Red Digital Cinema Weapon 6.1 DSMC Operation Guide
RED DSMC OPERATION GUIDE:
WEAPON
WEAPON (CArbON FibEr) | WEAPON (MAgNEsiuM)
V6.1| rED DrAgON
RED.COM
RED DSMC OPERATION GUIDE: WEAPON
TABLE OF CONTENTS
Disclaimer 3
Copyright Notice 3
Trademark Disclaimer 3
Compliance Statements 4
Safety Instructions 6
Battery Storage and Handling 7
Shipping Disclaimer 7
Chapter 1: WEAPON Introduction 8
Read Before You Shoot 8
DSMC BRAIN 9
RED Digital Sensors 9
R3D File Format and REDCODE 10
Shoot For Video and Stills 11
Post Production with REDCINE-X PRO 11
HDRx and MAGIC MOTION 12
Additional Resources 12
Chapter 2: WEAPON System Components 13
Additional Resources 13
BRAIN 14
RED MINI-MAG System 19
Expanders 20
Power Modules 23
RED Batteries and Chargers 23
Displays and Electronic Viewfinders 24
LEMO Adaptors 28
Camera Control Modules 29
Lens Mounts 31
Interchangeable OLPFs 31
Rails, Mounts, Tactical Gear, and Cables 31
Chapter 3: WEAPON Basic Operations 32
Power Operations 32
Configure Your WEAPON 34
Interchangeable OLPF System 38
Use a Tripod or Monopod 39
Video Monitor Outputs 39
Record 40
Chapter 4: Basic Menus and Controls 42
WEAPON GUI Menu Introduction 42
Upper Status Row (Basic Menu) 43
Live Action Area 47
Lower Status Row 48
Navigation Controls 53
Chapter 5: Advanced Menus 58
Advanced Menus 58
Settings Menu 59
Media Menu 110
Playback Menu 112
Power Menu 115
HDRX Menu 116
Focus Menu 117
Exposure Assist 123
Presets Menu 125
Chapter 6: Record and Monitor Audio 128
Overview 128
Set Up Audio 128
Control 128
Mix 131
Audio Output Options 131
Audio Meter (VU Meter) 131
Audio During Playback 132
Chapter 7: Timecode, Genlock, Multi-Camera Setup 133
Timecode 133
Genlock 136
Set Up Motion Control (MoCo) 138
Compatible Devices 140
Chapter 8: Upgrade DSMC Firmware 141
Verify Current Camera Firmware 141
Upgrade Camera Firmware 141
Chapter 9: DSMC Maintenance 143
BRAIN and Accessory Exterior Surfaces 143
LCD and EVF Screens 143
Water Damage 144
Adjust Back Focus 144
Chapter 10: Troubleshoot Your DSMC 145
Perform a Stress Test 145
General Troubleshooting 145
Appendix A: Technical Specifications 152
WEAPON 6K (Carbon Fiber) 152
WEAPON 6K (Magnesium) 154
WEAPON BRAIN Dimensions 156
Appendix B: Input/Output Connectors 162
DSMC2 Base Expander 163
DSMC2 REDVOLT Expander 164
DSMC2 Jetpack Expander 165
Record/Monitor Out Ports 166
Communication Ports 168
Audio Ports 172
Power Ports 173
Appendix C: Lens Mounts and Lenses 175
Lens Mounts 175
Lenses 178
Appendix D: Default Key Functions 185
Appendix E: Menu Map 186
COPYrigHT © 2015 rED.COM, iNC
955-0116_V6.1, rEV-J | 2
RED DSMC OPERATION GUIDE: WEAPON
DISCLAIMER
RED® has made every effort to provide clear and accurate information in these installation instructions, which are provided solely for
the user’s information. While thought to be accurate, the information
in this document is provided strictly “as is” and RED will not be held
responsible for issues arising from typographical errors or user’s
interpretation of the language used herein that is different from that
intended by RED. All safety and general information is subject to
change as a result of changes in local, federal or other applicable
laws.
RED reserves the right to revise this document and make changes
from time to time in the content hereof without obligation to notify
any person of such revisions or changes. In no event shall RED, its
employees or authorized agents be liable to you for any damages
or losses, direct or indirect, arising from the use of any technical or
operational information contained in this document.
For comments or questions about content in this Operation Guide,
please send a detailed email to OpsGuides@red.com.
COPYRIGHT NOTICE
COPYRIGHT© 2015 RED.COM, INC.
All trademarks, trade names, logos, icons, images, written material,
code, and product names used in association with the accompanying product are the copyrights, trademarks, or other intellectual
property owned and controlled exclusively by RED.COM, INC.
COPYrigHT © 2015 rED.COM, iNC
TRADEMARK DISCLAIMER
All other company, brand, and product names are trademarks or
registered trademarks of their respective holders. RED has no affiliation to, is not associated with or sponsored by, and has no express
rights in third-party trademarks. Adobe is a registered trademark of
Adobe Systems Incorporated. AJA is a registered trademark of AJA
Video Systems, Inc. Cooke and S4/i are registered trademarks of
Cooke Optics Limited. DaVinci is a registered trademark of Blackmagic Design in the U.S. and other countries. Distagon and Otus
are registered trademarks of Carl Zeiss AG. Fujinon is a registered
trademark of FUJIFILM CORPORATION. HDMI is a registered trademark of HDMI Licensing LLC in the United States and other countries. Leica is a registered trademark of Leica Microsystems. Loctite
is a registered trademark of Henkel AG & Company KGaA. Nikkor
and Nikon are registered trademarks of Nikon Corporation. Canon
is a registered trademark of Canon, U.S.A. Apple, Macintosh, and
QuickTime are registered trademarks of Apple Inc. in the U.S. and
other countries. Windex is a registered trademark of S. C. Johnson
& Son, Inc. Windows is a registered trademark of Microsoft Corporation. LEMO is a registered trademark of LEMO USA. Sony is
a registered trademark of Sony Corporation. TORX is a registered
trademark of Acument Intellectual Properties, LLC in the United
States or other countries.
955-0116_V6.1, rEV-J | 3
RED DSMC OPERATION GUIDE: WEAPON
COMPLIANCE STATEMENTS
INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS
This device complies with Industry Canada license-exempt RSS
standards RSS 139 and RSS 210. Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Le présent appareil est conforme aux CNR d’Industrie Canada ap-
plicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS
This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio fre-
quency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes
and modifications made to the equipment without the approval of
manufacturer could void the users authority to operate this equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operations subjected to the following two conditions (1) this device
may not cause harmful interference, and (2) this device must accept
any interference received, including that may cause undesirable interference.
