Red Goat ASM-HD Installation Manual
Operator's Manual
Use and Care
IMPORTANT: READ THIS MANUAL BEFORE USING NEW COMMERCIAL SLICER
It is of extreme importance to take a few minutes and read this booklet thoroughly before using
the new slicer. This will help you obtain the full benefits of the quality, convenience and safet y built
into this product. Used and maintained according to the following instructions, the slicer will give
you years of trouble free service. Keep this booklet in a handy location for future reference.
IMPORTANT SAFEGUARDS
When using electric appliances, basic safety precautions should always be followed including the
following:
1. READ ALL INSTRUCTIONS .
2. To protect against electrical hazards, DO NOT IMMERSE THE SLICER IN WATER OR ANY
OTHER LIQUID.
3. Unplug from outlet when not in use—also before putting on or taking off parts and before
cleaning.
4. Do not operate this slicer with a damaged cord or plug or after the slicer has been dropped or
damaged in any manner. Contact the nearest Service Agency for examination, repair or
5. Do not let the cord hang over the edge of a table or counter, or touch hot surfaces.
6. Remove all attachments from slicer before washing.
7. NEVER LEAVE SLICER UNATTENDED while unit is operating.
8. The use of attachments not recommended by the manufacturer may cause hazards.
9. Follow manufacturer's instructions for use of attachments to be used with slicer.
10. KEEP OUT OF REACH OF CHILDREN.
11. SAVE THESE INSTRUCTIONS .
ASSEMBLY
The new slicer comes to you fully assembled and ready for use; however, the machine should be
inspected for any signs of shipping damage. Even though it is anew machine, the slicer should be
thoroughly cleaned and sanitized before using to ensure sanitary conditions—follow the
cleaning instructions found in this manual.
1
2
This safety information sheet is supplied
with the slicer. Familiarize yourself with
these guidelines and post the sheet near
the slicer as a reminder.
2
INSTALLATION
The slicer is intended for placement on any rigid,
level surface capable of supporting the weight of the
machine. For normal counter top use it is not
necessary to secure the slicer unless it is to be used
on board ship or for similar applications.
NOTE: Before starting slicer the shipping gearbox oil
plug should be replaced with the vented plug
supplied with slicer. (Fig. 4) Save the shipping plug
in the accessory box for possible future use
DISASSEMBLY FOR
CLEANING
CAUTION: Unplug slicer and set regulator knob to
"0" before cleaning or handling. (Fig. 5)
FOOD PUSHER REMOVAL
1. Slide platform to extreme forward position (toward
you).
2. Unscrew and remove knob at end of food pusher
shaft. (Fig. 6)
3. Slide food pusher up and off shaft. (Fig. 6)
3
FOOD FENCE REMOVAL
1. Loosen lock knob (counter-clockwise.) (Fig. 7)
2. Slide fence off of platform. (Fig. 7)
PLATFORM REMOVAL
1. Unscrew (counter-clockwise) and remove platform knob. (Fig 81)
2. Pull platform assembly straight out and off of slicer. (Fig. 9)
KNIFEWIPER REMOVAL
NOTE: The knifewiper is located at the lower back side of knife in the
receiving area.
1. Unscrew and remove thumbscrew (counter-clockwise) (Fig. 10)
2. Remove knifewiper by pulling straight out.
4
KNIFE SHARPENER REMOVAL
CAUTION: EXTREME CARE SHOULD BE USED WHEN REMOVING THE KNIFE
SHARPENER AS THIS WILL LEAVE A PORTION OF THE KNIFE EXPOSED.
1. Loosen the sharpener lock knob (on far side of sharpener, Fig. 11)
2. Pull sharpener straight up to its st op. (Fig. 12) DO NOT Unscrew knob.
3. Turn sharpener 1/2 turn clockwise. (Fig. 13)
4. Lift up to remove from slicer (Fig. 13)
KNIFE COVER REMOVAL
CAUTION: DO NOT TOUCH KNIFE. SHARP EDGES WILL CUT.
1. Platform should be removed as described earlier.
2. Unscrew (counter-clockwise) and remove knob and rod assembly. (Fig. 14)
3. Grasp knife cover by thumbscrews shown in figure 15.
4. Holding thumbscrews (Fig. 16) remove knife cover by pulling straight out and off of slicer.
5
Loading...