Red Goat MC-100 Installation Manual

OPERATOR'S GUIDE

FOOD CHOPPER

MODELS: SD-50, MC-50, MC-100, SD112, MC112

CONTENTS

Safety ............................................................... 2 Attachments .................................................……….. 10

General Description.......................................... 3 Troubleshooting ………............................................. 11

Unpacking and Assembly................................. 4 Lubrication and Maintenance ....................…………. 12

Cleaning ........................................................... 5 Parts Replacement and Service ...................………. 12

Electrical Requirements ................................... 8 Replacement Parts ......…............................………… 13

Operation ........……...….................................... 9

10 16.96

SAFETY

RECOGNIZE SAFETY INFORMATION. When you see this

symbol on your machine or in this manual, be alert to the
potential for personal injury,

Follow the recommended precautions and safe operating
practices.

UNDERSTAND SIGNAL WORDS. DANGER, WARNI NG
and CAUTION appear with the safety -alert symbol in this
manual and on safety labels on the machine to identify the
level of hazard seriousness.

DANGER indicates a hazard that WILL result in severe
personal injury or death.

WARNING indicates a hazard or unsafe practice which
COULD result in severe personal injury or death.

CAUTION indicates hazards or unsafe practices which
COULD result in minor personal injury or equipment
damage.

READ ALL INSTRUCTIONS
Read this operator's manual before using the m achine.
Failure to follow the instructions provided could result in
personal injury or equipment damage.

KEEP OUT OF REACH OF CHILDREN
This chopper is intended for commercial use only.

Operators must be 18 years of age or older.

DO NOT FEED FOOD BY HAND.
Always use the foodpusher.
Always place the product to be ground on the tray.
DO NOT OPERATE IF DAMAGED

Do not operate this chopper with a damaged cord or plug, or
if the chopper has been dropped or damaged in any
manner. Contact the nearest factory -authorized service
center for examination, repair or adjustment. (Refer to the
service center list included in the Owner's Information
Packet.)

Do not allow the cord to touch hot surfaces.
Do not allow the cord to hang over the edge of a table or
counter.
Do not allow the cord near cutting board.

DO NOT LEAVE CHOPPER UNATTENDED.
UNPLUG CHOPPER

Set the switch to OFF and unplug the chopper from the
outlet when not in use and before cleaning or removing
jams.

KEEP MACHINE AWAY FROM WATER
Do not let machine base stand in water.

Do not immerse the chopper in water or any other liquid.
ATTACHMENTS

Do not use attachments not recommended by the
manufacturer.
Follow the manufacturer's instructions for use of
attachments.

SAVE THESE INSTRUCTIONS.
Keep this booklet in a convenient location for future
reference.

2

01.15.96

GENERAL DESCRIPTION

THESE WARNING LABELS ARE ATTACHED TO THE CHOPPERS. DO NOT REMOVE THEM .

3

01 15.96

UNPACKING AND ASSEMBLY

the body by turning the bolt counter

-

clockwise.

UNPACKING

Inspect the shipping carton and its contents for shipping damage. If
you detect shipping damage to any of the contents of the carton,
notify your carrier.

The chopper is shipped in four parts: (1) chopper drive unit,
(2) cylinder head assembly, (3) tray, (4) tray support
bracket.

NOTE: Model SD-50 does not require a tray support bracket.

1. Open the carton and take out the tray, the tray support
bracket and the foodpusher.

2. Remove the foam insert, and take out the cylinder head and
the chopper drive unit.

If there are any parts missing notify us immediately at 1-800-251-

4232.
The chopper should be thoroughly cleaned and sanitized before
using to ensure sanitary conditions. (See Cleaning Sect ion.)

ASSEMBLY
CAUTION: The chopper should be installed

on a level counter top strong enough to safely
support its weight.

Tray Support Bracket

1. Remove the tray support bolt and lockwasher from the top of

2. Place the tray support bracket over the hole in the top of the
chopper (with the bracket top towards the back of the motor).

3. Replace the lockwasher and support bolt and tighten by turning
the bolt clockwise with an adjustable wrench.

4

01,1596

DISASSEMB

LY FOR CLEANING

Clean and sanitize the chopper before using the first time. after each
use, and before grinding different types of food products. Follow
company, local and state health/sanitation codes.

WARNING: Set the power switch to OFF, and unplug the
chopper before cleaning or handling.

Do NOT use caustic or abrasive cleaners.
Do NOT spray cleaning materials or water toward the switch case,
reset button, or motor cooling opening

Remove the tray by lifting upward.

CLEANING

Cylinder Head Assembly

1. Loosen the ring collar by turning a quarter turn counter-clockwise.

2. Loosen the thumbscrew by turning three turns counter-clockwise.

3. Remove the cylinder head by pulling it forward.

4. Loosen the ring collar by turning three turns counter-clockwise.

5. Push the feedscrew shaft forward into the cylinder head.

5