CAUTION: Exposure to Radio Frequency Radiation.
CAUTION: Regulations of the FCC and FAA
prohibit airborne operation of radio-frequency
wireless devices because there signals could
interfere with critical aircraft instruments.
CAUTION: If the device is changed or modified
without permission from RED, the user may
void his or her authority to operate the equipment.
AUSTRALIA AND NEW ZEALAND STATEMENTS
RED declares that the radio equipment described in this document
comply with the following international standards.
IEC 60065 - Product Safety
ETSI EN 300 328 - Technical requirement for radio equipment
RED declares digital devices described in this document comply
with the following Australian and New Zealand standards.
AS/NZS CISPR 22 – Electromagnetic Interference
AS/NZS 61000.3.2 – Power Line Harmonics
AS/NZS 61000.3.3 – Power Line Flicker
JAPAN STATEMENTS
This is a Class B product based on the
standard of the Voluntary Control Council
for Interference (VCCI) for information technology equipment. If this equipment is used
near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment
according to the instruction manual.
EUROPEAN UNION COMPLIANCE STATEMENTS
RED declares that the radio
equipment described in this
document comply with the
R&TTE Directive (1999/5/
EC) issued by the Commission of the European Community.
Compliance with this directive implies conformity to the following
European Norms (in brackets are the equivalent international standards).
EN 60065 (IEC 60065) – Product Safety
ETSI EN 300 328 Technical requirement for radio equipment
ETSI EN 301 489 General EMC requirements for radio equip-
ment.
The device shall be used in such a manner that the potential for human contact is minimized
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 cm between
the radiator and your body.
COPYrigHT © 2015 rED.COM, iNC
955-0116_V6.1, rEV-J | 4
RED DSMC OPERATION GUIDE: WEAPON
INFORMATION
Products with the CE marking comply with the EMC Directive
(2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued
by the Commission of the European Community. Compliance with
these directives implies conformity to the following European Product Family Standards.
EN 55022 (CISPR 22) – Electromagnetic Interference
EN 55024-1 (CISPR 24) – Electromagnetic Immunity
EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics
EN 61000-3-3 (IEC610000) – Power Line Flicker
EN 60065 (IEC60065) – Product Safety
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
The Waste Electrical and Electronic Equip-
ment (WEEE) mark applies only to countries
within the European Union (EU) and Norway.
This symbol on the product and accompany-
ing documents means that used electrical
and electronic products should not be mixed
with general household waste. For proper
treatment, recovery and recycling, please
take this product to designated collection
points where it will be accepted free of
charge. Alternatively, in some countries you
may be able to return your products to your
local retailer upon purchase of an equivalent
new product.
Disposing of this product correctly will help save valuable resources
and prevent any potential negative effects on human health and the
environment, which could otherwise arise from inappropriate waste
handling. Please contact your local authority for further details of
your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with you
national legislation.
For business users in the European Union, if you wish to discard
electrical and electronic equipment, please contact your dealer or
supplier for further information.
NORWAY
This subsection does not apply for the geographical area within a
radius of 20 km from the centre of Ny-Ålesund
Dette gjelder ikke for det geografiske området innenfor en radius av
20 km fra sentrum av Ny-Ålesund
RESPONSIBLE PARTY
RED Digital Cinema
34 Parker
Irvine, CA 92618
USA
USAGE RESTRICTIONS FOR PRODUCTS THAT INCORPORATE
REDLINK
Products that fall into this category are denoted
by inclusion of the Class 2 identifier symbol (exclamation mark in a circle) accompanying the CE
Mark on the products regulatory label, example
to the left.
FRANCE
Usage Restrictions - Geographic Area Where Restriction Applies :
France
For mainland France
2.400 - 2.4835 GHz (Channels 1-16) authorized for indoor use
2.400 - 2.454 GHz (Channels 1-10) authorized for outdoor use
Restrictions d’utilisation - Zone géographique où les restrictions
s’appliquent : France
Pour la France métropolitaine
2.400 - 2.4835 GHz (Canaux 1 à 16) autorisé en usage intérieur
2.400 - 2.454 GHz (canaux 1 à 10) autorisé en usage extérieur
COPYrigHT © 2015 rED.COM, iNC
955-0116_V6.1, rEV-J | 5
RED DSMC OPERATION GUIDE: WEAPON
SAFETY INSTRUCTIONS
DO NOT use the camera or accessories near water. Avoid ex-
posing your camera to moisture. The unit is not waterproof,
so contact with water could cause permanent damage to the
unit as well as electric shock and serious injury to the user. DO
NOT use the camera in the rain or under other conditions with
high moisture without appropriate protection, and immediately
remove power source if camera or accessories are exposed to
moisture.
WARNING: To reduce the risk of fire or electric shock, do not expose the camera to
rain or moisture.
DO NOT expose the DSMC® to laser beams, as laser beams
may damage the sensor.
DO NOT expose your camera to excessive vibration or impact
(shock). Be careful not to drop your camera. Internal mechanisms may be damaged by severe shock. Mechanical alignment
of optical elements may be affected by excessive vibration.
ELECTROMAGNETIC INTERFERENCE: The use of devices us-
ing radio or other communication waves may result in the malfunction or interference with the unit and/or with audio and
video signals.
Clean only using a dry cloth. When cleaning your camera, re-
member that it is not waterproof and moisture can damage
electronic circuitry. DO NOT rinse or immerse any element
of the camera, lens or other accessory, keep them dry at all
times. DO NOT use soaps, detergents, ammonia, alkaline
cleaners, and abrasive cleaning compounds or solvents. These
substances may damage lens coatings and electronic circuitry.
Maintain sufficient ventilation—DO NOT block any ventilation
openings or obstruct cooling fan airflow.
CAUTION: Proper camera ventilation requires a minimum 0.5" (1.25 cm) clearance
between the camera ventilation openings
and external surfaces. Verify that objects
that can block the fan intake and exhaust ports do not impede airflow. Failure
to permit adequate airflow may result in
overheating of the camera, degraded operation and in extreme situations, damage
to the camera.
DO NOT operate or store near any heat sources such as radia-
tors, heat registers, stoves, or any other apparatus that produce heat. Store in a protected, level and ventilated place.
