The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products containing

components manufactured by RLC and based upon personal injuries, deaths, property damage, lost prots,

and other matters which Buyer, its employees, or sub-contractors are or may be to any extent liable,
including without limitation penalties imposed by the Consumer Product Safety Act (P.L. 92-573) and
liability imposed upon any person pursuant to the Magnuson-Moss Warranty Act (P.L. 93-637), as now in
effect or as amended hereafter.

No warranties expressed or implied are created with respect to The Company’s products except those
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained herein

and relies on no other warranties or afrmations.

Red Lion Controls

Europe

Softwareweg 9

NL - 3821 BN Amersfoort

Tel [phone]

Fax [phone]

Red Lion Controls

India
201-B, 2nd Floor, Park Centra
Opp 32 Mile Stone, Sector-30

Gurgaon-122002 Haryana, India

Tel [phone]

Red Lion Controls

China

Unit 302, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel [phone]

Fax [phone]