Page 1
Executive Desk
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
A.
To p
1 pc.
F.
Front Rail
1 pc.
G.
Back Panel
1 pc.
B.
Side Frame
1 pc.
D.
Front Frame
1 pc.
Hardware List
C.
Side Frame
1 pc.
E.
Front Frame
1 pc.
L.
Keyboard
1 pc.
H.
Divider
1 pc.
K.
Keyboard
1 pc.
M.
Drawer
2 pcs.
Refer to the last page(s) of these
instructions for drawer assembly.
I.
Divider
1 pc.
J.
Stretcher
1 pc.
M3x32
Wood Screw (long)
6 pcs. (+1 extra)
M3x16
Wood Screw (short)
8 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Cam Lock Screw
8 pcs. (+1 extra)
Cam Lock
8 pcs. (+4 extra)
Tool(s) required for assembly: Phillips screwdriver, Level
M3x25
Wood Screw
16 pcs. (+1 extra)
M3x10
Wood Screw
for Hinge
6 pcs. (+1 extra)
M6x32
Head Cap Bolt
21 pcs. (+1 extra)
Flat Washer
21 pcs. (+1 extra)
Spring Washer
21 pcs. (+1 extra)
Knob
4 pcs.
M4x38
Machine Screw
4 pcs.
Page 2
Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
STEP 1
Insert Cam Lock Screws into
pre-drilled holes of Front Frames
(D), (E) and Back Panel (G).
(See Figure 1)
D
Cam Lock Screw
G
E
D
Figure 1
STEP 2
Attach Front Frames (D) and (E)
to Front Rail (F) with Wood Screws (long).
(See Figure 2)
Figure 2
Wood Screw (long)
E
F
Cam Lock
G
I
H
STEP 3
Attach Dividers (H) and (I) to unit
with Cam Locks. (See Figure 3)
Attach Back Panel (G) to
unit with Cam Locks.
Figure 3
Page 3
Assembly Instructions 3/5
Wood Screw (long)
J
C
Head Cap Bolt
Flat Washer
Spring Washer
STEP 4
Attach Side Frame (B) to unit with Flat Washers,
Spring Washers, Head Cap Bolts. (See Figure 4)
Attach Stretcher (J) to unit with Wood Screw (long). (See Figure 5)
Attach Side Frame (C) to unit with Flat Washers,
Spring Washers, Head Cap Bolts and Wood Screw (long).
B
STEP 5
Figure 4
Head Cap Bolt
Spring Washer
Flat Washer
Figure 5
A
Place Top (A) upside down on a soft cloth.
Attach unit to Top (A) with Flat Washers, Spring Washers and Head Cap Bolts.
Page 4
Assembly Instructions 4/5
STEP 6
Attach Keyboard (L) to Keyboard (K)
with Wood Screws for Hinge.
Wood Screw
for Hinge
Attach Knobs to Keyboard
with Machine Screws.
(See Figure 6)
Figure 6
K
L
MM
STEP 7
Turn unit over to its’ upright position.
Slide Keyboard and Drawers (M) into place.
M
Level unit by adjusting the adjustable levelers on the bottom of legs.
(See Figure 7)
Figure 7
Page 5
Drawer (M)
Assembly Instructions 5/5
M1
M3
M2
Roller at back
STEP 2
Slide Drawer Bottom (M5) into the grooves
of Drawer Sides (M3) and (M4) until it meets
Drawer Front (M1).
Attach Drawer Bottom (M5) to unit with
Wood Screws (short).
STEP 1
Attach Drawer Front (M1) and Drawer
Back (M2) to Drawer Side (M3) with
Wood Screws.
M4
Attach Drawer Side (M4) to unit with
Wood Screws.
M1
M3
M5
M4
Part List
M1.
Drawer Front
2 pcs.
M2.
Drawer Back
2 pcs.
M3.
Drawer Side
2 pcs.
M2
STEP 3
Attach Knob with Machine Screw.
M4.
Drawer Side
2 pcs.
M5.
Drawer Bottom
2 pcs.
Page 6
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, is under noobligation to provide replacement parts. Parts are not available forfully assembled
items nor are parts available forsale.Replacements for missing or damaged hardware or parts mayberequested
Loading...