Avoid exposure to temperature extremes, damp, severe vibration, strong magnetic fields, direct sunlight or local heat sources during storage. Remove any batteries from the camera before storage. Recommended storage and usage temperatures
for your camera, lenses and other accessories are:
‒ Operating range: 0°C to 40°C (32°F to 104°F)
‒ Storage range: –20°C to 50°C (–4°F to 122°F)
If there are any performance issues with your camera or accessories when operating within this temperature range, please
file a support ticket on https://support.red.com.
The expanders, modules, and lens mounts are NOT HOT
SWAPPABLE, meaning you cannot remove or install them while
the camera is turned on. Before installing or removing any of
these accessories, you MUST turn off the camera. Failure to
do so may result in damage to the accessory and/or camera
BRAIN that will not be covered under warranty.
DO NOT bypass the third prong of the grounding-type plug on
the power cord of the DSMC AC Power Adaptor. A groundingtype plug has two blades and a third “grounding” prong. The
third prong is provided for your safety. A grounding-type plug
shall be connected to an outlet with a protective earthen connection. If the grounding-type plug does not fit into your outlet,
do not attempt to modify the plug or outlet, consult a qualified
electrician.
Protect all power cords from being pinched, walked on or
driven over by a vehicle. Replace any power cords suspected
of sustaining damage due to crushing or other forms physical
damage.
Products marked with this symbol are
class 2 devices. These devices are not
provided with a grounding type plug.
CAUTION: The power cord plug for the
DSMC AC Power Adaptor is used as the
power disconnect. To disconnect all power
from the DSMC AC Power Adaptor, unplug
the power cord plug from the wall outlet.
During use, the power cord plug should
remain easily accessible at all times.
Lithium-ion batteries may be subject to special handling re-
quirements pursuant to federal and local laws. Please refer to
specific shipping instructions included with your battery regarding proper transport of your battery. Do not handle your
battery if it is damaged or leaking. Disposal of batteries must
be in accordance with local environmental regulations. For
example, California law requires that all rechargeable batteries must be recycled by an authorized recycle center. Storing
batteries fully charged or in high temperature conditions may
permanently reduce the life of the battery. Available battery
capacity may also be temporarily lessened after storage in low
temperature conditions.
WARNING: DO NOT expose the battery to
excessive heat.
WARNING: Danger of explosion if an incorrect battery is charged with the RED Charger or is used to power the camera and
accessories. Replace only with the same
or equivalent type battery.
CAUTION: Refer all service and repair to
qualified RED service personnel. To reduce
the risk of electric shock, and damage to
the camera or accessories, DO NOT attempt to perform any servicing other than
any procedures that are recommended in
the operating instructions.
INDOOR USE ONLY: Products marked with
this symbol are designed for use indoors
only.
COPYrigHT © 2015 rED.COM, iNC
955-0116_V6.1, rEV-J | 6
RED DSMC OPERATION GUIDE: WEAPON
BATTERY STORAGE AND HANDLING
WARNING: Failure to read, understand, and fol-
low these instructions may result in overheating, chemical leakage, smoke emission, fire, or
other potentially harmful results.
Always follow proper battery handling and storage practices. Improper handling and/or failure to abide by proper storage instructions may cause permanent damage to batteries, or degrade battery
charge holding capacity. Improper handling practices or failure to
comply with instructions may also put you at risk.
Lithium-Ion batteries, like the REDVOLT
®
, self-discharge over time. When storing for long periods
BRICK
of time, store batteries separately from the camera or charger and
remember to charge batteries to a capacity level of 40% to 60%. If
batteries will be stored for long periods of time, RED recommends
that you check the charge level at least once every six (6) months,
and recharge batteries to a capacity level of 40% to 60%.
When not in use, remove the battery from the camera or charger and
store the battery in a cool, dry place. Avoid extreme hot temperatures (such as inside a hot car), corrosive gas, and direct sunlight.
The optimal storage temperature for batteries is between –20°C to
20°C (–4°F to 68°F).
WARNING: Batteries stored in a discharged state
for long periods of time may self-discharge and
lose the ability to hold a charge.
WARNING: If recharging operation fails to complete even when a specified recharging time
has elapsed, immediately stop further recharging.
DO NOT store batteries in a fully charged state for extended
DO NOT store batteries in a fully charged state for extended
periods of time.
DO NOT store batteries in a fully discharged state for extended
periods of time.
DO NOT store batteries in the camera, in a camera module, or
in a charger for extended periods of time.
DO NOT use batteries for purposes other than their intended
use.
DO NOT store batteries in extreme hot or cold temperatures.
DO NOT store batteries in direct sunlight.
DO NOT use third-party chargers with your RED batteries.
DO NOT disassemble or modify the battery.
DO NOT overcharge batteries. Overcharging may increase in-
ternal temperature beyond the recommended limits and cause
permanent damage to the battery.
DO NOT connect the positive (+) and negative (–) terminals to
a metal object such as a wire.
DO NOT transport or store the battery together with metal ob-
jects such as jewelry, hairpins, etc. as they may generate heat
if they come into contact with the battery.
DO NOT discard the battery into fire or heat.
DO NOT store, use, or recharge the battery near a heat source
such as a fire or a heater.
DO NOT allow the battery to get wet.
®
, REDVOLT XL, and RED
DO NOT pierce the battery with pointed or other sharp objects.
DO NOT step on, throw, or strike the battery with a hammer.
DO NOT use a battery that appears to be deformed or dam-
aged.
DO NOT directly solder the battery.
DO NOT put the battery into a microwave oven or a pressur-
ized container.
DO NOT use or subject the battery to intense sunlight or hot
temperatures such as in a car in hot weather.
DO NOT use it in a location where static electricity may be
present.
DO NOT exceed the recharging temperature range of 0˚C to
40˚C (32˚F to 104˚F).
RED recommends that you only use RED chargers to recharge
RED batteries.
Store the battery in a location where children cannot reach it.
If the battery leaks or gives off a bad odor, discontinue use
immediately.
If the battery gives off an odor, generates heat, becomes dis-
colored or deformed, or in any way appears abnormal dur-
ing use, recharging or storage, immediately remove it from the
equipment or battery charger and discontinue use.
If electrolyte begins leaking from the battery and comes into
contact with your skin or clothing, immediately wash it away
with running water. Failure to do this may result in skin inflam-
mation.
If the battery leaks and the electrolyte reaches the eyes, do
not rub them. Instead, rinse the eyes with clean running water
and immediately seek medical attention. Failure to do this may
result in eye injury.
If you find discoloration, a bad odor due to leakage, overheat-
ing and/or other irregularities when using the battery for the
first time, contact your Bomb Squad representative immedi-
ately.
