Page 1
Assembly Instructions
COUNTER TABLE
COUNTER CHAIR (SET INCLUDES 4 CHAIRS)
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the PARTS LIST and/or HARDWARE LIST shown below.
Caution: Please read the instructions thoroughly before assembly.
1. We recommend that you assemble this product with the assistance of another person; this will make the
assembly easier, and will help eliminate damage to the product or injury to persons during assembly.
2. Please do not over tighten screws or bolts until the assembly is completed.
3. Please put all parts on a non-abrasive floor before assembly,and follow the assembly steps to assemble
your newly purchased product correctly and efficently.
PARTS LIST HARDWARE LIST
NO.ACOMPONENT
CHAIR BACK
B SEAT FRAME
C CUSHION SEAT
D
D
E
FRONT LEG
(LEFT)
FRONT LEG
(RIGHT)
SIDE
STRETCHER
(LEFT)
SKETCH QTY.
4 PCS
4 PCS
4 PCS
4 PCS
4 PCS
4 PCS
NO.1COMPONENT
FLAT WASHER
5/16” DIA.
SPRING
2
3
4
5
6
WASHER
5/16” DIA.
NUT
5/16” DIA.
ALLEN
WRENCH
5/16” DIA.
SHORT BOLT
1/4” x 1 3/4”
LONG BOLT
1/4” x 3”
SKETCH QTY.
44 PCS
44 PCS
16 PCS
1 PC
12 PCS
16 PCS
E
F
SIDE
STRETCHER
(RIGHT)
FRONT
STRETCHER
4 PCS
4 PCS
WOOD SCREW
7
5/32” x 1 1/2”
48 PCS
PAGE: 1 OF 3
Page 2
Assembly Instructions
COUNTER TABLE
COUNTER CHAIR (SET INCLUDES 4 CHAIRS)
To assemble the chairs, please follow the following steps and repeat for each chair:
STEP 1
Lay the chair back on soft clean surface and install
the seat frame.
B
4
6
2
1
A
1
2
5
4
STEP 3
Install front stretcher into the holes of the front legs
then attached to the seat frame.
STEP 2
Insert side stretchers with wood screws.
B
A
E (Left)
7
7
E (Right)
STEP 4
Place the assembled seat frame on the cushion seat
and attach with wood screws.
1
D (Right)
A
2
3
4
D (Left)
B
7
7
7
7
7
PAGE: 2 OF 3
E (Right)
F
7
7
7
7
E (Left)
7
Page 3
Assembly Instructions
COUNTER TABLE
COUNTER CHAIR (SET INCLUDES 4 CHAIRS)
PARTS LIST HARDWARE LIST
NO.
A
B
C
COMPONENT
TABLE TOP
TABLE LEG
TABLE SHELF
SKETCH QTY.
1 PC
4 PCS
2 PCS
To assemble the table, please follow the following
steps but do not tighten all bolts:
STEP 1
Attached the table shelves to two of the table legs.
C
1
2
4
3
B
NO.
1
2
3
4
COMPONENT
BOLT
5/16” x 2 1/2”
SPRING WASHER
5/16” DIA.
FLAT WASHER
5/16” DIA.
ALLEN KEY
1/4” DIA.
STEP 2
Attached the two other legs.
C
B
SKETCH QTY.
12 PCS
12 PCS
12 PCS
1 PC
B
2
1
4
3
C
B
STEP 3
Turn the assembly upright and place the table top on
the assembled unit.
A
B
C
STEP 4
Secure the table top with bolts. Make sure the table is
level, then tighten all bolts.
A
3
B
2
1
4
PAGE: 3 OF 3
Loading...