NOTE: For more information regarding RED battery charging and instructions for care, please
refer to our Terms and Conditions.
SHIPPING DISCLAIMER
Shipment of Lithium Ion cells and batteries is subject to national
and international shipping requirements. A Class 9 Certified shipper
is required to transport these products within the United States.
REDVOLT, REDVOLT XL, and RED BRICK batteries are considered
Dangerous Goods. Other products such as REDVOLT AA and RED
Li 7.2V batteries may also be classified as Dangerous Goods when
purchased in bulk. Applicable laws prohibit the shipping of batteries
that are physically damaged. We urge you to look into the formal
rules and regulations of shipping Class 9 Dangerous Goods prior to
preparing your shipment. For more information on these regulations,
please visit www.iata.org and www.dot.gov.
For more information, see our FAQs for Regulated Items (Dangerous
Goods.
COPYrigHT © 2015 rED.COM, iNC
955-0116_V6.1, rEV-J | 7
RED DSMC OPERATION GUIDE: WEAPON
WEAPON
01
The WEAPON® cameras are part of the RED® Digital Still and Motion Camera (DSMC®) system. The DSMC
family includes WEAPON, EPIC, and SCARLET® cameras. With an ultra-high megapixel count, high frame rate,
significant processing power, high dynamic range, and the advantages of a raw file format, each DSMC offers
the ability to simultaneously capture video and stills.
This guide is for WEAPON only. This section introduces the imaging capabilities and advanced features of
the WEAPON system. For information about EPIC/SCARLET cameras, see the DSMC Operation Guide: EPIC/
SCARLET, available at www.red.com/downloads.
The WEAPON system includes the following cameras (organized by sensor type):
INTRODUCTION
WEAPON System
SENSOR TYPE CAMERA
®
RED DRAGON
RED DRAGON 8K WEAPON 8K (Carbon Fiber)
NOTE: This guide uses the term “WEAPON (Carbon Fiber)” to refer to both “WEAPON Forged CF” and
“WEAPON Woven CF”.
6K WEAPON 6K (Carbon Fiber)
WEAPON 6K (Magnesium)
READ BEFORE YOU SHOOT
Read this operation guide carefully and in its entirety before assembling or operating your DSMC or other RED
accessories. In addition to this document, RED offers the following operation guides for the DSMC system:
DSMC Power Operation Guide
DSMC Media Operation Guide
To download RED operation guides, visit the RED downloads page at www.red.com/downloads.
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 8
RED DSMC OPERATION GUIDE: WEAPON
DSMC BRAIN
WEAPON (Carbon Fiber)
At the center of the RED modular system is the DSMC BRAIN®, housing the critical image capture electronics
and digital image sensor.
The expansive RED arsenal of DSMC modules, monitors, lens mounts, controllers, power, media, and other
accessories supports WEAPON BRAINs. Modular DSMC lens mounts enable you to use your existing Canon®,
Nikon®, Leica-M®, and PL lenses to capture the perfect shot.
WEAPON (CARBON FIBER)
Manufactured with ultra-lightweight carbon fiber, the WEAPON (Carbon Fiber) delivers a new level of intuitive
control and ergonomic design. The WEAPON (Carbon Fiber) offers features such as on-board Apple® ProRes
recording and 3D LUTs.
WEAPON (MAgNESIUM)
Manufactured from lightweight and element-resistant magnesium, the WEAPON (Magnesium) delivers a new
level of intuitive control and ergonomic design. The WEAPON (Magnesium) offers features such as on-board
Apple ProRes recording and limited 3D LUT support.
RED DIgITAL SENSORS
Each WEAPON is equipped with one of the following sensors:
RED DRAGON (6K)
RED DRAGON (8K)
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 9
RED DSMC OPERATION GUIDE: WEAPON
RED DRAgON SENSOR (6K)
RED DRAGON
6K Resolution
The RED DRAGON (6K) sensor captures over nine (9) times more resolution than standard HD. The result is
unrivaled detail and impressive native exposure that exceeds 35mm film in both latitude and image density.
The RED DRAGON (6K) sensor is a model for image innovation, leading the way in the evolution of digital cinema
technology. Boasting an industry-leading 19 megapixels at 6K resolution, the RED DRAGON (6K) supports
100+ frames per second (FPS), 16.5+ stops of dynamic range, and advanced color science.
RED DRAgON SENSOR (8K)
RED DRAGON
8K Resolution
The RED DRAGON (8K) sensor delivers the Full Ultra HD (FUHD) experience for cinema. This sensor captures
8K 2.40:1 at up to 75 FPS.
NOTE: The RED DRAGON 8K sensor is only available with the WEAPON (Carbon Fiber).
R3D FILE FORMAT AND REDCODE
The R3D file format was developed by RED to provide an efficient and manageable RAW video data format that
promotes advanced post-production editing capabilities. In the R3D file format, the digital image received from
the sensor is formatted as a pixel-defect corrected (but in all other aspects unprocessed) 16-bit per pixel RAW
data frame. Each RAW frame, or sequence of RAW frames in a clip, is compressed using a proprietary wavelet
based REDCODE® RAW compression, then stored to a RED MINI-MAG®.
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 10
RED DSMC OPERATION GUIDE: WEAPON
RAW data is recorded independently of any RGB domain color processing such as ISO, White Balance, or
other RGB color space settings. Instead, color parameters are saved as reference metadata; that is, color is
not burned into the recorded RAW data. This recording technique promotes flexibility in RGB color processing,
which can be deferred to post-production or adjusted in the field, without affecting the recorded RAW data
image quality or dynamic range.
REDCODE is a visually lossless, wavelet-based compression codec that reduces R3D RAW files into a
manageable size, allowing longer recording times on media. The ability to compress RAW data is one of the
significant technologies that RED has brought to the industry.
For more information, see the DSMC Media Operation Guide, available at www.red.com/downloads.
NOTE: REDCINE-X PRO® can create and export .RMD “Look” files which may then be imported as camera
monitor path color processing presets. This information is stored as reference metadata, so that these color
processing choices can be the default values used in post-production. For more information, go to “Looks” on
page 126.
SHOOT FOR VIDEO AND STILLS
High resolution video, such as the digital footage captured by the DSMC, has surpassed the detail necessary
to produce professional full-sized prints. Because of the ability to record at high frame rates and resolution, the
DSMC is ideally suited to capture video and still images, simultaneously.
The DSMC is equipped with a Stills mode that makes it easier to capture stunning images. With presets
optimized for stills and Swipe-Up Shortcuts for the RED Touch display, switching from Motion mode to Stills
mode is seamless. Using REDCINE-X PRO, or other editing applications supporting the RED SDK, you can pull
full resolution still images from R3D files.
POST PRODUCTION WITH REDCINE-X PRO
REDCINE-X PRO
REDCINE-X PRO is a professional coloring toolset, equipped with an integrated timeline and a post effects
software collection that provides the ideal environment to edit, organize, and prepare your R3D files.
RED TETHER, included in REDCINE-X PRO, allows you to record footage from your camera directly to a
computer or an external drive. Using tethering bypasses the need to record to an SSD and offload to a
computer later, saving you time.
NOTE: RED TETHER is included in REDCINE-X PRO build 35 or later.
NOTE: RED TETHER requires a GIG-E port, which is available on the DSMC2™ REDVOLT Expander. For more
information, go to “Input/Output Connectors” on page 162.
Download the latest version of REDCINE-X PRO on the RED Downloads page at www.red.com/downloads.
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 11
RED DSMC OPERATION GUIDE: WEAPON
HDRX AND MAgIC MOTION
HDRx
HDRX
HDRx extends dynamic range up to six (6) stops by simultaneously capturing two (2) images of identical resolution
and frame rate. The first image is a normally exposed track (A-track), while the second is an underexposed
track (X-track) with an exposure value that reflects the additional stops of highlight protection. These tracks are
“motion-conjoined” during recording, leaving no time gap between the two (2) exposures. This is different from
traditional alternating exposures, which have small gaps between tracks, producing unwanted motion tracks.
MAgIC MOTION
MAGIC MOTION is a post production method that combines two (2) HDRx tracks to create an image with both
natural motion blur (from the A-track) and sharper reference (the X-track). MAGIC MOTION produces an image
with an extraordinary dynamic range that is not available with any other motion capture camera.
Shooting at 24 FPS with a 180° (1/48 sec) shutter on traditional film or digital cameras produces motion blur
throughout, which is not the way the human eye observes motion. For example, ask someone to swing their
arm. What you would observe in a traditional recording of this action is constant motion blur until the arm stops.
However, what your eye sees is both motion blur and a sharper reference of the arm throughout the motion
path. MAGIC MOTION creates an image that matches the natural motion observed by the human eye.
ADDITIONAL RESOURCES
The following resources offer additional information about RED, the DSMC system, and the RED community:
RED.com: Check the official RED website for the latest information about RED products.
RED Learn Articles: RED offers in-depth technical articles about RED cameras, post-production, and digital
cinematography.
RED.com/downloads: Go to the RED Downloads page to download the latest firmware, operation guides,
and post-production software.
DSMC Toolkit: Go to the RED Downloads page to find the DSMC Toolkit, which offers many helpful tools and
resources to customize and improve your DSMC workflow.
Support.red.com: Check the RED SUPPORT site for FAQs, or to file a support ticket.
Bomb Squad Support: For more information, contact your Bomb Squad representative.
In-Camera Help: Select the Help button on an in-camera screen to open up the help for that screen.
Reduser.net: Discuss all things RED on the REDUSER third-party forum.
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 12
RED DSMC OPERATION GUIDE: WEAPON
WEAPON SYSTEM
02
This section provides an overview of the WEAPON® system components, including:
“BRAIN” on page 14
“RED MINI-MAG System” on page 19
“Expanders” on page 20
“RED Batteries and Chargers” on page 23
“Displays and Electronic Viewfinders” on page 24
“LEMO Adaptors” on page 28
“Camera Control Modules” on page 29
“Lens Mounts” on page 31
“Interchangeable OLPFs” on page 31
“Rails, Mounts, Tactical Gear, and Cables” on page 31
WARNING: Modules, displays, and accessories are NOT HOT SWAPPABLE, meaning that you cannot remove or
install the item while the camera is turned on. Before installing or removing a module, display, or accessory,
you MUST turn off the camera. Failure to do so may result in damage to the item or DSMC® that is not covered
under warranty.
NOTE: Availability of components listed in this chapter is subject to change at any time.
COMPONENTS
WEAPON (Woven CF)
Package
ADDITIONAL RESOURCES
For more information on power and media, see the following guides, available at www.red.com/downloads:
DSMC Power Operation Guide
DSMC Media Operation Guide
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 13
RED DSMC OPERATION GUIDE: WEAPON
BRAIN
WEAPON (Carbon Fiber)
The DSMC BRAIN® is the image processing center of the DSMC system and supports power, media, and other
modules.
The only ports on the WEAPON BRAIN are the DSMC2™ Top Handle port and EVF/LCD ports. A port expander or
power module is required to power the camera. All other input/ouput (I/O) ports are available only via expanders
and other modules. This modular approach allows you to customize your camera and make use of the ports
that are most applicable to your needs.
The RED® Tactical Hand Controller (T.H.C.) cannot pair directly to the WEAPON camera. To use the T.H.C. with
the WEAPON, the T.H.C. needs to be connected to the W.M.D. (either wired or wirelessly). For more information
about WEAPON, see the RED 3-Axis System Operation Guide at www.red.com/downloads.
BRAIN CONTROL: PWR/REC BUTTON
Fully press and hold the PWR/REC button for two (2) seconds to turn on/off.
When the DSMC is on, fully press and then release the PWR/REC button to toggle record start/stop.
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 14
RED DSMC OPERATION GUIDE: WEAPON
BRAIN LEDS
This section describes the LED functions for the WEAPON BRAIN.
LED COLOR/FLASHING DESCRIPTION
Power Status LED
(PWR)
Record Status LED
(REC)
Power Status LED (PWR)
and Record Status LED (REC)
Off No power present
Green Power present; camera on
Amber flashing Power present; 5–10 min of battery time left
Amber Power present; camera booting
Red flashing Power present; < 5 min of battery time left
Red Power present; camera off
Off No media present
Green Ready to record
Amber Finalizing
Red flashing (slow) Recording; 25% media left
Red flashing (fast) Recording; 5% media left
Red Recording
Both green flashing Firmware update in progress
Both red flashing Firmware update error
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 15
RED DSMC OPERATION GUIDE: WEAPON
BRAIN CONNECTORS, FOCUS HOOK, AND BACK FOCUS
2
1
3
4
6
5
WEAPON BRAIN
Ports and Features
This section describes the ports and features on the BRAIN.
NOTE: For more information on how to install the focus hook, go to “Install the Focus Hook” on page 37.
# PORT/ITEM DESCRIPTION
1 Primary EVF/LCD Port
2 Top Handle Port
3 Secondary EVF/LCD Port
4 Focus Hook Mounting Point Mount the focus hook
5 Focus Hook Storage Location Store the focus hook
6 Back Focus Adjustment Screw Adjust back focus
1. The DSMC2 LEMO Adaptor A allows you to mount other RED® displays.
2. Shown with the DSMC
ward).
3. The secondary LCD/EVF port and an HDMI
Select” on page 66.
4. Shown with the DSMC2 LEMO Adaptor A attached.
2
Top Handle attached. This is the only mounting option for the DSMC2 Top Handle (it cannot be attached back-
1
2
1,3,4
Mount a DSMC2 RED Touch LCD
Mount the DSMC2 Top Handle
Mount a DSMC2 RED Touch LCD
®
port cannot be used at the same time. For more information, go to “LCD/EVF 2 / HDMI
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 16
RED DSMC OPERATION GUIDE: WEAPON
WEAPON MEDIA BAY CONTROLS
1
2
3
WEAPON Media Bay Controls
This section describes the control functions for the media bay.
# CONTROL DESCRIPTION
1 User Key 1 Programmable key
User Key 1 + 2 Press: Eject Media
2 REC button Programmable key
Full Press: Record Toggle
Half Press: AF Start
3 User Key 2 Programmable key
User Key 1 + 2 Press: Eject Media
For more information, see the DSMC Media Operation Guide, available at www.red.com/downloads.
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 17
RED DSMC OPERATION GUIDE: WEAPON
WEAPON MEDIA BAY LEDS
1
2
WEAPON Media Bay LEDs
This section describes the LED functions for the media bay.
# LED COLOR/FLASHING DESCRIPTION
1 Media Status LED
(Back of media bay)
2 Record Status LED
1. For more information on how to enable/disable this LED, go to “Indicator” on page 93. If media is not mounted, this LED is off.
1
Off No media mounted
Green Preview; media mounted with > 10% of
media space available
Amber Record finalizing or playback mode
Amber flashing (slow) Formatting media
Red flashing (slow) Preview/Recoding; media mounted
with <= 10% and > 5% of media space
available
Red flashing (fast) Preview/Recording; media mounted
with <= 5% of media space available
Red Recording; media mounted with > 10%
of media space available
Off Not recording, or media not mounted
Red Recording
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 18
RED DSMC OPERATION GUIDE: WEAPON
RED MINI-MAG SYSTEM
RED MINI-MAG (1TB)
RED MINI-MAG® SSDs deliver fast and reliable recording options for your camera. A RED STATION® enables
you to connect media to your computer for offloading and editing.
RED offers the following RED MINI-MAG SSDs and compatible RED STATIONs:
ITEM PART NUMBER
RED MINI-MAG (1TB)
RED MINI-MAG (512GB)
RED MINI-MAG (240GB)
RED MINI-MAG (120GB) 750-0075
RED STATION RED MINI-MAG 750-0055
1. The RED MINI-MAG 1TB can take up to 20 seconds to mount to a computer or a DSMC.
For more information, see the DSMC Media Operation Guide, available at www.red.com/downloads.
1
750-0068
750-0053
750-0072
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 19
RED DSMC OPERATION GUIDE: WEAPON
EXPANDERS
NOTE: Only one (1) expander module can be used at a time.
RED offers the following DSMC
ITEM PART NUMBER
2
DSMC
DSMC
DSMC
Base Expander 720-0033
2
REDVOLT Expander 720-0040
2
Jetpack Expander 720-0039
DSMC2 BASE EXPANDER
2
expanders:
DSMC2 Base Expander
The DSMC2 Base Expander is an ideal connector module for general input/output (I/O) needs. Manufactured
from lightweight and durable magnesium, this low-profile module mounts directly to the WEAPON BRAIN and
offers interface connections for power (DC IN), HDMI, 3G-SDI (HD-SDI), CTRL and SYNC ports (for Timecode
and Genlock), as well as a 3.5mm microphone input and a 3.5mm line-level headphone out.
The DSMC2 Base Expander also offers rear-mounting support for WEAPON-compatible battery and power
modules, such as the DSMC2 REDVOLT® XL Module. The low profile DSMC2 Base Expander offers a variety of
connectors and is ideal for run-and-gun and independent shooters.
NOTE: Only one (1) expander module can be used at a time.
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 20
RED DSMC OPERATION GUIDE: WEAPON
DSMC2 REDVOLT EXPANDER
DSMC2 REDVOLT Expander
Designed for advanced configurations, the DSMC2 REDVOLT® Expander mounts directly to the BRAIN and
offers an expansive array of I/O connectors and functionality available for the WEAPON system. The DSMC2
REDVOLT Expander features ports for power in (DC IN), Genlock (BNC), Timecode (LEMO), GIG-E, and more.
HDMI and two 3G-SDI (HD-SDI) outputs offer versatility for your video output needs, while an integrated USB
power output is available to support wireless HDMI transmitters.
The DSMC2 REDVOLT Expander offers a modular audio system that you can remove and replace with upcoming
audio modules. The default audio module offers two (2) female XLR audio connections. Each XLR input features
a 3-position selector switch to designate the incoming audio signal type: Balanced Line Level, Balanced Mic
Level, and Balanced Mic with +48V phantom power. Additionally, a 3.5mm line-level headphone jack lets you
sample audio during takes and in playback mode.
The DSMC
camera accessories and more:
A rear-facing 4-Pin 0B LEMO AUX PWR output supports Start/Stop Trigger IN, Tally OUT, and provides
power out up to 1.5 Amps.
A front-facing 2-Pin 0B LEMO AUX PWR port and front-facing 7-Pin 0B LEMO SERIAL port share a total
output of 3.0 Amps. The SERIAL port is ideal for powering motor drivers.
A rear-facing Timecode port offers 5V at 1.5 mA for powering external timecode devices.
A rear-facing USB port offers 5V at 1.5 Amps for powering HDMI transmitters or small mobile devices.
The two XLR audio ports in the default audio module each offer +48V phantom power.
For hot-swap support when it matters most, the DSMC
battery. Additional WEAPON-compatible battery and power modules can be mounted for your changing power
needs.
The DSMC
when power is provided via the DC IN connector on the expander. This feature allows you to use a connected
DC input supply to turn the BRAIN on and off when the camera is mounted in remote or difficult to maneuver
locations. This expander is the ideal solution for a variety of production environments, maximizing camera
interface and functionality for the most demanding shoots.
NOTE: Only one (1) expander module can be used at a time.
2
REDVOLT Expander also provides multiple auxiliary power outputs, enabling the use of peripheral
2
REDVOLT Expander also supports a single REDVOLT
2
REDVOLT Expander also features a selector switch that enables the BRAIN to automatically boot
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 21
RED DSMC OPERATION GUIDE: WEAPON
DSMC2 JETPACK EXPANDER
DSMC2 Jetpack Expander
The DSMC2 Jetpack Expander is specifically designed for aerial, gimbal, handheld, and other lightweight/remote
configurations. This expander features standard connectors for power (DC-IN), CTRL, and SYNC for all of your
Timecode and Genlock needs. In addition, the DSMC2 Jetpack Expander offers custom-tailored supports and
connectors for HDMI and USB power out—perfect for housings and low-profile setups.
The DSMC2 Jetpack Expander also features a selector switch that enables the WEAPON BRAIN to automatically
boot when power is provided via the DC IN connector on the expander. This feature allows you to use a
connected DC input supply to turn the BRAIN on and off when the camera is mounted in remote or difficult to
maneuver locations.
NOTE: Only one (1) expander module can be used at a time.
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 22
RED DSMC OPERATION GUIDE: WEAPON
POWER MODULES
RED offers the following WEAPON power modules:
ITEM PART NUMBER
2
DSMC
DSMC2 REDVOLT XL MODULE
REDVOLT XL Module 740-0034
DSMC2 REDVOLT XL Module
The DSMC2 REDVOLT XL Module mounts seamlessly to the back of the BRAIN—and select other I/O expanders—
to provide support for long-lasting and rechargeable REDVOLT XL batteries. The DSMC2 REDVOLT XL Module
features a smaller, more ergonomic design with one (1) dual-action release button for removing an attached
battery.
The DSMC2 REDVOLT XL Module offers a DC IN power port that can be used to power the camera system
when the module is attached to the BRAIN. An included protective baseplate enables the DSMC2 REDVOLT
XL Module to serve as a portable and stand-alone REDVOLT XL battery charger. Plug in the DSMC AC Power
Adaptor to the 6-pin 1B LEMO DC IN connector on the module and connect a REDVOLT XL battery. While the
module is mounted to the BRAIN, it will only charge an attached REDVOLT XL battery if the BRAIN is powered
off.
Two (2) rear facing auxiliary ports provide power for external camera accessories, while remaining out of the
way while shooting.
RED BATTERIES AND CHARGERS
RED offers the following batteries and chargers:
ITEM PART NUMBER
REDVOLT XL 740-0021
REDVOLT Charger (Quad) 740-0015
For more information, see the DSMC Power Operation Guide, available at www.red.com/downloads.
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 23
RED DSMC OPERATION GUIDE: WEAPON
DISPLAYS AND ELECTRONIC VIEWFINDERS
RED offers the following displays and electronic viewfinders (EVFs):
ITEM RESOLUTION PART NUMBER
2
DSMC
DSMC
RED Touch 5.0" LCD
RED Touch 7.0" LCD
RED Touch 9.0" LCD
RED PRO LCD 7"
DSMC
BOMB EVF
BOMB EVF (OLED)
1. Using this display with an EPIC or SCARLET camera requires a DSMC2 LEMO Adaptor B.
2. Using this display with a WEAPON camera requires a DSMC2 LEMO Adaptor A.
3. RED offers multiple mounting solutions for each camera type.
RED Touch 7.0" LCD
2
RED Touch 4.7" LCD
2
2
2
2
2
RED EVF (OLED)
®
(LCOS)
2
2
For a full list of LCD and EVF user keys and default actions, go to “Default Key Functions” on page 185.
1
1
1920 x 1136 730-0018
1280 x 720 730-0019
800 x 400 730-0008
1920 x 1136 730-0007
1280 x 768 730-0011
1024 x 600 730-0009
3
1920 x 1080 730-0021
1280 x 784 730-0004
1280 x 1024 730-0010
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 24
RED DSMC OPERATION GUIDE: WEAPON
RED LCDS
DSMC2 RED Touch 7.0" LCD
RED displays provide important camera parameters on the graphical user interface (GUI) and offer a variety of
monitor viewing options. RED touchscreen displays enable you to use gestures to navigate menus and adjust
camera parameters. RED displays feature 8-bit RGB, 4:4:4 progressive scan, providing up to 16.7 million colors
and up to 70% NTSC color gamut.
LCD PRECAUTIONS
WARNING: DO NOT use a RED display as a handle to lift or carry the DSMC. Damage to a RED display or other
components of the DSMC system caused by using the display as a handle are not covered under warranty.
WARNING: DO NOT use the threaded holes in the RED Touch LCD base to mount the display to the BRAIN.
Damage to a RED display or other components of the DSMC system caused by using these threaded holes is
not covered under warranty.
IMPORTANT: The RED Touch LCD swivel axis has a total adjustment range of approximately 360˚ (180˚ clockwise
or counterclockwise from the nominal “rear-facing” orientation). The tilt axis range of adjustment is approximately
180˚. Damage to a RED display or other DSMC components caused by excessive force is not covered under
warranty.
IMPORTANT: The DSMC
backward). Damage to a RED display or other DSMC components caused by excessive force is not covered
under warranty.
2
RED Touch 4.7" LCD has a tilt axis range of approximately 240˚ (90˚ forward and 150˚
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 25
RED DSMC OPERATION GUIDE: WEAPON
BOMB EVFS
The BOMB EVF (LCOS) and BOMB EVF (OLED) deliver specialized viewing solutions for the DSMC. The BOMB
EVF (LCOS) is a high-definition, lightweight, and low-profile viewfinder. The BOMB EVF (OLED) uses OLED
technology, providing deeper blacks and more color accurate images.
ITEM CONTRAST RATIO DIOPTER RANGE
BOMB EVF (LCOS)
BOMB EVF (OLED)
1. Using these displays with a WEAPON camera requires a DSMC2 LEMO Adaptor A.
WARNING: DO NOT point the BOMB EVF (OLED) eyepiece at direct sunlight. Continued exposure to direct
sunlight may damage the EVF. Point the eyepiece away from sunlight when not in use. Damage to the BOMB
EVF (OLED) caused by continued exposure to direct sunlight is not covered under warranty.
1
1
BOMB EVF FEATURES
1
1000:1 typical 2.0 to –5.0.1
>10,000:1 typical 2.0 to –5.0.1
5
2
3
# FEATURE DESCRIPTION
1 EVF connector Custom digital video and power interconnection between the BRAIN and RED
2 EVF Tally LED When enabled, the LED illuminates red when recording; For more information,
3 Key 1 Programmable key
4 Key 2 Programmable key
5 Eyepiece heater The integrated eyepiece heater automatically heats the eyepiece when the
4
EVF; Pinout not published
go to “Indicator” on page 93
Magnify: Toggle
Exposure Check: Toggle
EVF detects a low ambient temperature
BOMB EVF (OLED)
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 26
RED DSMC OPERATION GUIDE: WEAPON
DSMC2 RED EVF
The DSMC2 RED EVF (OLED) is a high definition electronic viewfinder designed as the ideal single-viewer
monitoring solution. Featuring the latest OLED technology, this EVF provides an unmatched personal viewing
experience with a 1080p OLED micro-display, and improved color accuracy with 30-bit RGB color represenation.
View and monitor your RED footage as it is intended with truer colors and deeper blacks in a larger field of view.
Engineered with OBSOLESCENCE OBSOLETE
WEAPON, EPIC, or SCARLET cameras. RED offers multiple mounting solutions for each camera type.
WARNING: DO NOT point the DSMC2 RED EVF (OLED) eyepiece at direct sunlight. Continued exposure to direct
sunlight may damage the EVF. Point the eyepiece away from sunlight when not in use. Damage to the DSMC2
RED EVF (OLED) caused by continued exposure to direct sunlight is not covered under warranty.
DSMC2 RED EVF FEATURES
®
in mind, the DSMC2 RED EVF (OLED) is perfect for use with
1
5
2
3
4
# FEATURE DESCRIPTION
2
1 DSMC
2 EVF connector
3 Key 1 Programmable key
RED EVF Mount The DSMC2 RED EVF Mount
1
Custom digital video and power interconnection between the EVF and
other RED devices; Pinout not published
Magnify: Toggle
6
DSMC2 RED EVF
4 Key 2 Programmable key
Exposure Check: Toggle
2
5 Mounting point Mounting point for the DSMC
2
6 DSMC
Modular Optical Block
1. Not visible. Shown with the DSMC2 RED EVF Mount attached.
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 27
RED EVF
Fully coated with a > 32° field of view
RED EVF Mounting Plate (Top)
RED DSMC OPERATION GUIDE: WEAPON
LEMO ADAPTORS
This section describes the DSMC2 LEMO Adaptor A and the DSMC2 LEMO Adaptor B. These adaptors enable
you to use EPIC/SCARLET displays with your WEAPON camera and use WEAPON displays with your EPIC/
SCARLET camera. For more information on available displays, go to “Displays and Electronic Viewfinders” on
page 24.
ITEM PART NUMBER
2
DSMC
DSMC
LEMO ADAPTOR A
LEMO Adaptor A 720-0037
2
LEMO Adaptor B 720-0038
DSMC2 LEMO Adaptor A
The DSMC2 LEMO Adaptor A makes your existing RED Touch and RED PRO displays, as well as RED EVFs, fully
compatible with the WEAPON camera system. The DSMC2 LEMO Adaptor A converts the pogo connection on
the WEAPON BRAIN to a legacy EVF/LCD LEMO port. The DSMC2 LEMO Adaptor A is designed to attach to
the primary (top), or the secondary (side) EVF/LCD port on the WEAPON BRAIN.
When used along with the DSMC2 LEMO Adaptor B, this adaptor enables you to mount a DSMC2 RED Touch
LCD away from the camera BRAIN—to a NOGA arm or other stable mounting point.
The DSMC2 LEMO Adaptor A is compatible with the BOMB EVF, (LCOS) and (OLED) models, or later.
LEMO ADAPTOR B
DSMC2 LEMO Adaptor B
The DSMC2 LEMO Adaptor B enables you to use a DSMC2 RED Touch LCD with your existing EPIC or SCARLET
camera BRAIN. The DSMC2 LEMO Adaptor B converts the display signal from a pogo connection to a legacy
EVF/LCD LEMO port. The DSMC2 LEMO Adaptor B is designed to mount to your EPIC or SCARLET camera
BRAIN using standard 1/4-20 mounting holes.
2
When used along with the DSMC
LCD away from the camera BRAIN—to a NOGA arm or other stable mounting point.
LEMO Adaptor A, this adaptor enables you to mount a DSMC2 RED Touch
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 28
RED DSMC OPERATION GUIDE: WEAPON
CAMERA CONTROL MODULES
This section describes the camera control modules. These devices provide a wide array of programmable
buttons, controls, and other features to interact with the camera.
RED offers the following remotes and controls:
ITEM PART NUMBER
2
DSMC
DSMC
DSMC
DSMC
1. Each DSMC2 Sidekick is compatible with both WEAPON (Carbon Fiber) and WEAPON (Magnesium).
Sidekick (Forged CF)
2
Sidekick (Woven CF)
2
Sidekick (Magnesium)
2
Top Handle 720-0035
1
1
1
720-0041
720-0036
720-0032
COPYRIGHT © 2015 RED.COM, INC 955-0116_V6.1, REV-J | 29
RED DSMC OPERATION GUIDE: WEAPON
DSMC2 SIDEKICK
DSMC2 Sidekick (Woven CF)
The DSMC2 Sidekick is a lightweight interface solution that offers intuitive integrated control over critical
camera parameters. Engineered exclusively for WEAPON, this low profile interface provides full access to basic
and advanced menus via a 1.7" OLED display. The rotary dial, D-Pad, function buttons, and configurable preset
buttons provide an improved method of controlling your camera.
The DSMC2 Sidekick provides full menu control without compromising the tactical advantages of your WEAPON’s
small form-factor and weight.
DSMC2 TOP HANDLE
DSMC2 Top Handle
Ergonomic and intuitive, the DSMC2 Top Handle was engineered entirely around the most important action
for any shooter—the record button. This intelligent top handle puts a new Record Start/Stop button at your
fingertips, using built-in integrated circuitry.
The DSMC2 Top Handle mounts directly to the 1/4-20 mounting points on the top of the WEAPON. With a
rubberized grip and new trigger design—the DSMC2 Top Handle offers the ideal handle and shooting method
for your WEAPON.
COPYRIGHT © 2015 RED.COM, INC
955-0116_V6.1, REV-J | 30
Loading...